journal article·2023-09-01Open access

Picosecond laser microvia drilling of ABF material using MHz burst mode

Daniel Franz, Tom Häfner, Kay Bischoff, Jonas Helm, Tim Kunz, Stefan Rung, Cemal Esen, Ralf Hellmann

Materials Research Express· Volume 10· Issue 9

Abstract

Abstract We report on a comprehensive study of laser percussion microvia drilling of Ajinomoto build-up film (ABF) material using an ultrashort pulsed laser in MHz burst mode. After laser processing, microvia drilling quality is being evaluated by the fabricated diameter and taper using laser scanning microscopy and metallography. The influences of the incubation effect, heat accumulation and shielding effects as a result of pulse to pulse interactions are being discussed on the ablation threshold, penetration depth and laser microvia drilling quality. We find that an increasing heat accumulation in MHz burst mode processing is responsible for the void formation and delamination of the insulating ABF layer. Therefore, the parameter clearance is introduced to evaluate these effects on the microvia sidewalls. For a comparable clearance, applying 2 intra-burst pulses achieves an average reduced taper of down to 19.5% compared to single pulse mode. At the same time, a reduced laser drilling time of 16.7% per microvia highlights the enormous potential of the MHz burst mode for laser drilling of ABF material in printed circuit board fabrication.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Laser Material Processing Techniques · Advanced Surface Polishing Techniques · Advanced machining processes and optimization

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (59)

