journal article·2021-12

Effect of shot peening on microstructure and contact fatigue crack growth mechanism of shaft steel

Shengguan Qu, Chenfeng Duan, Xiongfeng Hu, Siyu Jia, Xiaoqiang Li

Publisher page

Abstract

Abstract In this study, C53 steel was shot peened with different process parameters. The effects of shot peening pressure, coverage and shot diameter on surface hardness, roughness and residual stress of C53 steel were discussed. The effect of different shot peening parameters on the rolling contact fatigue property of C53 steel was analyzed. The results show that the coarse grains are refined into nanocrystals by shot peening, and a large number of dislocation tangles are formed. With the increase of shot peening strength, the surface hardness of C53 steel increases to 712.8 HV0.2, with an average increase of 18.3%. The maximum residual compressive stress is −677 MPa, which is 5.7 times of the original sample. And the surface roughness increases obviously. Due to dislocation tangles and nanocrystalline strengthening, the rolling contact fatigue life of C53 steel increases obviously after shot peening, but the fatigue life decreases with the increase of shot peening strength. It is found that there are two modes of rolling contact fatigue crack propagation: intergranular growth and lamellar.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Surface Treatment and Residual Stress · Metal and Thin Film Mechanics · Metal Alloys Wear and Properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (42)

Show source-provided references
1. Shot peening of austempered ductile iron gears10.1080/02670844.2016.1266118 ↗
2. Influence of laser dispersed treatment on rolling contact wear and fatigue behavior of railway, wheel steel10.1016/j.matdes.2013.08.041 ↗
3. Numerical and experimental analysis of surface roughness generated by shot peening10.1016/j.apsusc.2012.03.111 ↗
4. A micro-pitting model for spur gear contacts10.1016/j.ijfatigue.2013.08.015 ↗
5. Modelling of surface initiated rolling contact fatigue damage10.1016/j.proeng.2013.12.130 ↗
6. Effect of hardened depth on the fatigue strength of nitrided gears10.1299/kikaic.53.164 ↗
7. A tribo-dynamic contact fatigue model for spur gear pairs10.1016/j.ijfatigue.2017.01.020 ↗
8. The effects of laser peening and shot peening on high cycle fatigue in 7050–T7451 aluminum alloy10.1016/j.msea.2009.08.045 ↗
9. Numerical modeling of laser shock peening with femtosecond laser pulses and comparisons to experiments10.1016/j.apsusc.2010.02.034 ↗
10. Fatigue-crack initiation and propagation on shot-peened surfaces in A316 stainless-steel10.1016/0142-1123(95)00044-T ↗
11. Compressive residual stress introduced by shot peening10.1016/S0924-0136(97)00213-6 ↗
12. An evaluation of shot peening, residual stress and stress relaxation on the fatigue life of AISI 4340 steel10.1016/S0142-1123(01)00205-5 ↗
13. Comparative study of the effects of surface mechanical attrition treatment and conventional shot peening on low cycle fatigue of a 316L stainless steel10.1016/j.surfcoat.2018.06.041 ↗
14. Effects of shot-peening intensity on fretting fatigue crack-initiation behaviour of Ti–6Al–4V10.1111/j.1460-2695.2005.00871.x ↗
15. Improvement of fatigue property in 7050–T7451 aluminum alloy by laser peening and shot peening10.1016/j.msea.2011.01.077 ↗
16. Experimental study of shot peening and stress peen forming10.1016/j.jmatprotec.2010.07.016 ↗
17. Evaluating surface deformation and near surface strain hardening resulting from shot peening a tempered martensitic steel and application to low cycle fatigue10.1016/j.ijfatigue.2013.03.019 ↗
18. Low cycle fatigue life prediction in shot-peened components of different geometries-Part I: residual stress relaxation10.1111/ffe.12543 ↗
19. Shot peening of austempered ductile iron gears10.1080/02670844.2016.1266118 ↗
20. Role of ultrasonic shot peening on low cycle fatigue behavior of 7075 aluminium alloy10.1016/j.ijfatigue.2017.06.033 ↗
21. The effects of deep rolling and shot peening on fretting fatigue resistance of aluminum-7075-T610.1016/j.msea.2009.03.020 ↗
22. Hybrid organic/inorganic films of conducting polymers modified with phthalocyanines. I-Film preparation and voltammetric studies10.1007/s10008-006-0189-9 ↗
23. Hybrid organic/inorganic films of conducting polymers modified with phthalocyanines. II-EIS studies and film characterization10.1007/s10008-006-0190-3 ↗
24. Effect of severe shot-peening on microstructure and fatigue strength of cast iron10.1016/j.ijfatigue.2013.08.022 ↗
25. The influence of surface enhancement by low plasticity burnishing on the corrosion fatigue performance of AA7075-T610.1016/j.ijfatigue.2004.01.010 ↗
26. Residual stresses in meta/ceramic bonded strips10.1111/j.1151-2916.1985.tb15316.x ↗
27. Effects of different shot peening parameters on residual stress, surface roughness and cell size10.1016/j.surfcoat.2020.126054 ↗
28. Comparison between cavitation peening and shot peening for extending the fatigue life of a duralumin plate with a hole10.1016/j.jmatprotec.2015.08.012 ↗
29. Effects of lubrication on gear performance: a review10.1016/j.mechmachtheory.2019.103701 ↗
30. Ratchetting–multiaxial fatigue damage analysis in gear rolling contact considering tooth surface roughness
31. Effects of conventional, severe, over, and re-shot peening processes on the fatigue behavior of mild carbon steel10.1016/j.surfcoat.2018.02.081 ↗
32. Diffusion behavior of aluminum in the surface layer of iron processed by shot peening10.1016/j.matlet.2010.03.046 ↗
33. A comparative study on the corrosion performance of Ni47Ti49Co4 and Ni51Ti49 shape memory alloys in simulated saliva solution for dental applications
34. Enhanced fatigue behavior of powder metallurgy Ti-6Al-4V alloy by applying ultrasonic impact treatment10.1016/j.msea.2015.06.072 ↗
35. XRD and EBSD studies of severe shot peening induced martensite transformation and grain refinements in austenitic stainless steel10.1016/j.matchar.2020.110574 ↗
36. The effect of nitriding, severe shot peening and their combination on the fatigue behavior and micro-structure of a low-alloy steel10.1016/j.ijfatigue.2013.04.017 ↗
37. Effect of shot peening on fretting fatigue of Ti811 alloy at elevated temperature10.1016/j.ijfatigue.2008.10.004 ↗
38. Confirming subsurface initiation at non-metallic inclusions as one mechanism for white etching crack (WEC) formation10.1016/j.triboint.2014.03.012 ↗
39. Moving cracks form white etching areas during rolling contact fatigue in bearings10.1016/j.msea.2019.138659 ↗
40. Novel ultra-high straining process for bulk materials - development of the accumulative roll-bonding (ARB) process10.1016/S1359-6454(98)00365-6 ↗
41. Recent developments in explosive welding10.1016/j.matdes.2010.10.017 ↗
42. Numerical stress analysis and rolling contact fatigue of white etching layer on rail steel10.1016/j.ijfatigue.2010.08.007 ↗