journal article·2020-03-01Open access

Abrasive water jet machining of Sisal/Pineapple epoxy hybrid composites with the addition of various fly ash filler

K R Sumesh, K Kanthavel

Materials Research Express· Volume 7· Issue 3

Abstract

Abstract This research was based on influence of various fly ash filler content in the machining properties of Pineapple (P)/Sisal (S) hybrid fiber reinforcement composites. Fly ash from bio waste materials of Bagasse (BGFA), Banana (BFA) and Coir (CFA) were used. High hardness nature of 3% BFA (22.73 HV) and 3% CFA (23.85 HV) reduces Material Removal Rate (MRR) and increases its surface roughness nature of the composites. Maximum MRR of 376.38 mm3 min−1 was observed in 3% BGFA combinations with 250 MPa Water jet Pressure (WP), 1mm Standoff Distance (SOD) and 20 mm min−1Traverse Speed (TS) as machining parameters. MRR of 353.64 and 352.76 mm3 min−1 was found out with 1% CFA and 1% BFA combinations. Lower surface roughness of 6.39 μm, 6.71 μm and 6.75 μm was found in 3% BGFA, 1% CFA and 1% BFA based composites. Filler surface created a tight bonding with the matrix, which reduces the erosion of fiber particles at higher WP. Untreated fibers showed lesser machining properties due to low fiber/matrix bonding. SEM results showed reducing of cracks and matrix breakages by the substitution of filler powders.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Erosion and Abrasive Machining · Natural Fiber Reinforced Composites · Plant Surface Properties and Treatments

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (36)

Show source-provided references
1. Tribological and mechanical behaviours of rattan-fibre-reinforced friction materials under dry sliding conditions10.1088/2053-1591/aab4a7 ↗
2. Natural fiber-mediated epoxy composites – a review10.1016/j.compositesb.2016.06.051 ↗
3. Characterization of new natural cellulosic fiber from the perotis indica plant10.1080/1023666X.2016.1202466 ↗
4. Characterization of raw and benzoyl chloride treated impomea pes-caprae fibers and its epoxy composites10.1088/2053-1591/ab2de2 ↗
5. Characterization of new natural cellulosic fiber from cissus quadrangularis stem10.1016/j.carbpol.2014.09.072 ↗
6. Characterization of raw and alkali treated new natural cellulosic fibers from Tridax procumbens10.1016/j.ijbiomac.2018.12.056 ↗
7. Effect of the stacking sequence on vibrational behavior of sansevieria cylindrica/coconut sheath polyester hybrid composites10.1177/0731684415570683 ↗
8. Natural fibre reinforced non-asbestos organic non-metallic friction composites: effect of abaca fibre on mechanical and tribological behaviour10.1088/2053-1591/aad767 ↗
9. Mechanical and thermal properties of polylactic acid composites reinforced with cellulose nanoparticles extracted from kenaf fibre10.1088/2053-1591/3/12/125301 ↗
10. A review on mechanical behavior of natural fiber reinforced polymer composites and its applications10.1177/0731684419828524 ↗
11. The pull-out behavior of chemically treated lignocellulosic fibers / polymeric matrix interface (LF/PM ): a review10.1016/j.compositesb.2019.107059 ↗
12. A study of mechanical and morphological properties of PLA based biocomposites prepared with EJO vegetable oil based plasticiser and kenaf fibres
13. Mercerization treatment parameter effect on coir fiber reinforced polymer matrix composite10.1088/2053-1591/aad034 ↗
14. Green synthesis of aluminium oxide nanoparticles and its applications in mechanical and thermal stability of hybrid natural composites10.1007/s10924-019-01506-y ↗
15. Review on mechanical properties evaluation of pineapple leaf fibre (PALF) reinforced polymer composites10.1016/j.compositesb.2019.106927 ↗
16. Synergy of fiber content, Al2O3 nanopowder, NaOH treatment and compression pressure on free vibration and damping behavior of natural hybrid-based epoxy composites10.1007/s00289-019-02823-x ↗
17. Preparation and characterization of thermoplastic starch composites with fly ash modified by planetary ball milling10.1016/j.carbpol.2018.03.009 ↗
18. The influence of reinforcement, alkali treatment, compression pressure and temperature in fabrication of sisal/coir/epoxy composites: GRA and ANN prediction10.1007/s00289-019-02988-5 ↗
19. Influence of selected treatment on tensile properties of short pineapple leaf fiber reinforced tapioca resin biopolymer composites10.1007/s10924-018-1296-2 ↗
20. Bioalumina nano powder extraction and its applications for sisal, Coir and Banana hybrid fiber composites: mechanical and thermal properties10.1007/s10924-019-01496-x ↗
21. The pyrolysis kinetics of bagasse at low heating rates10.1016/0961-9534(93)90092-I ↗
22. Dynamic analysis of a thorium fuel cycle in CANDU reactors10.1016/j.anucene.2008.04.010 ↗
23. Mechanical and morphological properties of fly ash/epoxy composites using conventional thermal and microwave curing methods10.1016/j.compscitech.2007.01.016 ↗
24. Abrasive water jet machining and mechanical behavior of banyan tree saw dust powder loaded polypropylene green composites10.1002/pc.23348 ↗
25. Performance evaluation of abrasive water jet machining on banana fiber reinforced polyester composite10.1080/15440478.2016.1212768 ↗
26. AWJM performance of jute/polyester composite using MOORA and analytical models10.1080/10426914.2017.1279314 ↗
27. Machinablity of hybrid natural fibre composite with and without filler as reinforcement10.1080/10426914.2015.1117633 ↗
28. Abrasive water jet drilling of advanced sustainable bio-fibre-reinforced polymer/hybrid composites: a comprehensive analysis of machining-induced damage responses10.1007/s00170-018-2670-x ↗
29. AWJ machinability performance of CS/UPR composites with the effect of chemical treatment10.1080/10426914.2017.1328114 ↗
30. Thermo mechanical characterization of calotropis gigantea stem powder-filled jute fiber-reinforced epoxy composites10.1080/15440478.2017.1354740 ↗
31. Evaluation of Azadirachta indica seed/spent Camellia sinensis bio-filler based jute fabrics–epoxy composites: experimental and numerical studies10.1177/1528083718811086 ↗
32. Effect of graphene powder on banyan aerial root fibers reinforced epoxy composites10.1080/15440478.2019.1675219 ↗
33. Mechanical/thermal/vibrational properties of sisal, banana and coir hybrid natural composites by the addition of bio synthesized aluminium oxide nano powder10.1088/2053-1591/aaff1a ↗
34. Peanut oil cake-derived cellulose fiber: Extraction, application of mechanical and thermal properties in pineapple/flax natural fiber composites10.1016/j.ijbiomac.2020.02.118 ↗
35. Comprehensive characterization of sugarcane bagasse ash for its use as an adsorbent10.1007/s12155-015-9646-6 ↗
36. Effect of bagasse ash filled epoxy composites reinforced with hybrid plant fibres for mechanical and thermal properties10.1016/j.compositesb.2018.10.038 ↗