Statistical and artificial neural network technique for prediction of performance in AlSi10Mg-MWCNT based composite materials
Source abstract
Abstract
Abstract The present research paper deals with AlSi10Mg alloy/MWCNT metal matrix composite brake pads with varying weight percentages. The Development of new brake pad materials has been done at compacting load (10 Tons) and sintering temperature (450 °C) using the powder metallurgy process. The input parameters of 40 N normal load, 500 rpm, 150 °C pin temperature as the near-optimal combination of parameters for minimum wear and maximum coefficient of friction compared to other test conditions have been observed by the design of experiment (DOE). The overall average percentage error in the output against experiment output is less than 1%. Analysis of variance (ANOVA) indicates that load is a most significant factor than speed and temperature for wear and CoF. Artificial Neural Network (ANN) is used to develop a prediction model to calculate wear and coefficient of friction for different loads, pin heating temperature and speed. The model developed shows a strong correlation with experimental output. The experimental and predictive model developed from artificial neural network are strongly correlated with a correlation factor of 0.99447 for the training algorithm of Levenberg-Marquardt technique. ANN prediction model and Taguchi L16 array reveal that the experimental and predicted data for mass loss and CoF have less than 3% and 4% error, respectively. The closeness between the artificial neural network and experiment results enhances the scope of ANN for predicting the wear of materials. The model will help engineers to predict the failure of components with reference to running time and can be applied in automobile or manufacturing sectors to study wear, thus saving their time and cost in carrying out experiments.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Brake Systems and Friction Analysis · Aluminum Alloys Composites Properties · Surface Treatment and Coatings
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (83)
Show source-provided references
1. Effects of aramid fiber concentration on the friction and wear characteristics of non-asbestos organic friction composites using standardized braking tests10.1016/j.wear.2016.03.002 ↗
2. Particle emission of organic brake pad material: a review
3. Morphological analysis of pad-disc system during braking operations10.1016/j.wear.2016.02.005 ↗
4. A review paper: development of novel friction material for vehicle brake pad application to minimize environmental and health issues10.1016/j.matpr.2019.06.703 ↗
5. Progress in research on hybrid metal matrix composites10.1016/j.jallcom.2020.155274 ↗
6. Towards a better understanding of the structures existing on the surface of brake pads10.1016/j.triboint.2016.09.033 ↗
7. Optimization of tribo-performance of brake friction materials
8. Results in Physics Effect of hydroxylated carbon nanotubes on the thermal and electrical properties of derived epoxy composite materials10.1016/j.rinp.2020.103246 ↗
9. Dispersion state of multi-walled carbon nanotubes in the UHMWPE matrix : E ff ects on the tribological and mechanical response10.1016/j.polymertesting.2018.08.023 ↗
10. Effect of A-MWCNTs and ETBN toughener on impact, compression and damping properties of carbon fiber reinforced epoxy composites10.1016/j.jmrt.2018.07.003 ↗
11. Assessment of wear resistance of aluminium alloy in manufacturing industry-a review10.1016/j.promfg.2019.09.007 ↗
12. Development of aluminum based AA 2014 and AA 7075 dissimilar metals for aerospace applications
13. Recent developments in powder metallurgy based aluminium alloy composite for aerospace applications10.1016/j.matpr.2019.07.568 ↗
14. Dry sliding wear and friction studies on AlSi10Mg-fly ash-graphite hybrid metal matrix composites using Taguchi method10.1179/1751584X11Y.0000000009 ↗
15. Casting of aluminium alloy with rice husk ash for
16. Kumar Moulleswaran · 2017
17. Microstructure and mechanical properties of TiC/AlSi10Mg alloy fabricated by laser additive manufacturing under high-frequency10.1016/j.jallcom.2019.04.287 ↗
18. Fousová
19. Comparative study of performance comparison of AlSi10Mg alloy prepared by selective laser melting and casting10.1016/j.jmst.2019.08.049 ↗
20. Dynamic loading of direct metal laser sintered AlSi10Mg alloy : strengthening behavior in different building directions10.1016/j.matdes.2018.08.045 ↗
21. Optik Mechanical properties of AlSi10Mg alloy fabricated by laser melting deposition and improvements via heat treatment10.1016/j.ijleo.2018.10.112 ↗