Show source-provided references
1. Study of the dynamics of material removal processes in combined pulse laser drilling of alumina ceramic10.1016/j.optlastec.2022.109053 ↗
2. Advances in laser drilling of structural ceramics10.3390/nano12020230 ↗
3. Rapid micro hole laser drilling in ceramic substrates using single mode fiber laser10.1016/j.jmatprotec.2015.02.014 ↗
4. Fiber laser cutting of alumina substrates for electronic applications comparison of the experimentally determined and simulated influence on the mechanical strength10.17265/2328-2223/2015.03.001 ↗
5. Picosecond IR pulsed laser drilling of copper-coated glass/epoxy composite10.1109/TCPMT.2017.2763127 ↗
6. Ultrashort pulsed laser drilling of printed circuit board materials10.3390/ma15113932 ↗
7. Smaller microvias for packaging interconnects by picosecond UV laser with a nanometer metal barrier layer: a feasibility study10.1109/TCPMT.5503870 ↗
8. Microdrilling of through-holes in flexible printed circuits using picosecond ultrashort pulse laser10.3390/polym10121390 ↗
9. Next generation of 2-7 micron ultra-small microvias for 2.5 D panel redistribution layer by using laser and photolithography technologies10.1109/ECTC.2019.00144 ↗
10. Innovative sub-5 μm microvias by Picosecond UV laser for post-moore packaging interconnects10.1109/TCPMT.2019.2941866 ↗
11. Solid state UV laser technology for electronic packaging applications10.1117/12.571520 ↗
12. Microdrilling machinability of organic material for semiconductor packaging by 248 nm excimer laser10.2494/photopolymer.33.499 ↗
13. Chip embedded wafer level packaging technology for stacked RF-SiP application10.1109/ECTC.2007.373814 ↗
14. Fine line routing and micro via patterning in ABF Enabled by excimer laser ablation10.4071/isom-2017-TP44_011 ↗
15. Ultra-short pulse lasers for microfabrication: a review10.1109/JSTQE.2021.3097009 ↗
16. Laser ablation and micromachining with ultrashort laser pulses10.1109/3.631270 ↗
17. Ablation of solids by femtosecond lasers: ablation mechanism and ablation thresholds for metals and dielectrics10.1063/1.1447555 ↗
18. Ultrafast lasersreliable tools for advanced materials processing10.1038/lsa.2014.30 ↗
19. Ultra-short pulsed laser manufacturing and surface processing of microdevices10.1016/j.eng.2018.10.004 ↗
20. 1 kW, 200 mJ picosecond thin-disk laser system10.1364/OL.42.001381 ↗
21. Ultrafast thulium fiber laser system emitting more than 1 kW of average power10.1364/OL.43.005853 ↗
22. High power, high energy, and high flexibility: powerful ultrafast lasers based on InnoSlab technology10.1117/12.2516968 ↗
23. 10.4 kW coherently combined ultrafast fiber laser10.1364/OL.392843 ↗
24. Femtosecond laser ablation in burst mode as a function of pulse fluence and intra-burst repetition rate10.2961/jlmn.2020.03.2014 ↗
25. Surface ablation efficiency and quality of fs lasers in single-pulse mode, fs lasers in burst mode, and ns lasers10.1016/j.apsusc.2019.144594 ↗
26. Review on experimental and theoretical investigations of ultra-short pulsed laser ablation of metals with burst pulses10.3390/ma14123331 ↗
27. Ablation characteristics on silicon from ultrafast laser radiation containing single MHz and GHz burst pulses10.1007/s00339-022-05858-6 ↗
28. Micromachining of invar foils with GHz MHz and kHz femtosecond burst modes10.3390/mi11080733 ↗
29. MHz burst mode processing as a tool for achieving removal rates scalability in ultrashort laser micro-machining10.1007/s00339-022-05864-8 ↗
30. Precision and resolution in laser direct microstructuring with bursts of picosecond pulses10.1007/s00339-017-1490-4 ↗
31. Micro processing with ultrafast bursts of pulses10.1016/j.procir.2020.09.110 ↗
32. Ablation-cooled material removal with ultrafast bursts of pulses10.1038/nature18619 ↗
33. Residual heat during laser ablation of metals with bursts of ultra-short pulses10.1515/aot-2018-0003 ↗
34. In-situ analysis of ultrashort pulsed laser ablation with pulse bursts10.2961/jlmn.2019.01.0015 ↗
35. Influence of heat accumulation during laser micromachining of CoCrMo alloy with ultrashort pulses in burst mode10.1007/s00339-019-3203-7 ↗
36. Effect of pulse to pulse interactions on ultra-short pulse laser drilling of steel with repetition rates up to 10 MHz10.1364/OE.22.018790 ↗
37. High speed laser drilling of metals using a high repetition rate, high average power ultrafast fiber CPA system10.1364/OE.16.008958 ↗
38. Enhanced ablation efficiency using GHz bursts in micromachining fused silica10.1364/OL.415959 ↗
39. Laser beam micromachining (LBMM)-a review10.1016/j.optlaseng.2015.03.017 ↗
40. Plasma evolution during metal ablation with ultrashort laser pulses10.1364/OPEX.13.010597 ↗
41. Femtosecond laser ablation by bibursts in the MHz and GHz pulse repetition rates10.1364/OE.417883 ↗
42. Influence of the burst mode onto the specific removal rate for metals and semiconductors10.2351/1.5096083 ↗
43. Effects of burst mode on transparent materials processing10.1117/12.2079677 ↗
44. Modeling of multi-burst mode pico-second laser ablation for improved material removal rate10.1007/s00339-009-5405-x ↗
45. Analysis of the hole shape evolution in fs-pulse percussion drilling with bursts10.1117/12.2212801 ↗
46. Time dynamics of burst-train filamentation assisted femtosecond laser machining in glasses10.1364/OE.19.025632 ↗
47. Burst train generator of high energy femtosecond laser pulses for driving heat accumulation effect during micromachining10.1364/OL.40.002064 ↗
48. Reliability studies of excimer laser-ablated microvias below 5 micron diameter in dry film polymer dielectrics for next generation, panel-scale 2.5 D interposer RDL10.1109/ECTC.2018.00154 ↗
49. Simple technique for measurements of pulsed Gaussian-beam spot sizes10.1364/OL.7.000196 ↗
50. Generic incubation law for laser damage and ablation thresholds10.1063/1.4913282 ↗
51. Influence of the repetition rate and pulse duration on the incubation effect in multiple-shots ultrafast laser ablation of steel10.1016/j.phpro.2013.03.136 ↗
52. The effect of damage accumulation behaviour on ablation thresholds and damage morphology in ultrafast laser micro-machining of common metals in air10.1016/j.apsusc.2004.03.229 ↗
53. Role of heat accumulation on the incubation effect in multi-shot laser ablation of stainless steel at high repetition rates10.1364/OE.22.012200 ↗
54. Explore the feasibility of fabricating pure copper parts with low-laser energy by selective laser melting10.1088/2053-1591/abbd08 ↗
55. Laser metal deposition of copper on diverse metals using green laser sources10.1007/s00170-020-05117-z ↗
56. Molded interconnect substrate (MIS) technology for semiconductor packages10.1109/ECTC32862.2020.00067 ↗
57. Investigations of qualitative aspects with burst mode ablation of silicon and cemented tungsten carbide10.1007/s00339-019-2696-4 ↗
58. Laser micromachining of silicon and cemented tungsten carbide using picosecond laser pulses in burst mode: ablation mechanisms and heat accumulation10.1007/s00339-019-2755-x ↗
59. Effects of voiding on thermomechanical reliability of copper-filled microvias: modeling and simulation10.1109/TDMR.2015.2476823 ↗