journal article·2022-07Open access

Effect of temperature variations on the bond behavior of FRCM applied to masonry

Francesca Ferretti, Matteo Canestri, Claudio Mazzotti

Materials and Structures· Volume 55· Issue 6

Abstract

Abstract In the last decades, Fiber Reinforced Cementitious Matrix (FRCM) composites were successfully introduced to repair and strengthen existing masonry structures. The good mechanical performances of these materials determined their efficiency as a strengthening technique; however, their durability is still an open issue. As a matter of fact, FRCM composites may be exposed to a combination of different environmental conditions and, additionally, to temperature variations due to solar radiation. The objective of this research was to study the effects of temperature variations on the bond behavior of a FRCM composite, constituted by a basalt grid and a lime-based mortar matrix, applied to masonry. For this purpose, an experimental investigation on thermally conditioned FRCM-strengthened masonry wallets is presented, in which 14 single-lap shear tests were performed. Before testing, samples were exposed to different target temperatures inside a climatic chamber: 32, 40, 50, 60 and 80 °C. Thermocouples were embedded within the FRCM reinforcing layers at two different depths to detect the inner temperature profiles and to control the conditioning process. The single-lap shear tests were then carried out inside the same climatic chamber, while maintaining the target temperature constant. A decrease in terms of peak-axial stress was observed by increasing temperature, along with a progressive change in the failure mode, from fiber rupture outside the bonded area to fiber slippage within the mortar matrix layers.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Masonry and Concrete Structural Analysis · Building materials and conservation · Hygrothermal properties of building materials

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (56)

Show source-provided references
1. Ceci AM, Contento A, Fanale L, Galeota D, Gattulli V, Lepidi M, Potenza P (2010) Structural performance of the historic and modern buildings of the University of L’Aquila during the seismic events of April 2009). Eng Struct 32:1899–1924. https://doi.org/10.1016/j.engstruct.2009.12.02310.1016/j.engstruct.2009.12.023 ↗
2. D’Ayala DF, Paganoni S (2011) Assessment and analysis of damage in L’Aquila historic city centre after 6th April 2009. Bull Earthq Eng 9:81–104. https://doi.org/10.1007/s10518-010-9224-410.1007/s10518-010-9224-4 ↗
3. Penna A, Morandi P, Rota M, Manzini CF, da Porto F, Magenes G (2014) Performance of masonry buildings during the Emilia 2012 earthquake. Bull Earthq Eng 12:2255–2273. https://doi.org/10.1007/s10518-013-9496-610.1007/s10518-013-9496-6 ↗
4. Ferretti, F, Mazzotti C, Esposito R, Rots JG (2018) Shear-sliding behavior of masonry: numerical micro-modeling of triplet tests. In: Comput. Model. Concr. Struct. CRC Press, Boca Raton, pp. 941–951. https://doi.org/10.1201/9781315182964-109.10.1201/9781315182964-109 ↗
5. Ferretti F, Ferracuti B, Mazzotti C, Savoia M (2019) Destructive and minor destructive tests on masonry buildings: experimental results and comparison between shear failure criteria. Constr Build Mater 199:12–29. https://doi.org/10.1016/j.conbuildmat.2018.11.24610.1016/j.conbuildmat.2018.11.246 ↗
6. Sorrentino L, Cattari S, da Porto F, Magenes G, Penna A, Seismic behaviour of ordinary masonry buildings during the 2016 central Italy earthquakes. Bull Earthq Eng 17:5583–5607. https://doi.org/10.1007/s10518-018-0370-410.1007/s10518-018-0370-4 ↗
