Wear behaviour of T4 and T6 heat treated LM28 composite reinforced with ZrO2 particles by stir casting method
Source abstract
Abstract
Abstract The current study was performed to investigate the metal alloy LM28’s wear characteristics, strengthened by fine and coarse ZrO2 were investigated after undergoing thermal treatment with T4 and T6 process. Aluminium degasification tablets were used during the stir casting liquid metallurgy process to produce the composites with less porosity. ZrO2 was employed as fine (10–30 μm) and coarse (80–120 μm) particles in a step size of 3% from 0 to 12 wt%. The traditional T4 and T6 HT process was applied to the composite materials (LM28 nZrO2). T4 heat treatment involved in elevating the composites to 450 °C for 120–180 min before quenching them into the oil and age them naturally for 8–42 days at ambient room temperature. T6 HT was performed in a routine fashion, but also underwent artificial aging at 190–240 °C for 3–7 h before normal cooling. When compared to T4 HT process and non-HT composites, the hardness of T6 HT composites gives better results against wear property. The ideal level of hardness and resistance to wear of the composite was found in T6 HT composites when tested with a pin on a disk throughout a range of sliding distances and loads. Scanning electron microscopy demonstrated that T4 HT and non-HT composites suffered more surface damage than T6 HT composites when subjected to the same load and sliding distance. Initially, material was removed by an abrasive wear process, but this shifted to an adhesive one as sliding distance increased. T6 thermal treated composites are ideal for usage in tough conditions as a result of their excellent hardness and resilience to wear.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: Aluminum Alloys Composites Properties · Advanced ceramic materials synthesis · Tribology and Wear Analysis
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (59)
Show source-provided references
1. Investigation of T4 and T6 heat treatment on the wear properties of sillimanite reinforced LM30 aluminium alloy composites10.1016/j.wear.2018.12.065 ↗
2. Heat treatment effect on the microstructure, tensile properties and dry sliding wear behavior of A356–10% B4C cast composites10.1016/j.matdes.2010.04.034 ↗
3. Hardness and wear resistance of ZrO2 nano particle reinforced Al nanocomposites produced by powder metallurgy10.1016/j.mspro.2015.06.043 ↗
4. The strain amplitude-controlled cyclic fatigue behavior of Al2O3 fiber reinforced Al–Si alloy composite at elevated temperatures10.1016/j.pnsc.2012.03.009 ↗
5. The effects of Mg amount on the microstructure and mechanical properties of Al–Si–Mg alloys10.1016/j.matdes.2013.04.089 ↗
6. Mechanical and tribological behaviour of Al-ZrO2 composites: a review10.1007/978-981-13-6469-3_20 ↗
7. Effect of T6 heat treatment on the microstructure, tensile properties sand fracture behavior of the modified A356 alloys10.1016/j.matdes.2011.11.018 ↗
8. Effect of T6 heat treatment on the mechanical properties of gravity die cast A356 aluminium alloy10.3923/jas.2011.2048.2052 ↗
9. Mechanical characterization of AA7068-ZrO2 reinforced metal matrix composites10.1016/j.matpr.2017.02.196 ↗
10. Age-hardening behavior of cast Al–Si base alloy10.1016/j.matlet.2003.12.027 ↗
11. The properties and microstructure of Al-based composites reinforced with ceramic particles10.1016/S0921-5093(97)00830-7 ↗
12. Precipitation behavior and mechanical performances of A356 alloy treated by Alesrela composite refinement-modification agent10.1016/j.jallcom.2019.153370 ↗
13. The effect of a T6 heat treatment on the fretting wear of a SiC particle-reinforced A356 aluminum alloy matrix composite10.1016/S0043-1648(99)00328-2 ↗
14. Influence of heat treatments on the wear behaviour of an AA6092/SiC25p composite10.1016/S0043-1648(03)00389-2 ↗
15. The aging behavior of SiC/Gr/6013Al composite in T4 and T6 treatments10.1016/j.msea.2007.11.142 ↗
16. Investigation of T4 and T6 heat treatment on the wear properties of sillimanite reinforced LM30 aluminium alloy composites10.1016/j.wear.2018.12.065 ↗
