journal article·2024-06-01Open access

Influences of preheating parameters on the quality of weld by thermite rail welding

Romadorn Burapa, Hein Zaw Oo, Wissarut Sangwiman, Prapas Muangjunburee

Materials Research Express· Volume 11· Issue 6

Abstract

Abstract The major goal of this study is to enhance the mechanical and metallurgical characteristics of rail steel grade R260 joined by thermite welding under various preheating conditions, including preheating time and gas pressure. Mainly two conditions, referred to as the Normal Condition and Improved Condition, are carried out for experiments. Prior to welding, the Normal Condition was preheated using liquefied petroleum gas (LPG) and oxygen gas pressures of 1 bar and 4.5 bar for 3 min, and the Improved Condition was preheated using liquefied petroleum gas and oxygen gas pressures of 1.2 bar and 4.5 bar for 6 min and 30 s. To investigate the mechanical and physical properties, micro-Vickers hardness tests, tensile tests and slow bending tests were also carried out. Welded metal in Normal Condition has many defects, including gas holes and shrinkage cavities. When comparing the Normal Condition to the Improved Condition, the Improved Condition demonstrates significantly more bending load and deflection. Specifically, the thermite welded rail sample of Improved Condition demonstrated a remarkable ability to endure bending loads of 108 tonnes and a deflection of 16 mm, and this sample remained unbroken until it exceeded 50% of the standardized deflection limit (10 mm). In addition, the average hardness values for the Improved Condition of the weld metal zone and the heat-affected zone were 331 HV and 289 HV, respectively. The Normal Condition produced an unsatisfactory fracture surface after slow bending test. This was caused by weld defects at the thermite weld due to inappropriate preheating.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Engineering and Environmental Studies · Railway Systems and Materials Science · Advancements in Materials Engineering

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (40)

Show source-provided references
1. Microstructure and residual stress variations in weld zone of flash-butt welded railroads10.1179/136217104225012201 ↗
2. Hardfacing of thermite welded rail by flux-cored arc welding10.1016/j.wear.2024.205314 ↗
3. Experimental and numerical investigation of the characteristics of flash-butt joints used in continuously welded rails10.1177/0954409719830189 ↗
4. Review of factors affecting stress-free temperature in the continuous welded rail track10.1016/j.egyr.2022.11.151 ↗
5. Dynamic constitutive model of U75VG rail flash-butt welded joint and its application in wheel-rail transient rolling contact simulation10.1016/j.engfailanal.2022.106078 ↗
6. Fatigue crack growth in a welded rail under the influence of residual stresses10.1016/j.engfracmech.2004.04.009 ↗
7. An experimental investigation on flash butt welded rails10.1016/j.engfailanal.2015.07.009 ↗
8. Fatigue behavior and microstructural characterization of a high strength steel for welded railway rails10.1016/j.ijfatigue.2018.07.032 ↗
9. O’Brien · 2007 · 573
10. Numerical investigation of the cooling stage during aluminothermic welding of rails: rapid welding process without preheating10.1016/j.tsep.2022.101610 ↗
11. Satish · 2013 · 303
12. Optimization of thermit welding
13. Improvement in mechanical behavior of expulsion with heat treated thermite welded rail steel
14. The thermomechanical modeling of aluminothermic welds affected by different defects
15. Mechanical properties and microstructural analysis of rail thermite welding joints10.1109/ICIRT.2018.8641675 ↗
16. Damage tolerance investigations on rails10.1016/j.engfracmech.2008.04.001 ↗
17. Welding for the Railroad Industry
18. Heat transfer modelling of rail thermite welding10.1243/09544097F01505 ↗
19. EN 14730-1-2017 · 2017
20. ASTM E407-2015 · 2016
21. BS 427-1990 · 1990
22. ASTM E8/E8M-11 · 2011
23. Investigation of cause and prevention measures against surface defects on thermit welds10.2219/rtriqr.57.2_112 ↗
24. The mechanical properties of thermite welds in premium alloy rails10.1016/0025-5416(84)90159-9 ↗
25. Structure and properties of thermite welds in rails
26. Microstructural evolutions and impact toughness in simulated welding heat affected zones for a high-strength carbide-free bainitic rail steel10.1016/j.msea.2023.145325 ↗
27. Nonproportionally multiaxial cyclic plastic deformation of U75 rail steel: experiment and modeling10.1016/j.ijfatigue.2022.107480 ↗
28. Characterization of deformed pearlitic rail steel10.1088/1757-899X/219/1/012035 ↗
29. Investigation on material characteristics and fatigue crack behavior of thermite welded rail joint10.1016/j.conbuildmat.2021.122249 ↗
30. Consequences of thermite welding on the microstructure of the heat affected zone of a carbide-free bainitic steel rail10.1016/j.jmapro.2023.11.027 ↗
31. Improving microstructure and hardness of softening area at HAZ of thermite welding on rail running surface10.1016/j.mtcomm.2023.105485 ↗
32. Microstructural and mechanical characterization of postweld heat-treated thermite weld in rails10.1016/S1044-5803(99)00006-6 ↗
33. Analysis of damaged rail weld10.2219/rtriqr.44.59 ↗
34. Finite element modeling of the aluminothermic welding with internal defects and experimental analysis10.1051/matecconf/20120100002 ↗
35. Failure modes in aluminothermic rail welds under high axle load conditions10.1016/j.engfailanal.2003.05.003 ↗
36. Inspecting welds in rail
37. Weld defect formation in rail thermite welds10.1243/0954409JRRT44 ↗
38. Structural fatigue investigation of thermite welded rail joints considering weld-induced residual stress and stress relaxation by cyclic load10.1016/j.engstruct.2021.112033 ↗
39. Fatigue performance of weldbonded high strength sheet steels tested in Arctic, room temperature and tropical environments10.1016/S0143-7496(99)00064-0 ↗
40. Experimental study of mechanical behavior and microstructural benchmarking between the rail and the thermite weld