7. C. Del Gaudio, S.A. Scala, P. Ricci, G.M. Verderame, Evolution of the seismic vulnerability of masonry buildings based on the damage data from L’Aquila 2009 event. Bull Earthq Eng 19:4435–4470. https://doi.org/10.1007/s10518-021-01132-x10.1007/s10518-021-01132-x ↗
8. Faella C, Martinelli E, Nigro E, Paciello S (2010) Shear capacity of masonry walls externally strengthened by a cement-based composite material: An experimental campaign. Constr Build Mater 24:84–93. https://doi.org/10.1016/j.conbuildmat.2009.08.01910.1016/j.conbuildmat.2009.08.019 ↗
9. Parisi F, Iovinella I, Balsamo A, Augenti N, Prota A (2013) In-plane behaviour of tuff masonry strengthened with inorganic matrix–grid composites. Compos Part B Eng 45:1657–1666. https://doi.org/10.1016/j.compositesb.2012.09.06810.1016/j.compositesb.2012.09.068 ↗
10. Babaeidarabad S, De Caso F, Nanni A (2014) URM walls strengthened with fabric-reinforced cementitious matrix composite subjected to diagonal compression. J Compos Constr 18:04013045. https://doi.org/10.1061/(ASCE)CC.1943-5614.000044110.1061/(ASCE)CC.1943-5614.0000441 ↗
11. Mininno G, Ghiassi B, Oliveira DV (2017) Modelling of the in-plane and out-of-plane performance of TRM-strengthened Masonry walls. Key Eng Mater 747:60–68. https://doi.org/10.4028/www.scientific.net/KEM.747.6010.4028/www.scientific.net/KEM.747.60 ↗
12. Bellini A, Incerti A, Bovo M, Mazzotti C (2018) Effectiveness of FRCM reinforcement applied to masonry walls subject to axial force and out-of-plane loads evaluated by experimental and numerical studies. Int J Archit Herit 12:376–394. https://doi.org/10.1080/15583058.2017.132324610.1080/15583058.2017.1323246 ↗
13. D’Ambra C, Lignola GP, Prota A, Fabbrocino F, Sacco E (2019) FRCM strengthening of clay brick walls for out of plane loads. Compos Part B Eng 174:107050. https://doi.org/10.1016/j.compositesb.2019.10705010.1016/j.compositesb.2019.107050 ↗
14. Castori G, Corradi M, Sperazini E (2021) Full size testing and detailed micro-modeling of the in-plane behavior of FRCM–reinforced masonry. Constr Build Mater 299:124276. https://doi.org/10.1016/j.conbuildmat.2021.12427610.1016/j.conbuildmat.2021.124276 ↗
15. Donnini J, Maracchini G, Lenci S, Corinaldesi V, Quagliarini E (2021) TRM reinforced tuff and fired clay brick masonry: Experimental and analytical investigation on their in-plane and out-of-plane behavior. Constr Build Mater 272:121643. https://doi.org/10.1016/j.conbuildmat.2020.12164310.1016/j.conbuildmat.2020.121643 ↗
16. Garcia-Ramonda L, Pelà L, Roca P, Camata G (2022) Cyclic shear-compression testing of brick masonry walls repaired and retrofitted with basalt textile reinforced mortar. Compos Struct 283:115068. https://doi.org/10.1016/j.compstruct.2021.11506810.1016/j.compstruct.2021.115068 ↗
17. Incerti A, Ferretti F, Mazzotti C (2019) FRCM strengthening systems efficiency on the shear behavior of pre-damaged masonry panels: an experimental study. J Build Pathol Rehabil 4:14. https://doi.org/10.1007/s41024-019-0053-910.1007/s41024-019-0053-9 ↗
18. Ferretti F, Incerti A, Tilocca AR, Mazzotti C (2021) In-plane shear behavior of stone masonry panels strengthened through grout injection and fiber reinforced cementitious matrices. Int J Archit Herit 15:1375–1394. https://doi.org/10.1080/15583058.2019.167580310.1080/15583058.2019.1675803 ↗
19. Ferretti F, Mazzotti C (2021) FRCM/SRG strengthened masonry in diagonal compression: experimental results and analytical approach proposal. Constr Build Mater 283:122766. https://doi.org/10.1016/j.conbuildmat.2021.12276610.1016/j.conbuildmat.2021.122766 ↗
