journal article·2019-01

Preparation and properties of ultra-fine-grained and nanostructured copper alloy with the addition of P

Litao Han, Jianwei Liu, Huaguo Tang, Xianfeng Ma, Wei Zhao

Publisher page

Abstract

Abstract In this paper, the high performance Cu-Fe-P alloys with ultra-fine grain and nanocrystalline structure were successfully prepared by mechanical alloying (MA) and reactive hot-pressing (RHP). Then the combined effects of sintering temperature and phosphorus content on microstructure and properties were investigated. The results showed that phosphorus had a positive effect on the performance of Cu-Fe-P alloy. It could reduce the content of iron doped in the Cu matrix rather than forming precipitates such as Fe3P or Fe2P. Moreover, the ultra-fine grain and nanocrystalline structure had a great effect on performance of the alloys. The crystallite size of the Cu-Fe-P alloys exhibited average value of 10 nm after milling for 4 h by TEM. The lower sintering temperature was better to retain the size of nanoparticles and achieve excellent performance. Consequently, the best performance was achieved by the Cu-Fe-0.025P sintered at 600 °C and ball-milled for 4 h. The electrical conductivity reached 80.41% IACS with the tensile strength of 517 MPa which was much better than the conventional Cu-Fe-P alloy.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Aluminum Alloys Composites Properties · Advanced materials and composites · Microstructure and mechanical properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (42)

Show source-provided references
1. Copper and copper alloys
2. Microstructure and properties of Cu–2.3Fe–0.03P alloy during thermomechanical treatments10.1016/S1003-6326(15)63757-8 ↗
3. Effect of boron and cerium on microstructures and properties of Cu-Fe-P alloy10.1016/S1002-0721(06)60172-5 ↗
4. Study of rare earth elements on the physical and mechanical properties of a Cu–Fe–P–Cr alloy10.1016/j.mseb.2007.10.011 ↗
5. Effect of boron and cerium on corrosion resistance of Cu-Fe-P alloy10.1007/s11665-016-1918-6 ↗
6. Theoretical study of particle dissolution during homogenization in Cu–Fe–P alloy10.3390/met8060455 ↗
7. Effect of Ag on the microstructure and properties of Cu–Fe in situ composites10.1016/j.scriptamat.2005.07.028 ↗
8. Effect of thermomechanical processing on the microstructure and properties of a Cu-Fe-P alloy10.1007/s11665-014-1352-6 ↗
9. Nanocrystalline materials10.1016/0079-6425(89)90001-7 ↗
10. Pinning of grain boundaries by second phase particles in equal-channel angularly pressed Cu–Fe–P alloy10.1016/j.msea.2006.05.081 ↗
11. The synthesis and structure of nanocrystalline materials produced by mechanical attrition: a review10.1016/0965-9773(93)90016-5 ↗
12. Structure and properties of ultrafine-grained materials produced by severe plastic deformation10.1016/0921-5093(93)90717-S ↗
13. Achieving superplasticity in ultrafine-grained copper: influence of Zn and Zr additions10.1016/S0921-5093(02)00868-7 ↗
14. Structural, optical and photocatalytic applications of biosynthesized NiO nanocrystals10.1080/17518253.2018.1447604 ↗
15. Enhanced mechanical properties of pure copper with a mixture microstructure of nanocrystalline and ultrafine grains10.1016/j.matlet.2016.09.020 ↗
16. A maximum in the strength of nanocrystalline copper10.1126/science.1086636 ↗
17. A bulk of uniform nanocrystalline copper with superior comprehensive mechanical properties electroformed in an ultra-low sulfate concentration bath without additives10.1016/j.msea.2017.08.031 ↗
18. Investigation on the properties of nanostructured Cu alloy prepared by mechanical milling and reactive hot-pressing10.1016/j.jallcom.2018.01.318 ↗
19. Eco-friendly preparation of zinc oxide nanoparticles using Tabernaemontana divaricata and its photocatalytic and antimicrobial activity10.1016/j.jphotobiol.2018.02.011 ↗
20. Synthesis and characterization of ZnO–CuO nanocomposites powder by modified perfume spray pyrolysis method and its antimicrobial investigation10.1088/1674-4926/39/3/033001 ↗
21. Green-fuel-mediated synthesis of self-assembled NiO nano-sticks for dual applications—photocatalytic activity on Rose Bengal dye and antimicrobial action on bacterial strains10.1088/2053-1591/aa7e3c ↗
22. Microstructure characteristic, mechanical properties and sintering mechanism of nanocrystalline copper obtained by SPS process10.1016/j.msea.2009.07.016 ↗
23. Hot deformation behavior of Cu–Fe–P alloys during compression at elevated temperatures10.1016/j.jmatprotec.2008.06.048 ↗
24. Green synthesis of NiO nanoparticles using Aegle marmelos leaf extract for the evaluation of in-vitro cytotoxicity, antibacterial and photocatalytic properties10.1016/j.jphotobiol.2018.01.023 ↗
25. An electrochemically active green synthesized polycrystalline NiO/MgO catalyst: use in photo-catalytic applications10.1016/j.materresbull.2017.09.022 ↗
26. Facile synthesis of heterostructured cerium oxide/yttrium oxide nanocomposite in UV light induced photocatalytic degradation and catalytic reduction: synergistic effect of antimicrobial studies10.1016/j.jphotobiol.2017.05.024 ↗
27. Investigation on preferably oriented abnormal growth of CdSe nanorods along (0002) plane synthesized by henna leaf extract-mediated green synthesis
28. Suryanarayana · 2004
29. Mechanical alloying and properties of immiscible Cu-20 wt.% Mo alloy10.1016/j.jallcom.2015.06.129 ↗
30. Bulk ultrafine binderless WC prepared by spark plasma sintering10.1016/j.scriptamat.2005.10.014 ↗
31. Synthesis, sintering, and mechanical properties of nanocrystalline cemented tungsten carbide – a review10.1016/j.ijrmhm.2008.07.011 ↗
32. Mechanical properties and rapid consolidation of binderless nanostructured tantalum carbide10.1016/j.ceramint.2009.06.012 ↗
33. Consolidation of binderless nanostructured titanium carbide by high-frequency induction heated sintering10.1016/j.ceramint.2010.03.007 ↗
34. Rapid sintering of ultra fine WC and WC-Co hard materials by high-frequency induction heated sintering and their mechanical properties10.1007/BF03027821 ↗
35. Reactive hot pressing of ZrB2–SiC composites10.1111/j.1151-2916.2000.tb01558.x ↗
36. Low-temperature densification of zirconium diboride ceramics by reactive hot pressing10.1111/j.1551-2916.2006.01299.x ↗
37. Preparation, microstructure and mechanical properties of bulk (W0.5Al0.5)C0.65 without binder phase by reactive hot-pressing10.1016/j.jallcom.2016.04.066 ↗
38. An investigation on morphology and structure of Cu–Cr alloy powders prepared by mechanical milling and alloying10.1016/j.powtec.2014.10.010 ↗
39. Investigation into the sintered behavior and properties of nanostructured WC–Co–Ni–Fe hard metal alloys10.1016/j.msea.2014.03.096 ↗
40. Microstructure and mechanical properties of WC-Ni-Al based cemented carbides developed for engineering applications10.3139/146.110593 ↗
41. Characterization and properties of sintered WC–Co and WC–Ni–Fe hard metal alloys10.1016/j.jallcom.2013.09.188 ↗
42. Strength and conductivity of in situ Cu-Fe alloys10.1007/BF01105700 ↗