journal article·2024-04-01Open access

Experimental investigation of the impact of GMAW welding parameters on the mechanical properties of AISI 316L/ER 316L using quaternary shielding gas

Samir Khrais, Hadeel Al Hmoud, Ahmad Abdel Al, Tariq Darabseh

Materials Research Express· Volume 11· Issue 4

Abstract

Abstract In this study, the parameters of Metal Inert Gas (MIG) and Metal Active Gas (MAG) were investigated of AISI 316L/ER 316L. A quaternary shielding gas mixture consisting of Argon (Ar), Helium (He), Carbon Dioxide (CO2), and Nitrogen (N2) was chosen. The Taguchi orthogonal array (OA-L9) methodology was employed to explore optimal welding settings, including arc current (120A, 160A, 200A), wire feed rate (3, 3.5, 4 m min−1), and shielding gas combination (G1, G2, G3). The findings highlighted the importance of shielding gas in influencing the ultimate tensile strength (UTS), elongation percentage (EL%), and material toughness of welding joints. Notably, the highest UTS (515.77 MPa), EL% (20.85%), and material toughness (133J) were achieved by the specific group gas combination shown as G1. It is recommended to configure welding parameters to an arc current of 160A, a wire feed rate of 4 m min−1, and the G1 gas combination. Welded specimens using a G1 gas mixture showcased the best UTS and EL%. Additionally, it was found that the fusion zone (FZ) and heat-affected zone (HAZ) hardness are most profoundly influenced by the choice of gas combination (G2), resulting in the best hardness values of 253.79 HV and 239.68 HV, respectively. The optimal parameters for achieving the desired material hardness were precisely identified as (120A, 3 m min−1, G2). These insights offer a pathway to enhance welding performance and, in turn, elevate the quality and efficiency of industrial applications.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Welding Techniques and Residual Stresses · Metal and Thin Film Mechanics · Hydrogen embrittlement and corrosion behaviors in metals

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (53)

