Analyzing the early structural build-up of accelerated cement pastes
Source abstract
Abstract
Abstract Extrusion-based additive manufacturing imposes high requirements on the material stability right after the extrusion. Therefore, a thorough understanding of the chemical reactions that determine the early reduction in processability is necessary. Accelerators are especially considered here, which have a major influence on the early reaction. This study contributes to these issues by analyzing the influence of 0.1 wt% TEA (triethanolamine) and 2.0 wt% Ca(NO3)2 on the hydration of two CEM I 52.5 R. The hydration was analyzed by isothermal heat flow calorimetry and in-situ X-ray diffraction. Vicat needle penetration, a penetrometer of own design, and ultrasonic P-wave velocity development were used to monitor the early change in workability. The obtained results indicate that ettringite formation is the main factor influencing workability during the first 60 min of hydration. Afterwards, the influence of ettringite is exceeded by the formation of C–S–H. Ca(NO3)2 was shown to enhance C–S–H formation and had no significant effect on the workability during the first 60 min of hydration while rapidly decreasing workability during the induction period. TEA was shown to increase brownmillerite dissolution and ettringite formation and, consequently, promote the workability loss during the initial hydration period. The time of initial and final setting determined by the Vicat needle test depended mainly on the formation of C–S–H phases.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: Innovations in Concrete and Construction Materials · Concrete and Cement Materials Research · Additive Manufacturing and 3D Printing Technologies
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (51)
Show source-provided references
1. Labonnote N, Rønnquist A, Manum B et al (2016) Additive construction. State-of-the-art, challenges and opportunities. Autom Constr 72:347–366. https://doi.org/10.1016/j.autcon.2016.08.02610.1016/j.autcon.2016.08.026 ↗
2. Pfeiffer S, Stephan D, Dorn T et al. State of the art and perspectives of 3D printing in construction. In: Leopolder F (ed) Dry mix mortar yearbook—3D special, München, pp 22–32
3. Marchon D, Kawashima S, Bessaies-Bey H et al (2018) Hydration and rheology control of concrete for digital fabrication. Potential admixtures and cement chemistry. Cem Concr Res 112:96–110. https://doi.org/10.1016/j.cemconres.2018.05.01410.1016/j.cemconres.2018.05.014 ↗
4. Le TT, Austin SA, Lim S et al (2012) Mix design and fresh properties for high-performance printing concrete. Mater Struct 45(8):1221–1232. https://doi.org/10.1617/s11527-012-9828-z10.1617/s11527-012-9828-z ↗
5. Lim S, Buswell RA, Le TT et al (2012) Developments in construction-scale additive manufacturing processes. Autom Constr 21:262–268. https://doi.org/10.1016/j.autcon.2011.06.01010.1016/j.autcon.2011.06.010 ↗
6. Perrot A, Rangeard D, Pierre A (2016) Structural built-up of cement-based materials used for 3D-printing extrusion techniques. Mater Struct 49(4):1213–1220. https://doi.org/10.1617/s11527-015-0571-010.1617/s11527-015-0571-0 ↗
7. EN 196-3:2016 (2017) Methods of testing cement. Part 3: determination of setting times and soundness