22. Very high-cycle fatigue properties and microstructural damage mechanisms of selective laser melted AlSi10Mg alloy10.1016/j.ijfatigue.2019.02.040 ↗
23. Selective laser melting of AlSi10Mg alloy : process optimisation and mechanical properties development10.1016/j.matdes.2014.09.044 ↗
24. Artificial neural network technique to predict the properties of multiwall carbon nanotube-fly ash reinforced aluminium composite10.1016/j.jmrt.2019.07.005 ↗
25. Prediction of specific wear rate for LM25/ZrO2 composites using Levenberg-Marquardt backpropagation algorithm10.1016/j.jmrt.2019.10.082 ↗
26. Parametric optimization of dry sliding wear loss of copper − MWCNT composites10.1016/S1003-6326(17)60070-0 ↗
27. Artificial neural network and regression modelling to study the effect of reinforcement and deformation on volumetric wear of red mud nano particle reinforced aluminium matrix composites synthesized by stir casting10.1016/j.bsecv.2017.09.006 ↗
28. Artificial neural network based prediction on tribological properties of polycarbonate composites reinforced with graphene and boron carbide particle10.1016/j.matpr.2019.11.276 ↗
29. Artificial neural network prediction of aging effects on the wear behavior of IN706 superalloy10.1016/j.matdes.2015.05.055 ↗
30. Experimental investigation and prediction of wear properties of Al/SiC metal matrix composites produced by thixomoulding method using Artificial Neural Networks10.1016/j.matdes.2014.06.005 ↗
31. Artificial neural network predictions on erosive wear of polymers10.1016/S0043-1648(03)00149-2 ↗
32. Artificial neural network-based prediction technique for wear loss quantities in Mo coatings10.1016/j.wear.2006.01.040 ↗
33. Comparing statistical models and artificial neural networks on predicting the tool wear in hard machining D2 AISI steel10.1007/s00170-007-0999-7 ↗
34. Predicting drill wear using an artificial neural network10.1007/s00170-004-2376-0 ↗
35. An artificial neural network approach to investigate surface roughness and vibration of workpiece in boring of AISI1040 steels10.1007/s00170-015-7621-1 ↗
36. Experimental investigation on thermally enhanced machining of high-chrome white cast iron and to study its machinability characteristics using Taguchi method and artificial neural network10.1007/s00170-014-5752-4 ↗
37. A comparison of performance of artificial intelligence methods in prediction of dry sliding wear behavior10.1007/s00170-015-7812-9 ↗
38. Wear behaviour analysis on aluminium alloy 7050 with reinforced SiC through taguchi approach10.1016/j.jmrt.2020.01.085 ↗
39. Prediction of fretting wear behavior of surface mechanical attrition treated Ti-6Al-4V using artificial neural network10.1016/j.matdes.2013.02.076 ↗
40. ANN modeling for justification of thermodynamic analysis of experimental applications on combustion parameters of a diesel engine using diesel and safflower biodiesel fuels10.1016/j.fuel.2020.118391 ↗
41. Analysis of rheological properties of MWCNT/SiO2 hydraulic oil nanolubricants using regression and artificial neural network10.1016/j.icheatmasstransfer.2020.104723 ↗
42. An artificial neural network modeling approach for short and long fatigue crack propagation10.1016/j.commatsci.2020.109962 ↗
43. Application of artificial neural networks for rigid lattice kinetic Monte Carlo studies of Cu surface diffusion10.1016/j.commatsci.2020.109789 ↗
44. Finite element simulation-based predictive regression modeling and optimum solution for grain size in machining of Ti6Al4V alloy: influence of tool geometry and cutting conditions10.1016/j.simpat.2020.102141 ↗
45. Degradation of 4-nitrophenol (4-NP) using ZnO nanoparticles supported on zeolites and modeling of experimental results by artificial neural networks10.1016/j.matchemphys.2012.01.091 ↗
46. Statistical optimization of melt-quenching process parameters for multiple properties of ternary barium phosphate glasses10.1016/j.matchemphys.2014.12.024 ↗
47. An empirical study to develop temperature-dependent models for thermal conductivity and viscosity of water-Fe3O4 magnetic nanofluid10.1016/j.matchemphys.2016.06.067 ↗
48. Friction and wear performance evaluation of UHMWPE using Taguchi based grey approach: a study on the influence of load and bio-serum lubrication10.1016/j.matchemphys.2019.121918 ↗
49. S co–doped biocarbon for supercapacitor application: effect of electrolytes concentration and modelling with artificial neural network10.1016/j.matchemphys.2020.124129 ↗
50. Three-dimensional convolutional neural network (3D-CNN) for heterogeneous material homogenization10.1016/j.commatsci.2020.109850 ↗
