journal article·2021-09-10

Investigations on milling SKT4 steel by using cryogenic carbon-dioxide

M. Jebaraj, M. Pradeep Kumar, R. Anburaj

Publisher page

Abstract

Machinability of cryogenic carbon-dioxide (CO2) coolant was compared with conventional wet coolant during end milling SKT4 die steel with TiAlN-coated cutting tools in this study. The cutting temperature values were reduced by about 3% to 51% by using CO2 compared to wet cooling. During end milling, CO2 cooling decreased by around 54% feed, 45% normal, and 32% thrust forces compared to wet condition. The die steel surface had a better surface morphology with cryogenic CO2 cooling compared to wet cooling. In particular, chips with smooth surfaces were obtained under cryogenic cooling conditions. The absence of tool edge chipping and minimum cutting tool wear were observed with cryogenic coolant.
Source: openalex_inverted_index · Quality: baseline

Research context

OpenAlex topics: Metal Alloys Wear and Properties · Advanced materials and composites · Microstructure and Mechanical Properties of Steels

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

Department of Sales and Application, Tesla Tools, Chennai, India

Department of Mechanical Engineering, CEG, Anna University, Chennai, India

Department of Mechanical Engineering, Indian Institute of Technology Madras, Chennai, India

References (18)

Show source-provided references
1. 10.1016/0141-6359(85)90098-410.1016/0141-6359(85)90098-4 ↗
2. 10.1016/j.ijmachtools.2009.02.01010.1016/j.ijmachtools.2009.02.010 ↗
3. 10.1016/S0924-0136(02)00134-610.1016/S0924-0136(02)00134-6 ↗
4. 10.1080/10426914.2019.159427110.1080/10426914.2019.1594271 ↗
5. 10.1080/10426914.2011.65415310.1080/10426914.2011.654153 ↗
6. 10.1080/10426914.2018.145315110.1080/10426914.2018.1453151 ↗
7. 10.1016/j.cirp.2007.05.02610.1016/j.cirp.2007.05.026 ↗
8. 10.1016/j.ijmachtools.2006.04.00810.1016/j.ijmachtools.2006.04.008 ↗
9. 10.1016/j.jmatprotec.2004.04.19010.1016/j.jmatprotec.2004.04.190 ↗
10. 10.1016/j.procir.2014.03.09710.1016/j.procir.2014.03.097 ↗
11. 10.4028/.scientific.net/KEM.554-557.206210.4028/.scientific.net/KEM.554-557.2062 ↗
12. 10.1080/10910344.2019.169861210.1080/10910344.2019.1698612 ↗
13. 10.1016/j.triboint.2020.10619610.1016/j.triboint.2020.106196 ↗
14. 10.1016/j.procir.2017.03.35110.1016/j.procir.2017.03.351 ↗
15. 10.1016/j.jmatprotec.2006.03.12310.1016/j.jmatprotec.2006.03.123 ↗
16. 10.1080/10426914.2018.142490810.1080/10426914.2018.1424908 ↗
17. 10.1080/10426914.2018.153259110.1080/10426914.2018.1532591 ↗
18. 10.1016/j.cirp.2016.06.00710.1016/j.cirp.2016.06.007 ↗