20. Del Zoppo M, Di Ludovico M, Prota A (2019) Analysis of FRCM and CRM parameters for the in-plane shear strengthening of different URM types. Compos Part B Eng 171:20–33. https://doi.org/10.1016/j.compositesb.2019.04.02010.1016/j.compositesb.2019.04.020 ↗
21. Olivito RS, Cevallos OA, Carrozzini A (2014) Development of durable cementitious composites using sisal and flax fabrics for reinforcement of masonry structures. Mater Des 57:258–268. https://doi.org/10.1016/j.matdes.2013.11.02310.1016/j.matdes.2013.11.023 ↗
22. de Carvalho Bello CB, Boem I, Cecchi A, Gattesco N, Oliveira (2019) Experimental tests for the characterization of sisal fiber reinforced cementitious matrix for strengthening masonry structures. Constr Build Mater 219:44–55. https://doi.org/10.1016/j.conbuildmat.2019.05.168.10.1016/j.conbuildmat.2019.05.168 ↗
23. Cassese P, Balestrieri C, Fenu L, Asprone D, Parisi F (2021) In-plane shear behaviour of adobe masonry wallets strengthened with textile reinforced mortar. Constr Build Mater 306:124832. https://doi.org/10.1016/j.conbuildmat.2021.12483210.1016/j.conbuildmat.2021.124832 ↗
24. Del Zoppo M, Di Ludovico M, Balsamo A, Prota A (2019) Experimental in-plane shear capacity of clay brick masonry panels strengthened with FRCM and FRM composites. J Compos Constr 23:04019038. https://doi.org/10.1061/(ASCE)CC.1943-5614.000096510.1061/(ASCE)CC.1943-5614.0000965 ↗
25. Murgo FS, Ferretti F, Mazzotti C (2021) A discrete-cracking numerical model for the in-plane behavior of FRCM strengthened masonry panels. Bull Earthq Eng 19:4471–4502. https://doi.org/10.1007/s10518-021-01129-610.1007/s10518-021-01129-6 ↗
26. Dalalbashi A, Ghiassi B, Oliveira DV (2021) A multi-level investigation on the mechanical response of TRM-strengthened masonry. Mater Struct 54:224. https://doi.org/10.1617/s11527-021-01817-410.1617/s11527-021-01817-4 ↗
27. Nobili A, Signorini C (2017) On the effect of curing time and environmental exposure on impregnated Carbon Fabric Reinforced Cementitious Matrix (CFRCM) composite with design considerations. Compos Part B Eng 112:300–313. https://doi.org/10.1016/j.compositesb.2016.12.02210.1016/j.compositesb.2016.12.022 ↗
28. Donnini J (2019) Durability of glass FRCM systems: effects of different environments on mechanical properties. Compos Part B Eng 174:107047. https://doi.org/10.1016/j.compositesb.2019.10704710.1016/j.compositesb.2019.107047 ↗
29. Micelli F, Aiello MA (2019) Residual tensile strength of dry and impregnated reinforcement fibres after exposure to alkaline environments. Compos Part B Eng 159:490–501. https://doi.org/10.1016/j.compositesb.2017.03.00510.1016/j.compositesb.2017.03.005 ↗
30. Dalalbashi A, Ghiassi B, Oliveira DV (2021) Aging of lime-based TRM composites under natural environmental conditions. Constr Build Mater 270:121853. https://doi.org/10.1016/j.conbuildmat.2020.12185310.1016/j.conbuildmat.2020.121853 ↗
31. Bellini A, Tilocca AR, Frana I, Savoia M, Mazzotti C (2020) Environmental durability of FRCM strengthening systems and comparison with dry fabrics. In: Proceedings of 17th international brick and block masonry conference, Krakow, Poland.10.1201/9781003098508-50 ↗
32. Dalalbashi A, Ghiassi B, Oliveira DV (2021) Influence of freeze–thaw cycles on the pull-out response of lime-based TRM composites. Constr Build Mater 313:125473. https://doi.org/10.1016/j.conbuildmat.2021.12547310.1016/j.conbuildmat.2021.125473 ↗
33. Consiglio Superiore Lavori Pubblici, Linea Guida per la identificazione, la qualificazione ed il controllo di accettazione di compositi fibrorinforzati a matrice inorganica (FRCM) da utilizzarsi per il consolidamento strutturale di costruzioni esistenti (in Italian), CSLP (Consiglio Superiore dei Lavori Pubblici), Rome, Italy, 2018.