8. Bullard JW, Jennings HM, Livingston RA et al (2011) Mechanisms of cement hydration. Cem Concr Res 41(12):1208–1223. https://doi.org/10.1016/j.cemconres.2010.09.01110.1016/j.cemconres.2010.09.011 ↗
9. Scrivener KL, Nonat A (2011) Hydration of cementitious materials, present and future. Cem Concr Res 41(7):651–665. https://doi.org/10.1016/j.cemconres.2011.03.02610.1016/j.cemconres.2011.03.026 ↗
10. Jansen D, Goetz-Neunhoeffer F, Lothenbach B et al (2012) The early hydration of ordinary portland cement (OPC): an approach comparing measured heat flow with calculated heat flow from QXRD. Cem Concr Res 42(1):134–138. https://doi.org/10.1016/j.cemconres.2011.09.00110.1016/j.cemconres.2011.09.001 ↗
11. Hesse C, Goetz-Neunhoeffer F, Neubauer J (2011) A new approach in quantitative in-situ XRD of cement pastes: correlation of heat flow curves with early hydration reactions. Cem Concr Res 41(1):123–128. https://doi.org/10.1016/j.cemconres.2010.09.01410.1016/j.cemconres.2010.09.014 ↗
12. Jansen D, Goetz-Neunhoeffer F, Stabler C et al (2011) A remastered external standard method applied to the quantification of early OPC hydration. Cem Concr Res 41(6):602–608. https://doi.org/10.1016/j.cemconres.2011.03.00410.1016/j.cemconres.2011.03.004 ↗
13. Pott U, Ehm C, Jakob C et al. Investigation of the early cement hydration with a new penetration test, rheometry and in-situ XRD. In: 2nd International RILEM conference, rheology and processing of construction materials (RheoCon2), Dresden, Germany, 8th–11th September 2019, pp 246–25510.1007/978-3-030-22566-7_29 ↗
14. Jakob C, Jansen D, Pott U et al (2019) Comparing phase development and rheological properties of OPC paste within the first hour of hydration. In: 2nd International RILEM conference, rheology and processing of construction materials (RheoCon2), Dresden, Germany, 8th–11th September 2019, pp 219–227
15. Jakob C, Jansen D, Ukrainczyk N et al (2019) Relating ettringite formation and rheological changes during the initial cement hydration: a comparative study applying XRD analysis, rheological measurements and modeling. Materials 12(18):5–6. https://doi.org/10.3390/ma1218295710.3390/ma12182957 ↗
16. Damidot D, Nonat A, Barret P (1990) Kinetics of tricalcium silicate hydration in diluted suspensions by microcalorimetric measurements. J Am Ceram Soc 73(11):3319–3322. https://doi.org/10.1111/j.1151-2916.1990.tb06455.x10.1111/j.1151-2916.1990.tb06455.x ↗
17. Juilland P, Gallucci E, Flatt R et al (2010) Dissolution theory applied to the induction period in alite hydration. Cem Concr Res 40(6):831–844. https://doi.org/10.1016/j.cemconres.2010.01.01210.1016/j.cemconres.2010.01.012 ↗
18. Bazzoni A (2014) Study of early hydration mechanisms of cement by means of electron microscopy, Thèse EPFL n°6296. Dissertation, École Polytechnique Fédérale de Lausanne
19. Gallucci E, Mathur P, Scrivener KL (2010) Microstructural development of early age hydration shells around cement grains. Cem Concr Res 40(1):4–13. https://doi.org/10.1016/j.cemconres.2009.09.01510.1016/j.cemconres.2009.09.015 ↗
20. Bergold ST, Goetz-Neunhoeffer F, Neubauer J (2017) Interaction of silicate and aluminate reaction in a synthetic cement system: implications for the process of alite hydration. Cem Concr Res 93:32–44. https://doi.org/10.1016/j.cemconres.2016.12.00610.1016/j.cemconres.2016.12.006 ↗
