journal article·2024-09-01Open access

Evaluation of wear resistance of CrN, CrAlN, and TiAlN coatings deposited by multi-arc ion plating on spinning die of Cr12MoV

Rongchuan Lin, Shilong Sun, Bin You, Tianlei Dong, Yusheng Sui, Shasha Wei

Materials Research Express· Volume 11· Issue 9

Abstract

Abstract This study successfully deposited CrN, CrAlN, and TiAlN coatings on the surface of Cr12MoV substrate using multi-arc ion plating (MAIP). The influence of phase composition and surface morphology on the hardness, adhesion strength, friction performance, and wear mechanisms of these coatings was investigated, with a comparative analysis of their wear resistance. Nanoindentation results revealed that the hardness (H) of CrN, CrAlN, and TiAlN coatings increased by 70.37%, 74.97%, and 75.64%, respectively, compared to the substrate. The hardness (H) and elastic modulus (E) were found to be positively correlated. CrAlN demonstrated superior resistance to deformation, reflected in its higher H/E and H 3 /E 2 radios compared to the CrN and TiAlN. Adhesion tests showed that CrAlN had the strongest adhesion strength to the substrate, with an adhesion force of 81.55 N, representing a 14.78% and 8.46% improvement over CrN and TiAlN, respectively. Friction and wear tests identified CrAlN as having the lowest friction coefficient (0.389), attributed to its high hardness and strong adhesion. The wear mechanisms of CrAlN observed were primarily mild abrasive wear, oxidative wear, and adhesive wear. In comparison, CrN and TiAlN coatings exhibited higher friction coefficients of 0.424 and 0.391, respectively, due to their lower hardness and adhesion, which led to more severe oxidative and abrasive wear. Additionally, the TiAlN coating showed signs of brittle failure in wear scars, likely due to the formation of Al2O3 oxides during wear.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Metal and Thin Film Mechanics · Diamond and Carbon-based Materials Research · Advanced materials and composites

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (44)

