Wear behaviour of friction surfaced Al-Ni and Al-SiC coatings over mild steel
Source abstract
Abstract
Abstract The friction surfacing (FS) method offers solid-state deposition of both identical and distinct coatings while avoiding a number of the issues that encompass the traditional fusion coating process. This study investigates FS for depositing aluminium based metal matrix composites (MMCs) onto AISI1018 mild steel substrates. The Al-2Si-15SiC and Al7075-15Ni MMC consumables used for the FS process were fabricated via stir casting. The FS process, optimized at 1200 rpm for Al-SiC and 1500 rpm for Al-Ni, resulted in refined microstructures and enhanced properties. Scanning electron microscopy (SEM) and energy dispersive x-ray analysis (EDAX) of the coating reveals surface with equiaxed and fine grains. The development of Al3Ni intermetallic compounds at the coating’s interface strengthens the bond by allowing the substrate and coating material to diffuse into each other. An excellent bonding strength of 147 MPa and 142 MPa is observed for the Al7075-15Ni and Al-2Si-15SiC coating deposits, respectively. In comparison to MMC consumable rods, the FS composite coating delivers 80%–85% reduction in grain size and enhances hardness. Vickers microhardness tests showed substantial hardness increases, with Al-Ni coatings reaching 183 HV. Wear tests indicated that Al-Ni coatings outperformed Al-SiC coatings and the steel substrate, exhibiting lower wear rates and friction coefficients. This research underscores FS’s effectiveness in improving the properties of aluminium MMC coatings on mild steel, with Al-Ni coatings showing exceptional wear resistance and bond strength for industrial applications.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: Aluminum Alloys Composites Properties · Metal and Thin Film Mechanics · Electronic Packaging and Soldering Technologies
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (52)
Show source-provided references
1. Wear characteristic of TiC coated AISI 1020 mild steel fabricated by TIG cladding method10.1016/j.matpr.2020.02.466 ↗
2. Wear characteristics of Ni-WC powder deposited by using a microwave route on mild steel: microwave cladding of Ni-WC10.4018/IJSEIMS.2020010104 ↗
3. Effect of reinforcements on hardness and wear behaviour of the AISI 630 steel & fabrication of hybrid surface composite using GTA10.1080/00084433.2023.2171676 ↗
4. Wear and corrosion resistance of Cr2O3%-40% TiO2 coating on gray cast-iron by plasma spray technique10.1088/2053-1591/ab2fb7 ↗
5. Tribological behavior of Al-SiC metal matrix composite under dry, aqueous and alkaline medium10.1007/s12633-016-9504-y ↗
6. Influence of silicon carbide and porcelain on tribological performance of Al6061 based hybrid composites10.1016/j.triboint.2020.106514 ↗
7. Effect of stainless steel powder as reinforcement on mechanical and tribological properties of stir cast zn-al alloy10.1088/1757-899X/1059/1/012029 ↗
8. Friction and wear properties of short time heat-treated and laser surface re-melted NiCr-WC composite coatings at various dry sliding conditions10.1016/j.jmrt.2022.01.124 ↗
9. Effect of nickel reinforcement on micro hardness and wear resistance of aluminium alloy Al707510.1016/j.matpr.2020.04.418 ↗
10. Formation of Al3Ni nanofibers in an Al-based metal matrix composite fabricated by reaction sintering10.1557/JMR.2004.0154 ↗
11. Study on the microstructure and high-temperature oxidation performance of β-NiAl/γ′-Ni3Al intermetallic compounds fabricated by laser metal deposition10.3390/met13081461 ↗
12. Investigation of wear behaviour of silicon carbide tool inserts and titanium nitride coated tool inserts in machining of en8 steel
13. Study of the effect of parameters in friction surfacing of monel over mild steel using linear-radial basis function model10.1016/j.matpr.2017.11.558 ↗
14. An investigation on thermo-mechanical and microstructural issues in friction surfacing of Al–Cu aluminum alloys10.1088/2053-1591/ab0635 ↗
15. On coating techniques for surface protection: a review10.3390/jmmp3010028 ↗
16. Thin-film coating methods: a successful marriage of high-quality and cost-effectiveness-a brief exploration10.3390/coatings12081115 ↗
17. Hard coatings for cutting applications: physical vs. chemical vapor deposition and future challenges for the coatings community10.1016/j.surfcoat.2021.127949 ↗
18. Active corrosion protection of AA2024 aluminum alloy by sol-gel coating containing inhibitor-loaded mesoporous SBA-1510.1016/j.porgcoat.2022.107166 ↗
