Study on the quality and tooth root load carrying capacity of the high contact ratio asymmetrical gear tooth machined using WCEDM process
Source abstract
Abstract
This work aims to report the quality of the high contact ratio asymmetrical gear tooth manufactured through wire cut electrical discharge machining(WCEDM) process and static load capacity of the gear tooth. The effect of various process parameters such as peak current (IP), pulse on time (Ton), pulse off time (Toff) and servo voltage (SV) on the performance parameters such as Surface roughness (Ra) and Kerf width (Kf) has been examined on the regular shaped specimen. Taguchi method was used with process parameters at three levels and the significance of WCEDM process parameters was studied through analysis of variance (ANOVA). Based on the significant process parameter values, the gears were manufactured and gear tooth errors such as profile, lead and pitch errors were estimated based on DIN3962 Standard using the Gleason inspection system and found that the range of quality of the gear obtained through this process was from Q8-Q11. The experimental test results conducted to explore the tooth root load carrying capacity of the gear tooth revealed that the gear with lower pressure angle at the non-drive side (17º-20º) has a maximum load carrying capacity and maximum yielding when compared to symmetric (20º-20º) and asymmetric gears with higher pressure angle at the non-drive side (22º-20º).
Source: openalex_inverted_index · Quality: baseline
Research context
OpenAlex topics: Advanced Machining and Optimization Techniques · Advanced machining processes and optimization · Gear and Bearing Dynamics Analysis
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
Affiliations
Department of Mechanical Engineering, Dr. Mahalingam College of Engineering and Technology, Coimbatore, Tamilnadu, India
Department of Mechanical EngineeringTamilnadu, Dr. Mahalingam College of Engineering and Technology, Coimbatore, Tamilnadu, India
References (23)
Show source-provided references
1. 10.1016/S0094-114X(99)00002-610.1016/S0094-114X(99)00002-6 ↗
2. 10.1016/j.mechmachtheory.2007.06.00610.1016/j.mechmachtheory.2007.06.006 ↗
3. 10.1016/j.proeng.2014.11.08910.1016/j.proeng.2014.11.089 ↗
4. 10.1016/j.mechmachtheory.2014.04.02110.1016/j.mechmachtheory.2014.04.021 ↗
5. 10.1080/15397734.2011.54048810.1080/15397734.2011.540488 ↗
6. 10.1504/IJCAT.2013.05429810.1504/IJCAT.2013.054298 ↗
7. 10.1016/j.apsusc.2016.09.00910.1016/j.apsusc.2016.09.009 ↗
8. 10.1186/s40759-017-0017-110.1186/s40759-017-0017-1 ↗
9. 10.1007/s00170-016-9881-910.1007/s00170-016-9881-9 ↗
10. 10.1080/10426914.2018.153209210.1080/10426914.2018.1532092 ↗
11. 10.1080/10910344.2011.55796610.1080/10910344.2011.557966 ↗
12. 10.1177/095440541246277810.1177/0954405412462778 ↗
13. 10.1016/j.jmatprotec.2005.04.10510.1016/j.jmatprotec.2005.04.105 ↗
14. 10.1016/j.eswa.2010.04.02010.1016/j.eswa.2010.04.020 ↗
15. 10.1007/s00170-014-6712-810.1007/s00170-014-6712-8 ↗
16. 10.1504/IJISE.2012.04941310.1504/IJISE.2012.049413 ↗
17. 10.1080/10426914.2018.145315610.1080/10426914.2018.1453156 ↗
18. 10.1080/10426914.2014.94186510.1080/10426914.2014.941865 ↗
19. 10.1080/10426914.2013.79242210.1080/10426914.2013.792422 ↗
20. 10.1007/s12541-010-0092-210.1007/s12541-010-0092-2 ↗
21. 10.1016/j.jmatprotec.2005.06.01310.1016/j.jmatprotec.2005.06.013 ↗
22. 10.1016/j.measurement.2019.10704310.1016/j.measurement.2019.107043 ↗
23. 10.1016/j.engfailanal.2020.10438310.1016/j.engfailanal.2020.104383 ↗