Show source-provided references
1. An approach to optimize cooling channel parameters of Low pressure Die casting process for reducing shrinkage porosity in Aluminium alloy wheels10.1016/j.matpr.2022.03.478 ↗
2. Effect of Al–5Ti–1B–La intermediate alloy on microstructure and mechanical properties of A356.2 aluminum alloy10.1016/j.jmrt.2024.03.144 ↗
3. Casting and spinning aluminum alloy wheel fatigue properties and life prediction study10.1111/ffe.14085 ↗
4. Plastic flow instability under compressive loading during shear spinning process10.1115/1.3185791 ↗
5. A review of spinning, shear forming and flow forming processes10.1016/S0890-6955(03)00172-X ↗
6. A review of the mechanics of metal spinning10.1016/j.jmatprotec.2009.08.021 ↗
7. Fluid mechanics of spin casting of metals10.1146/annurev.fluid.29.1.373 ↗
8. Analysis and modelling of a rotary forming process for cast aluminium alloy A35610.1016/j.jmatprotec.2015.06.036 ↗
9. Synthesis of two-dimensional WS2/nickel nanocomposites via electroforming for high-performance micro/nano mould tools10.1016/j.surfcoat.2022.128351 ↗
10. Surface morphological evolution and microhardness change of Cr12MoV steel by pulsed laser polishing10.1016/j.optlastec.2023.110419 ↗
11. Characteristic and tribological behavior of amorphous carbon–containing CrAlCN coating by cathodic arc ion plating10.1016/j.ijrmhm.2023.106372 ↗
12. (Cr, Me)N coatings deposited in a vacuum furnace by magnetron sputtering of a ferrochromium alloy10.1016/j.jmatprotec.2004.09.064 ↗
13. Structure and tribological properties of multiphase carbon coatings fabricated by multi-arc ion plating10.1016/j.surfcoat.2023.130319 ↗
14. Microstructure and properties of CrN coating via multi-arc ion plating on the valve seat material surface10.1016/j.jallcom.2021.161966 ↗
15. PVD coatings as an environmentally clean alternative to electroplating and electroless processes10.1016/S0257-8972(99)00145-0 ↗
16. A comparison of the galling wear behaviour of PVD Cr and electroplated hard Cr thin films10.1016/j.surfcoat.2018.06.070 ↗
17. An analysis on tribological performance of CrCN coatings with different carbon contents in seawater10.1016/j.triboint.2015.07.002 ↗
18. Microstructure, electrochemical and tribocorrosion behaviors of CrCN nanocomposite coating with various carbon content10.1016/j.surfcoat.2021.126997 ↗
19. Wear behaviour of PVD coating strengthened WC-Co cutters during milling of oak-wood10.1016/j.wear.2022.204336 ↗
20. Adhesion-induced demolding forces of hard coated microstructures measured with a novel injection molding tool10.3390/polym15051285 ↗
21. Tribological oxidation behaviour of PVD hard coatings10.1016/j.triboint.2009.04.026 ↗
22. Sliding wear of CrN, AlCrN and AlTiN coated AISI H13 hot work tool steels in aluminium extrusion10.1016/j.triboint.2012.07.023 ↗
23. Performance evaluation of CrAlN and TiAlN coatings deposited by HiPIMS in micro drilling of a Ni-based superalloy10.1016/j.surfcoat.2022.128980 ↗
24. Shanghai Tool Works Co., Ltd JB/T 7707-1995 Test Method for Ion Plating Hard Film Thickness · 1995 · 1
25. Association · 1992 · 7
26. Fabrication of CrAlN nanocomposite films with high hardness and excellent anti-wear performance for gear application10.1016/j.surfcoat.2010.04.014 ↗
27. A Morphological Study and Effect of Intermediate Phase Formation on Hard and Wear Resistant SiC-Co Composite Coating on Low Carbon Steel via Arc Based Heat Source10.1007/s11665-024-09629-7 ↗
28. Cathode spot erosion and ionization phenomena in the transition from vacuum to atmospheric pressure arcs10.1063/1.1663222 ↗
29. The scherrer formula for x-ray particle size determination10.1103/PhysRev.56.978 ↗
30. Effect of mould roughness on injection moulded poly (methyl methacrylate) surfaces: roughness and wettability10.1016/j.jmapro.2019.10.024 ↗
31. Wear of mold surfaces: interfacial adhesion in precision glass molding10.1016/j.wear.2023.204847 ↗
32. Microstructure and tribological properties of CrAlTiN coating deposited via multi-arc ion plating10.1016/j.mtcomm.2022.103136 ↗
33. Effect of bias voltage on the tribocorrosion performance of TiAlSiN coatings on FH790 steel by arc ion plating10.1016/j.surfcoat.2022.129177 ↗
34. Fabrication of multiscale structured hydrophobic NiCrZrN coating with high abrasion resistance using multi-arc ion plating10.1016/j.jallcom.2019.152140 ↗
35. Synthesis of nitrogen incorporated carbon films by plasma immersion ion implantation and deposition10.1016/j.surfcoat.2004.04.040 ↗
36. Elastic relationships in layered composite media with approximation for the case of thin films on a thick substrate10.1063/1.339082 ↗
37. Thermal stresses in elastic multilayer systems10.1016/S0040-6090(02)00699-5 ↗
38. Influence of phase transformation on the damage tolerance of Ti-Al-N coatings10.1016/j.vacuum.2018.06.001 ↗
39. Assessing the elastic parameters and energy-dissipation capacity of solid materials: a residual indent may tell all10.1016/j.actamat.2005.06.031 ↗
40. Friction mechanism in the running-in stage of copper: from plastic deformation to delamination and oxidation10.1016/j.triboint.2017.05.027 ↗
41. Micro and macro-tribology behavior of a hierarchical architecture of a multilayer tan/ta hard coating10.3390/coatings10030263 ↗
42. Structure, mechanical and thermal properties of Y-doped CrAlN coatings10.1016/S1003-6326(21)65689-3 ↗
43. Effects of Al, Ti, and Cr content with different interlayer configurations on tribological behavior of AlCrN and AlTiN multilayer coatings10.1177/14644207221124588 ↗
44. Effect of Al content on the hardness and thermal stability study of AlTiN and AlTiBN coatings deposited by HiPIMS10.1016/j.surfcoat.2021.127513 ↗