Show source-provided references
1. Heat source modeling, penetration analysis and parametric optimization of super spray MAG welding
2. A new insight on phased array ultrasound inspection in MIG/MAG welding10.3390/ma15082793 ↗
3. Effect of pulse mode and frequency on microstructure and properties of 2219 aluminum alloy by ultrahigh-frequency pulse metal-inert gas welding10.1016/j.jmrt.2022.08.094 ↗
4. Numerical analysis of the deformation behavior of 2205 duplex stainless steel TIG weld joint based on the microstructure and micro-mechanical properties10.1016/j.msea.2021.141303 ↗
5. Effects of shielding gas composition on arc behaviors and weld formation in narrow gap tandem GMAW10.1007/s00170-017-9990-0 ↗
6. Advanced gas metal arc welding processes10.1007/s00170-012-4513-5 ↗
7. Influence of shielding gases in the welding of metals10.1007/s00170-012-4111-6 ↗
8. Droplet transfer and weld formation of MIG welding with Ar-he alternating gas for aluminum alloy10.1016/j.jmapro.2019.11.012 ↗
9. Effects of shielding gas control: welded joint properties in GMAW process optimization10.1007/s00170-016-8936-2 ↗
10. Performance of weld bead profile during A-TIG welding on nitrogen alloyed stainless steel10.1088/2631-8695/ac3770 ↗
11. Automatic TIG welding of austenitic stainless steels in nitrogen and nitrogen-based gas mixtures10.3989/revmetalmadrid.0962 ↗
12. Effect of heat input on geometry of austenitic stainless steel weld bead on low carbon steel10.1007/s40032-018-0461-7 ↗
13. Effect of shielding gases on microstructure and mechanical properties of super austenitic stainless steel by hybrid welding10.1016/j.matdes.2011.06.065 ↗
14. Effect of shielding gas on the metal transfer and weld morphology in pulsed current MAG welding of carbon steel10.1016/j.jmatprotec.2018.07.003 ↗
15. Heat input and shielding gas effects on the microstructure, mechanical properties and pitting corrosion of alternative low cost stainless steel grade 20210.1016/j.rinma.2020.100111 ↗
16. Microstructural and electrochemical evaluation of fusion welded low-nickel and 304 SS at different heat input10.1007/s11665-017-3054-3 ↗
17. Microstructure, mechanical properties and pitting corrosion of TIG weld joints alternative low-cost austenitic stainless steel grade 21610.1016/j.jajp.2020.100027 ↗
18. Effect of shielding gas composition and activating flux on the weld bead morphology of the P91 ferritic/martensitic steel10.1088/2053-1591/ab2699 ↗
19. Study of the effect of shielding gas composition on the mechanical weld properties of steel ST 37-2 in gas metal arc welding10.1016/j.matdes.2009.03.031 ↗
20. Gas metal arc welding of high nitrogen stainless steel with Ar–N2-O2 ternary shielding gas10.1016/j.dt.2020.05.021 ↗
21. Dissimilar welding of high nitrogen stainless steel and low alloy high strength steel under different shielding gas composition: Process, microstructure and mechanical properties10.1016/j.dt.2022.10.010 ↗
22. Parametric optimization of gas metal arc welding process by PCA based taguchi method on austenitic stainless steel AISI 316L10.1016/j.matpr.2017.11.255 ↗
23. Impact of gas metal arc welding parameters on bead geometry and material distortion of AISI 316L10.3390/jmmp7040123 ↗
24. Grey-based taguchi method for multi-weld quality optimization of gas metal arc dissimilar joining of mild steel and 316 stainless steel10.1016/j.rineng.2023.100963 ↗
25. Parametric optimization of MIG welding on 316L austenitic stainless steel by grey-based taguchi method10.1016/j.protcy.2016.08.204 ↗
26. Microstructural characteristics on bead on plate welding of AISI 904 L super austenitic stainless steel using gas metal arc welding process10.4314/ijest.v2i6.63710 ↗
27. Effect of shielding gas on welding performance and properties of duplex and superduplex stainless steel welds10.1007/s40194-014-0199-7 ↗
28. Process parameter optimization of gas metal arc welding on IS:2062 mild steel using response surface methodology10.1016/j.jmapro.2016.12.016 ↗
29. Microstructure, mechanical and electrochemical evaluation of dissimilar low Ni SS and 304 SS using different filler materials10.1590/1980-5373-mr-2017-0203 ↗
30. Effect of welding speed on microstructures, mechanical properties and corrosion behavior of GTA-welded AISI 201 stainless steel sheets10.1016/j.jmatprotec.2013.09.025 ↗
31. Measurement of the bead profile and microstructural characterization of a CO2 laser welded AISI 904 L super austenitic stainless steel10.1016/j.optlastec.2010.01.015 ↗
32. Prediction of bead geometry parameters in MIG welded stainless steel 409L plates by mathematical modelling10.1016/j.matpr.2020.10.795 ↗
33. Optimization of cooling conditions and cutting parameters during hard milling of AISI H13 steel by using taguchi method10.1109/amcon.2018.8615057 ↗
34. Effect of heat input on microstructure and mechanical properties of dissimilar joints of AISI 316l steel and API X70 high-strength low-alloy steel10.1016/S1006-706X(18)30024-4 ↗
35. Optimization of parameters involved in robotic MIG welding process based on quality responses10.1088/1757-899X/402/1/012016 ↗
36. Experimental investigation of effect of welding parameters on surface roughness, micro-hardness and tensile strength of AISI 316L stainless steel welded joints using 308L filler material by TIG welding10.1016/j.jmrt.2022.09.016 ↗
37. Weldability of austenitic stainless steel by metal arc welding with different shielding gas10.1016/j.prostr.2016.06.437 ↗
38. Experimental comparison between aircraft fuel tank inerting processes using NEA and MIG10.1016/j.cja.2018.04.016 ↗
39. Numerical simulation and experimental verification of droplet transfer during local dry underwater MIG welding process of SUS30410.1016/j.jmrt.2022.10.040 ↗
40. Microstructure, micro-hardness and impact toughness of welded austenitic stainless steel 316L10.1007/s12666-018-1362-4 ↗
41. Charpy impact energy correlation with fracture toughness for low alloy structural steel welds10.1016/j.tafmec.2021.102934 ↗
43. A review on the advance of low-temperature toughness in pipeline steels10.1016/j.jmrt.2023.07.119 ↗
44. Metallurgical, fatigue and pitting corrosion behavior of AISI 316 joints welded with Nb-based stabilized steel filler10.1007/s11661-019-05623-0 ↗
45. Effect of heat input on the microstructure and mechanical properties of gas tungsten arc welded AISI 304 stainless steel joints10.1016/j.matdes.2011.02.017 ↗
46. Effect of the H 2 content in shielding gas on the microstructure and oxidation resistance of Fe−15.7 wt% Cr−8.5 wt% Mn steel GTA welds10.1016/j.jmatprotec.2019.01.004 ↗
47. Effect of welding variables on mechanical properties of low carbon steel welded joint10.14743/apem2014.4.186 ↗
48. Effect of shielding gases on mechanical and metallurgical properties of duplex stainless-steel welds10.1007/s10853-008-3098-8 ↗
49. Effect of the addition of nitrogen through shielding gas on tig welds made homogenously and heterogeneously on 300 series austenitic stainless steels
50. Microstructural transformations of Dissimilar austenite-ferrite stainless steels welded joints
51. Studies on metallurgical and impact toughness behavior of variably sensitized weld metal and heat affected zone of AISI 304L welds10.1016/j.matdes.2015.09.145 ↗
52. Secondary austenite precipitation during the welding of duplex stainless steels10.4028/www.scientific.net/MSF.869.562 ↗
53. Transformation and precipitation reactions by metal active gas pulsed welded joints from X2CrNiMoN22-5-3 duplex stainless steels10.3390/ma9070606 ↗