21. Powers TC (1958) Structure and physical properties of hardened portland cement paste. J Am Ceram Soc 41(1):1–6. https://doi.org/10.1111/j.1151-2916.1958.tb13494.x10.1111/j.1151-2916.1958.tb13494.x ↗
22. Ylmén R, Jäglid U, Steenari B-M et al (2009) Early hydration and setting of Portland cement monitored by IR, SEM and Vicat techniques. Cem Concr Res 39(5):433–439. https://doi.org/10.1016/j.cemconres.2009.01.01710.1016/j.cemconres.2009.01.017 ↗
23. Roussel N, Ovarlez G, Garrault S et al (2012) The origins of thixotropy of fresh cement pastes. Cem Concr Res 42(1):148–157. https://doi.org/10.1016/j.cemconres.2011.09.00410.1016/j.cemconres.2011.09.004 ↗
24. Justnes H, Nygaard EC (1995) Technical calcium nitrate as set accelerator for cement at low temperatures. Cem Concr Res 25(8):1766–1774. https://doi.org/10.1016/0008-8846(95)00172-710.1016/0008-8846(95)00172-7 ↗
25. Myrdal R, Sintef (2007) Accelerating admixtures for concrete. State of the art (978-82-536-0989-8): 1–35. Accessed 13 Jun 2018
26. Chikh N, Cheikh-Zouaoui M, Aggoun S et al (2007) Effects of calcium nitrate and triisopropanolamine on the setting and strength evolution of Portland cement pastes. Mater Struct 41(1):31–36. https://doi.org/10.1617/s11527-006-9215-810.1617/s11527-006-9215-8 ↗
27. Dorn T, Hirsch T, Stephan D (2019) Study on the influence of accelerators on the hydration of Portland cement and their applicability in 3D printing. In: Mechtcherine, Viktor, Khayat, Kamal, Secrieru, Egor (eds) Rheology and processing of construction materials. RheoCon2 & SCC9. Springer, Basingstoke10.1007/978-3-030-22566-7_44 ↗
28. Ramachandran VS (1972) Influence of triethanolamine on the hydration characteristics of tricalcium silicate. J Appl Chem Biotechnol 22(11):1125–1138. https://doi.org/10.1002/jctb.502022110210.1002/jctb.5020221102 ↗
29. Jachiet M, Azéma N, Le Saoût G et al (2018) Influence of triethanolamine on cement pastes at early age of hydration. Adv Cem Res 30(4):159–171. https://doi.org/10.1680/jadcr.17.0004110.1680/jadcr.17.00041 ↗
30. Kong X-M (2012) Effect of organic grinding aids on cement properties and the analysis via organic cement chemistry. J Chin Ceram Soc 40(1):50–55
31. Yan-Rong Z, Xiang-Ming K, Zi-Chen L et al (2016) Influence of triethanolamine on the hydration product of portlandite in cement paste and the mechanism. Cem Concr Res 87:64–76. https://doi.org/10.1016/j.cemconres.2016.05.00910.1016/j.cemconres.2016.05.009 ↗
32. Ramachandran V (1976) Hydration of cement—role of triethanolamine. Cem Concr Res 6(5):623–631. https://doi.org/10.1016/0008-8846(76)90026-010.1016/0008-8846(76)90026-0 ↗
33. Yaphary YL, Yu Z, Lam RH et al (2017) Effect of triethanolamine on cement hydration toward initial setting time. Constr Build Mater 141:94–103. https://doi.org/10.1016/j.conbuildmat.2017.02.07210.1016/j.conbuildmat.2017.02.072 ↗
34. Ramachandran VS (1973) Action of triethanolamine on the hydration of tricalciumaluminate. Cem Concr Res 3:41–5410.1016/0008-8846(73)90060-4 ↗
35. EN 197-1:2011 Cement. Part 1: Composition, specifications and conformity criteria for common cements, 2011
36. von Daake H, Stephan D (2016) Setting of cement with controlled superplasticizer addition monitored by ultrasonic measurements and calorimetry. Cem Concr Compos 66:24–37. https://doi.org/10.1016/j.cemconcomp.2015.11.00410.1016/j.cemconcomp.2015.11.004 ↗