51. Crystallization of amorphous GeTe simulated by neural network potential addressing medium-range order10.1016/j.commatsci.2020.109725 ↗
52. Theory-training deep neural networks for an alloy solidification benchmark problem10.1016/j.commatsci.2020.109687 ↗
53. Modeling high-temperature mechanical properties of austenitic stainless steels by neural networks10.1016/j.commatsci.2020.109617 ↗
54. Simulation and sensitivity analysis of wear on the automotive brake pad10.1016/j.simpat.2018.01.009 ↗
55. A simulation approach for estimating flank wear and material removal rate in turning of Inconel 71810.1016/j.simpat.2014.12.004 ↗
56. Multi-objective optimization of the fiber-reinforced composite injection molding process using Taguchi method, RSM, and NSGA-II10.1016/j.simpat.2018.09.003 ↗
57. Neural network model as Internet of Things congestion control using PID controller and immune-hill-climbing algorithm10.1016/j.simpat.2019.102022 ↗
58. Porosity and tribological performance analysis on new developed metal matrix composite for brake pad materials10.1016/j.jmapro.2020.09.053 ↗
59. Statistical and computational analysis of an environment-friendly MWCNT/NiSO4 composite materials10.1016/j.jmapro.2021.04.001 ↗
60. Effect of weight fraction and particle size of CRT glass on the tribological behaviour of Mg-CRT-BN hybrid composites10.1016/j.triboint.2017.07.025 ↗
61. Optimization of manufacturing parameters for a brake lining using Taguchi method10.1016/S0924-0136(03)00159-6 ↗
62. Optimization of tribological properties of cement kiln dust- fi lled brake pad using grey relation analysis
63. Dry sliding wear behavior of epoxy fly ash composite with Taguchi optimization10.1016/j.jestch.2015.11.010 ↗
64. Optimization of surface roughness and flank wear using the Taguchi method in milling of Hadfield steel with PVD and CVD coated inserts10.1016/j.measurement.2013.12.017 ↗
65. Soft computing approaches for comparative prediction of the mechanical properties of jute fiber reinforced concrete10.1016/j.advengsoft.2020.102887 ↗
66. Monitoring of tool wear using measured machining forces and neuro-fuzzy modelling approaches during machining of GFRP composites10.1016/j.advengsoft.2014.12.010 ↗
67. Grzesik · 2003 · vol. 134
68. Prediction of flat-plate collector performance parameters using artificial neural networks10.1016/j.solener.2005.03.003 ↗
69. Expert Systems with Applications Taguchi Method – GONNS integration : complete procedure covering from experimental design to complex optimization10.1016/j.eswa.2010.09.170 ↗
70. Neurocomputing Taguchi method – ANN integration for predictive model of intrinsic stress in hydrogenated amorphous silicon film deposited by plasma enhanced chemical vapour deposition10.1016/j.neucom.2012.10.019 ↗
71. Friction and wear studies between cylinder liner and piston ring pair using Taguchi design method10.1016/j.advengsoft.2011.04.008 ↗
72. Force-torque based on-line tool wear estimation system for CNC milling of Inconel 718 using neural networks10.1016/j.advengsoft.2010.12.002 ↗
73. Stepwise approach for the evolution of generalized genetic programming model in prediction of surface finish of the turning process10.1016/j.advengsoft.2014.08.005 ↗
74. Static load estimation using artificial neural network: application on a wing rib10.1016/j.advengsoft.2018.01.007 ↗
75. Using of artificial neural networks (ANNs) to predict the thermal conductivity of zinc oxide–silver (50%–50%)/water hybrid Newtonian nanofluid10.1016/j.icheatmasstransfer.2020.104645 ↗
76. Comparing the performance of neural networks developed by using Levenberg-Marquardt and Quasi-Newton with the gradient descent algorithm for modelling a multiple response grinding process10.1016/j.eswa.2011.08.087 ↗
77. Prediction of wear behaviors of nickel free stainless steel-hydroxyapatite bio-composites using artificial neural network10.1016/j.commatsci.2009.09.019 ↗
78. Optimization of hematite and quartz BIOFLOTATION by AN artificial neural network (ANN)10.1016/j.jmrt.2019.02.022 ↗
79. The feasibility of Levenberg–Marquardt algorithm combined with imperialist competitive computational method predicting drag reduction in crude oil pipelines10.1016/j.petrol.2019.106634 ↗
80. Prediction of clad characteristics using ANN and combined PSO-ANN algorithms in laser metal deposition process10.1016/j.surfin.2020.100699 ↗
81. Estimating strength properties of geopolymer self-compacting concrete using machine learning techniques10.1016/j.jmrt.2020.06.008 ↗
82. A unique thermal conductivity model ( ANN ) for nano fl uid based on experimental study10.1016/j.powtec.2020.09.011 ↗
83. Garza-Ulloa · 2018