19. Research and progress of laser cladding on engineering alloys: a review10.1016/j.jmapro.2021.03.061 ↗
20. Overview of cold spray coatings applications and comparisons: a critical review10.1108/WJE-01-2019-0021 ↗
21. Friction surfacing of titanium alloy with aluminium metal matrix composite10.1179/174329409X451128 ↗
22. Performance analysis on deposition of aluminium 6063 over EN8 medium carbon steel by friction surfacing10.1016/j.matpr.2022.04.020 ↗
23. Microstructure and corrosion study on friction surfaced aluminum alloy coatings over mild steel10.3311/PPch.37018 ↗
24. Influence of rotational speed on process characteristics in friction surfacing of Ti-6Al-4V10.1080/10426914.2016.1257799 ↗
25. Influence of friction surfacing process parameters to deposit AA6351-T6 over AA5052-H32 using conventional milling machine10.1016/j.jmatprotec.2017.02.016 ↗
26. Influence of B4C powder reinforcement on coating structure, microhardness and wear in friction surfacing10.1080/10426914.2020.1772480 ↗
27. Friction surfacing mild-steel with monel and predicting the coating parameters using fuzzy logic10.1016/j.matpr.2018.05.138 ↗
28. Effect of mechtrode rotational speed on friction surfacing of AA2024 on AA1050 substrate10.1016/j.cirpj.2021.03.012 ↗
29. Evaluation of bond strength on deposition of aluminium 6063 alloy over EN24 medium carbon steel by friction surfacing using different mechtrode diameter10.1380/ejssnt.2019.83 ↗
30. Two body abrasive wear of Al-Mg-Si hybrid composites: effect of load and sliding distance10.5755/j01.ms.22.4.12688 ↗
31. Microstructural, mechanical and corrosion behaviour of Al–Si alloy reinforced with SiC metal matrix composite10.1177/0021998319856679 ↗
32. Friction surfacing of AISI 316 over mild steel: a characteriation study10.1016/j.dt.2018.03.003 ↗
33. Microstructure and wear characterization of AA2124/4wt.% B4C nano-composite coating on Ti− 6Al− 4V alloy using friction surfacing10.1016/S1003-6326(19)65033-8 ↗
34. In situ formation of Al–Al 3 Ni composites on commercially pure aluminium by friction stir processing10.1007/s00170-014-6162-3 ↗
35. Numerical analyses of underwater friction stir welding using computational fluid dynamics for dissimilar aluminum alloys10.1007/s11665-023-08824-2 ↗
36. Experimental investigation of mechanical properties in friction stir welding for butt joints with different thicknesses using response surface methodology10.1007/s12666-024-03268-1 ↗
37. Microstructure and mechanical properties of Al/steel dissimilar welds fabricated by friction surfacing assisted friction stir lap welding10.1016/j.jmrt.2019.10.046 ↗
38. Microstructure and wear mechanisms investigation on the brake pad10.1016/j.jmrt.2021.02.045 ↗
39. Investigation of the effect of Cr2O3-2% TiO2 coating on braking performance10.18245/ijaet.592144 ↗
40. Callister · 2020 · 486
41. Surface refinement of aluminum oxide by carbon-based reinforcement10.37934/aram.105.1.2840 ↗
42. Effects of oxidation layer and roughness on the fretting wear behavior of copper under electrical contact10.1088/2053-1591/ab5aaf ↗
43. Modeling and experimental investigation on friction surfacing of aluminum alloys10.1016/j.jallcom.2019.07.010 ↗
44. Synergistic approach to tribological characterization of hybrid aluminum metal matrix composites with ZrB2 and fly ash: experimental and predictive insights10.1177/09544089241255931 ↗
45. Friction stir processing of high-entropy alloy reinforced aluminum matrix composites for mechanical properties enhancement10.1016/j.msea.2020.139755 ↗
46. Improving the tribological properties of Al-7Fe-5Ni alloys via friction stir processing10.1115/1.4044727 ↗
47. Effects of friction layer characteristics on the tribological properties of Ni3Al solid-lubricating composites at different load conditions10.1088/2053-1591/aac41f ↗
48. Worn surface and subsurface layer structure formation behavior on wear mechanism of CoCrFeMnNi high entropy alloy in different sliding conditions10.1016/j.apsusc.2021.149202 ↗
49. Tribology: friction and wear of engineering materials
50. Tribological properties of friction pairs under double composite surface configuration with diamond film and laser texture10.1016/j.triboint.2023.108996 ↗
51. Effect of T6 heat treatment on mechanical and tribological properties of fabricated AA7075/ZrB2/Fly Ash hybrid aluminum metal matrix composite by ultrasonic-assisted stir casting enroute10.1007/s40962-023-01177-5 ↗
52. Effect of temperature and sliding velocity on the dry sliding wear mechanisms of boron modified Ti-6Al-4V alloys10.3390/lubricants10110296 ↗