37. Le Saoût G, Kocaba V, Scrivener K (2011) Application of the Rietveld method to the analysis of anhydrous cement. Cem Concr Res 41(2):133–148. https://doi.org/10.1016/j.cemconres.2010.10.00310.1016/j.cemconres.2010.10.003 ↗
38. Gartner E, Myers D (1993) Influence of tertiary alkanolamines on Portland cement hydration. J Am Ceram Soc 76(6):1521–1530. https://doi.org/10.1111/j.1151-2916.1993.tb03934.x10.1111/j.1151-2916.1993.tb03934.x ↗
39. Nicoleau L, Schreiner E, Nonat A (2014) Ion-specific effects influencing the dissolution of tricalcium silicate. Cem Concr Res 59:118–138. https://doi.org/10.1016/j.cemconres.2014.02.00610.1016/j.cemconres.2014.02.006 ↗
40. Quennoz A, Scrivener KL (2013) Interactions between alite and C3A-gypsum hydrations in model cements. Cem Concr Res 44:46–54. https://doi.org/10.1016/j.cemconres.2012.10.01810.1016/j.cemconres.2012.10.018 ↗
41. Suraneni P, Flatt RJ (2015) Use of micro-reactors to obtain new insights into the factors influencing tricalcium silicate dissolution. Cem Concr Res 78:208–215. https://doi.org/10.1016/j.cemconres.2015.07.01110.1016/j.cemconres.2015.07.011 ↗
42. Odler I, Schüppstuhl J (1981) Early hydration of tricalcium silicate III. Control of the induction period. Cem Concr Res 11(5–6):765–774. https://doi.org/10.1016/0008-8846(81)90035-110.1016/0008-8846(81)90035-1 ↗
43. Mota B, Matschei T, Scrivener K (2015) The influence of sodium salts and gypsum on alite hydration. Cem Concr Res 75:53–65. https://doi.org/10.1016/j.cemconres.2015.04.01510.1016/j.cemconres.2015.04.015 ↗
44. Begarin F, Garrault S, Nonat A et al (2011) Hydration of alite containing aluminium. Adv Appl Ceram 110(3):127–130. https://doi.org/10.1179/1743676110Y.000000000710.1179/1743676110Y.0000000007 ↗
45. Aggoun S, Cheikh-Zouaoui M, Chikh N et al (2008) Effect of some admixtures on the setting time and strength evolution of cement pastes at early ages. Constr Build Mater 22(2):106–110. https://doi.org/10.1016/j.conbuildmat.2006.05.04310.1016/j.conbuildmat.2006.05.043 ↗
46. Sayers CM, Dahlin A (1993) Propagation of ultrasound through hydrating cement pastes at early times. Adv Cem Based Mater 1(1):12–21. https://doi.org/10.1016/1065-7355(93)90004-810.1016/1065-7355(93)90004-8 ↗
47. Sayers CM, Grenfell RL (1993) Ultrasonic propagation through hydrating cements. Ultrasonics 31(3):147–153. https://doi.org/10.1016/0041-624X(93)90001-G10.1016/0041-624X(93)90001-G ↗
48. Voigt T, Grosse CU, Sun Z et al (2005) Comparison of ultrasonic wave transmission and reflection measurements with P- and S-waves on early age mortar and concrete. Matériaux et Construction 38(8):729–738. https://doi.org/10.1007/BF0247928510.1007/BF02479285 ↗
49. Kong X-M, Lu Z-B, Liu H et al (2013) Influence of triethanolamine on the hydration and the strength development of cementitious systems. Mag Concr Res 65(18):1101–1109. https://doi.org/10.1680/macr.13.0001510.1680/macr.13.00015 ↗
50. Xu Z, Li W, Sun J et al (2017) Research on cement hydration and hardening with different alkanolamines. Constr Build Mater 141:296–306. https://doi.org/10.1016/j.conbuildmat.2017.03.01010.1016/j.conbuildmat.2017.03.010 ↗
51. Thomas JJ, Jennings HM, Chen JJ (2009) Influence of nucleation seeding on the hydration mechanisms of tricalcium silicate and cement. J Phys Chem C 113(11):4327–4334. https://doi.org/10.1021/jp809811w10.1021/jp809811w ↗