journal article·2024-02-01Open access

Effect of heat treatment on microstructural characteristics and mechanical properties of hypereutectic B390 aluminium alloys modified by phosphorus and bismuth

Porawit Jiandon, Sukangkana Talangkun, Kowit Ponhan

Materials Research Express· Volume 11· Issue 2

Abstract

Abstract This study investigated the effects of solution treatment and aging processes on microstructural characteristics and mechanical properties of hypereutectic B390 Al-Si Alloy modified by phosphorus (P) and bismuth (Bi). The morphology evolution of primary Si, eutectic Si, intermetallic compounds, and secondary dendrite arm spacing (SDAS) of both initial and modified alloys were investigated in as-cast and heat-treated conditions. It was found that the combination of 0.1 wt%P and 0.5 wt%Bi in B390 alloy resulted in a remarkable modification and refinement of primary Si, eutectic Si, and SDAS compared to initial specimens in the as-cast condition. After heat treating, the fine lamellar eutectic Si and intermetallic compounds underwent a higher degree of fragmentation and coarsening, appearing as small round particles, leading to a more pronounced formation of a supersaturated solid solution. Additionally, the peak aging time of the B390-P-Bi alloy was only 7 h, 2 h less than the initial specimen. After T6 treatment and addition of both 0.1 wt%P and 0.5 wt%Bi, the B390-P-Bi alloy exhibited a smaller rounded Mg3Bi2 phase at peak aging with a 62.07% size reduction compared to the B390-Bi alloy. The results show that adding P with Bi enhanced hardness, ultimate tensile strength (UTS) and elongation because of refinement of the SDAS, primary Si and eutectic Si. These refinements played a crucial role in increasing tensile strength by more effective strengthening through precipitation and grain size reduction. The B390-P-Bi alloy is a promising choice for applications requiring a balance between strength and ductility.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Aluminum Alloy Microstructure Properties · Aluminum Alloys Composites Properties · Bauxite Residue and Utilization

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (52)