34. Ombres L (2015) Analysis of the bond between Fabric Reinforced Cementitious Mortar (FRCM) strengthening systems and concrete. Compos Part B Eng 69:418–426. https://doi.org/10.1016/j.compositesb.2014.10.02710.1016/j.compositesb.2014.10.027 ↗
35. Donnini J, De Caso y Basalo F, Corinaldesi V, Lancioni G, Nanni A (2017) Fabric-reinforced cementitious matrix behavior at high-temperature: experimental and numerical results. Compos Part B Eng 108:108–121. https://doi.org/10.1016/j.compositesb.2016.10.004.10.1016/j.compositesb.2016.10.004 ↗
36. Maroudas SR, Papanicolaou CCG (2017) Effect of high temperatures on the TRM-to-Masonry bond. Key Eng Mater 747:533–541. https://doi.org/10.4028/www.scientific.net/KEM.747.53310.4028/www.scientific.net/KEM.747.533 ↗
37. Ombres L, Iorfida A, Mazzuca S, Verre S (2018) Bond analysis of thermally conditioned FRCM-masonry joints. Measurement 125:509–515. https://doi.org/10.1016/j.measurement.2018.05.02110.1016/j.measurement.2018.05.021 ↗
38. Iorfida A, Candamano S, Crea F, Ombres L, Verre S, de Fazio P (2019) Bond behaviour of FRCM composites: effects of high temperature. Key Eng Mater 817:161–166. https://doi.org/10.4028/www.scientific.net/KEM.817.16110.4028/www.scientific.net/KEM.817.161 ↗
39. Askouni PD, Corina C, Papanicolaou G, Kaffetzakis MI (2019) The effect of elevated temperatures on the TRM-to-masonry bond: comparison of normal weight and lightweight matrices. Appl Sci 9:2156. https://doi.org/10.3390/app9102156.10.3390/app9102156 ↗
40. Estevan L, Varona FB, Baeza FJ, Torres B, Bru D (2022) Textile Reinforced Mortars (TRM) tensile behavior after high temperature exposure. Constr Build Mater 328:127116. https://doi.org/10.1016/j.conbuildmat.2022.12711610.1016/j.conbuildmat.2022.127116 ↗
41. Ferretti F, Tilocca AR, Incerti A, Mazzotti C, Savoia M (2022) Tensile behavior of FRCM coupons under thermal stresses. Key Eng Mater 916:50–57. https://doi.org/10.4028/p-rki9n610.4028/p-rki9n6 ↗
42. Ferretti F, Tilocca AR, Incerti A, Mazzotti C, Savoia M (2022) (Forthcoming) Effects of thermal variations on the tensile behavior of FRCM strengthening systems. J Compos Constr. https://doi.org/10.1061/(ASCE)CC.1943-5614.0001241 (forthcoming)10.1061/(ASCE)CC.1943-5614.0001241 ↗
43. EN 772-1, Methods of test for masonry units - Part 1: Determination of compressive strength, (2011).
44. EN 12390-6:2009, Testing hardened concrete - Part 6: Tensile splitting strength of test specimen, (2010).
45. EN 12390-13, Testing hardened concrete - Determination of secant modulus of elasticity in compression, (2013).
46. EN 1015-11, Methods of test for mortar for masonry—Part 11: Determination of flexural and compressive strength of hardened mortar, European Committee for Standardization, 2019.
47. ACI 549.6R-20, Design and construction of externally bonded Fabric-Reinforced Cementitious Matrix (FRCM) systems for repair and strengthening concrete and masonry Structures, American Concrete Instutute (ACI), 2020.