Show source-provided references
1. Modification effect of Sr on the microstructures and mechanical properties of Al–10.5 Si–2.0 Cu recycled alloy for die casting10.1016/j.msea.2011.10.076 ↗
2. Crystallisation characteristics of primary silicon particles in cast hypereutectic Al–Si alloy10.1179/1743133612Y.0000000040 ↗
3. Microstructure and wear behavior of in situ hypereutectic Al–high Si alloys produced by selective laser melting10.1016/j.matdes.2016.03.053 ↗
4. Effect of rare earth cerium addition on the microstructure and tensile properties of hypereutectic Al–20% Si alloy10.1016/j.jallcom.2013.02.016 ↗
5. Effect of P and Sr complex modification on Si phase in hypereutectic Al–30Si alloys10.1016/j.matdes.2012.12.054 ↗
6. A novel Zn-Cu-P master alloy and its modification performance on primary Si of A390 alloy10.1016/j.rinp.2018.12.064 ↗
7. Effect of phosphorus and heat treatment on microstructure of Al-25% Si alloy10.1007/s41230-017-5130-6 ↗
8. The influence of various Mg contents on the microstructures, mechanical properties and thermal expansion behaviors of P-modified Al–50Si alloys10.1007/s10854-019-02298-6 ↗
9. Formation mechanism and conditions of fine primary silicon being uniformly distributed on single αAl matrix in Al-Si alloys10.1016/j.matdes.2020.108853 ↗
10. Synthesis of a novel Zn–7Fe–3P master alloy and its modifying performance on primary Si in A390 alloy10.1016/j.matlet.2021.129367 ↗
11. Comparison among chemical and electromagnetic stirring and vibration melt treatments for Al–Si hypereutectic alloys10.1016/j.jallcom.2006.09.039 ↗
12. Revealing heterogeneous nucleation of primary Si and eutectic Si by AlP in hypereutectic Al-Si alloys10.1038/srep25244 ↗
13. Flake-fibrous transition of silicon in near-eutectic Al-11.7 Si-1.8 Cu-0.8 Zn-0.6 Fe-0.3 Mg alloy treated with combined effect of bismuth and strontium10.1016/j.jallcom.2015.10.074 ↗
14. Effects of individual and combined additions of Pb, Bi, and Sn on the microstructure and mechanical properties of Al-10.8 Si-2.25 Cu-0.3 Mg alloy10.1007/s11661-008-9692-1 ↗
15. A new approach to assess the effects of Sr and Bi interaction in ADC12 Al–Si die casting alloy10.1016/j.tca.2013.11.001 ↗
16. Effects of Sb, Sr, and Bi on the material properties of cast Al-Si-Cu alloys produced through heated mold continuous casting10.1007/s12206-016-0218-2 ↗
17. Evaluation of the effect of Bi, Sb, Sr and cooling condition on eutectic phases in an Al–Si–Cu alloy (ADC12) by in situ thermal analysis10.1016/j.tca.2013.02.024 ↗
18. Effect of Bi addition on microstructure and mechanical properties of hypereutectic Al-17.6 Si alloy10.1088/2053-1591/ab4d34 ↗
19. The effect of Bi-Sr and Ca-Sr interactions on the microstructure and tensile properties of Al-Si-based alloys10.3390/ma9030126 ↗
20. Effects of Sn, Bi, and Pb additions on the mechanical properties and machinability of Al-11% Si-2. 25% Cu-0.3% Mg casting alloys
21. Influences of complex modification of P and RE on microstructure and mechanical properties of hypereutectic Al-20Si alloy10.1016/S1003-6326(07)60089-2 ↗
22. Effects of La–Ce addition on microstructure and mechanical properties of Al–18Si–4Cu–0.5 Mg alloy10.1016/S1003-6326(19)65066-1 ↗
23. Microstructural modification hardness and surface roughness of hypereutectic Al-Si Alloys by a combination of bismuth and phosphorus10.3390/cryst12081026 ↗
24. Improvement in as-cast strength of high pressure die-cast Al–Si–Cu–Mg alloys by synergistic effect of Q-Al5Cu2Mg8Si6 and θ-Al2Cu phases10.1016/j.msea.2020.140612 ↗
25. Phase precipitation in transition metal-containing 354-type alloys10.3139/146.111455 ↗
26. Chapter 5, Aluminum-Silicon Alloys
27. Microstructure and mechanical properties of hypereutectic Al-Si alloy modified with Cu-P10.1016/S1001-0521(08)60031-5 ↗
28. ASTM E8/E8M-16a: standard test methods for tension testing of metallic materials
29. Effect of cooling rates on T6 Treatment of B390 Aluminium-Silicon Hypereutectic alloys10.1051/matecconf/201929302001 ↗
30. American Foundrymen’s Society · 1986
31. Image analysis for particle size distribution10.1038/162329b0 ↗
32. ASTM E562-19 · 2019
33. 2020
34. Effects of the liquid phase on tensile elongation of Al–Bi alloy10.1016/S0921-5093(00)00641-9 ↗
35. Surface segregation of trace element bismuth during heat treatment of aluminum10.1149/2.100203jes ↗
36. Role of bismuth on solidification, microstructure and mechanical properties of a near eutectic Al-Si alloys10.1007/s12540-014-5019-5 ↗
37. Influence of continuous casting speeds on cast microstructure and mechanical properties of an ADC14 alloy10.3390/met10050625 ↗
38. Aluminium phosphide as a eutectic grain nucleus in hypoeutectic Al-Si alloys10.1093/jmicro/dfh048 ↗
39. Constitution of binary alloys10.1149/1.2428700 ↗
40. Mechanism of the Mg3Bi2 phase formation in Pb-Free aluminum 6xxx Alloy with bismuth addition10.3390/cryst11040424 ↗
41. Experimental investigation and thermodynamic prediction of the Al–Bi–In phase diagram10.1016/j.jallcom.2016.06.262 ↗
42. Effect of the T6 heat treatment on microhardness of a directionally solidified aluminum-based 319 alloy10.1590/1980-5373-mr-2016-0961 ↗
43. Spheroidization and coarsening of eutectic Si particles in Al-Si-based alloys10.1155/2021/6678280 ↗
44. Effect of solution time in T6 heat treatment on microstructure and hardness of a directionally solidified Al–Si–Cu alloy10.1016/j.jallcom.2016.05.099 ↗
45. Strengthening precipitates and mechanical performance of Al–Si–Cu–Mg cast alloys containing transition elements10.1016/j.msea.2021.141497 ↗
46. Microstructural development and mechanical properties of interrupted aged Al-Mg-Si-Cu alloy10.1007/s11661-006-0192-x ↗
47. Phase relations and precipitation in Al–Mg–Si alloys with Cu additions10.1016/S0079-6425(03)00031-8 ↗
48. Effects of Cu content and Cu/Mg ratio on the microstructure and mechanical properties of Al–Si–Cu–Mg alloys10.1016/j.jallcom.2015.07.090 ↗
49. Spheroidization of primary Mg2Si in Al-20Mg2Si-4.5 Cu alloy modified with Ca and Sb during T6 heat treatment process10.1016/j.msea.2016.12.080 ↗
50. Effect of Q-Al5Cu2Mg8Si6 phase on mechanical properties of Al-Si-Cu-Mg alloy at elevated temperature10.1016/j.msea.2017.03.087 ↗
51. Effect of chemical composition and T6 heat treatment on the mechanical properties and fracture behaviour of Al-Si alloys for IC engine components10.2298/JMMB190510014V ↗
52. Microstructure and mechanical properties of Cast Al-Si-Cu-Mg-Ni-Cr alloys: effects of time and temperature on two-stage solution treatment and ageing10.3390/ma16072675 ↗