48. Leone M, Aiello MA, Balsamo A, Carozzi FG, Ceroni F, Corradi M, Gams M, Garbin E, Gattesco N, Krajewski P, Mazzotti C, Oliveira D, Papanicolaou C, Ranocchiai G, Roscini F, Saenger D (2017) Glass fabric reinforced cementitious matrix: tensile properties and bond performance on masonry substrate. Compos Part B Eng 127:196–214. https://doi.org/10.1016/j.compositesb.2017.06.02810.1016/j.compositesb.2017.06.028 ↗
49. Carozzi FG, Bellini A, D’Antino T, de Felice G, Focacci F, Hojdys Ł, Laghi L, Lanoye E, Micelli F, Panizza M, Poggi C (2017) Experimental investigation of tensile and bond properties of Carbon-FRCM composites for strengthening masonry elements. Compos Part B Eng 128:100–119. https://doi.org/10.1016/j.compositesb.2017.06.01810.1016/j.compositesb.2017.06.018 ↗
50. Lignola GP, Caggegi C, Ceroni F, De Santis S, Krajewski P, Lourenço PB, Morganti M, (Corina) Papanicolaou C, Pellegrino C, Prota A, Zuccarino L (2017) Performance assessment of basalt FRCM for retrofit applications on masonry. Compos Part B Eng 128:1–18. https://doi.org/10.1016/j.compositesb.2017.05.003.10.1016/j.compositesb.2017.05.003 ↗
51. de Felice G, Aiello MA, Caggegi C, Ceroni F, De Santis S, Garbin E, Gattesco N, Hojdys Ł, Krajewski P, Kwiecień A, Leone M, Lignola GP, Mazzotti C, Oliveira D, Papanicolaou C, Poggi C, Triantafillou T, Valluzzi MR, Viskovic A (2018) Recommendation of RILEM Technical Committee 250-CSM: Test method for Textile Reinforced Mortar to substrate bond characterization. Mater Struct 51:95. https://doi.org/10.1617/s11527-018-1216-x10.1617/s11527-018-1216-x ↗
52. D’Antino T, Carloni C, Sneed LH, Pellegrino C (2014) Matrix–fiber bond behavior in PBO FRCM composites: a fracture mechanics approach. Eng Fract Mech 117:94–111. https://doi.org/10.1016/j.engfracmech.2014.01.01110.1016/j.engfracmech.2014.01.011 ↗
53. Bilotta A, Ceroni F, Nigro E, Pecce M (2017) Experimental tests on FRCM strengthening systems for tuff masonry elements. Constr Build Mater 138:114–133. https://doi.org/10.1016/j.conbuildmat.2017.01.12410.1016/j.conbuildmat.2017.01.124 ↗
54. Bellini A, Aiello MA, Bencardino F, de Carvalho Bello CB, Castori G, Cecchi A, Ceroni F, Corradi M, D’Antino T, De Santis S, Fagone M, de Felice G, Leone M, Lignola GP, Napoli A, Nisticò M, Poggi C, Prota A, Ranocchiai G, Realfonzo R, Sacco E, Mazzotti C (2021) Influence of different set-up parameters on the bond behavior of FRCM composites. Constr Build Mater 308:124964. https://doi.org/10.1016/j.conbuildmat.2021.124964.10.1016/j.conbuildmat.2021.124964 ↗
55. Ascione L, de Felice G, De Santis S (2015) A qualification method for externally bonded Fibre Reinforced Cementitious Matrix (FRCM) strengthening systems. Compos Part B Eng 78:497–506. https://doi.org/10.1016/j.compositesb.2015.03.07910.1016/j.compositesb.2015.03.079 ↗
56. Valluzzi MR, Oliveira DV, Caratelli A, Castori G, Corradi M, de Felice G, Garbin E, Garcia D, Garmendia L, Grande E, Ianniruberto U, Kwiecień A, Leone M, Lignola GP, Lourenço PB, Malena M, Micelli F, Panizza M, Papanicolaou CG, Prota A, Sacco E, Triantafillou TC, Viskovic A, Zając B, Zuccarino G (2012) Round Robin Test for composite-to-brick shear bond characterization. Mater Struct 45:1761–1791. https://doi.org/10.1617/s11527-012-9883-510.1617/s11527-012-9883-5 ↗