17. Effect of heat treatment on mechanical and tribological properties of aluminium metal matrix composites10.1177/0954406220922253 ↗
18. Effect of copper addition on wear and corrosion behaviours of Mg2Si particle reinforced composites10.1016/j.matdes.2011.11.052 ↗
19. Dry sliding wear behavior of heat treated hybrid metal matrix composite using Taguchi techniques10.1016/j.matdes.2014.06.007 ↗
20. Influence of SiC and Al2O3 particulate reinforcement and heat treatments on mechanical properties and damage evolution of Al-2618 metal matrix composites10.1023/A:1017591117670 ↗
21. Comparative measurements of physical and mechanical properties of AA6082 based composites reinforced with B4C and SiC particulates produced via stir casting10.1007/s12540- 020-00666-0 ↗
22. Microstructural evolution of hybrid aluminium matrix composites reinforced with SiC nanoparticles and graphene/graphite prepared by powder metallurgy10.1016/j.pnsc.2020.01.024 ↗
23. Evolution of physical and mechanical properties of Al5083/B4C composites fabricated through stir casting10.1016/j.matpr.2020.01.074 ↗
24. Some studies on mechanical and machining characteristics of Al2219/nB4C/MoS2 nano-hybrid metal matrix composites10.1016/j.measurement.2017.05.003 ↗
25. Analysis of dry sliding wear behaviour of Al6061/SiC/Al2O3 hybrid metal matrix composites10.1016/j.compositesb.2013.04.051 ↗
26. The strain amplitude-controlled cyclic fatigue behavior of Al2O3 fiber reinforced Al–Si alloy composite at elevated temperatures10.1016/j.pnsc.2012.03.009 ↗
27. Effects of T4 and T6 heat treatments on the wear behaviour of WC-Reinforced Mg alloy matrix composite10.1007/s12666-020-01860-9 ↗
28. WC Reinforced Inconel 625 super alloy matrix composites10.1007/s40997-020-00357-6 ↗
29. Effect of TiB2 particles on sliding wear behaviour of Al–4Cu alloy10.1016/j.wear.2006.04.003 ↗
30. Parametric study on the dry sliding wear behaviour of AA6082–T6/TiB2 in situ composites using response surface methodology10.1007/s40430-018-1235-0 ↗
31. Effects of silicon carbide and tungsten carbide in aluminium metal matrix composites10.1007/s12633-018-0051-6 ↗
32. Dry sliding wear behaviour of AZ31/ZrO2 composites produced using a stir casting process
33. Effect of ZrO2 quantity on mechanical properties of ZrO2 reinforced aluminum composites produced by the vacuum infiltration technique10.3989/revmetalm.195 ↗
34. Effect of ZrO2 nanoparticles on the mechanical properties of aluminum-based hybrid composites
35. Mechanical and tribological properties of Al-Si alloys reinforced with ceramic particles: A review
36. Effect of heat treatment on the mechanical properties of ZrO2 reinforced aluminum matrix composites
37. Wear behavior of Al-Si alloys reinforced with ceramic nanoparticles: role of particle size and heat treatment
38. Effect of aging on the hardness and wear properties of ZrO2 reinforced aluminum composites
39. Optimization of mechanical properties in ZrO2-reinforced Al-Mg composites via T6 heat treatment
40. Tribological characterization of ZrO2-Al alloy composite under T6 heat treatment
41. Influence of ZrO2 particle size on the wear behavior of heat-treated aluminum composites
42. Comparative wear analysis of ZrO2 reinforced aluminum composites with fine and coarse particulates
43. A review on the influence of nano-ZrO2 reinforcement on aluminum matrix composites for automotive applications
44. Machining of LM13 and LM28 cast aluminium alloys: part I10.1016/j.jmatprotec.2007.05.032 ↗
45. Microstructure and mechanical behaviour of AA6082-T6/SiC/B4C- based aluminium hybrid composites10.1080/02726351.2016.1227410 ↗
46. Production and mechanical properties of Al2O3 particle reinforced 2024 aluminium alloy composites10.1016/j.jmatprotec.2004.07.068 ↗
47. Evaluation of the microstructure and mechanical properties of WC particle reinforced aluminium matrix composites fabricated by friction stir processing10.1016/j.matchar.2018.01.053 ↗
48. Casting of SiC reinforced metal matrix composites10.1016/S0924-0136(96)02647-7 ↗
49. High temperature creep behavior of nanometric Si3N4 particulate reinforced aluminium composite10.1016/S0921-5093(96)10870-4 ↗
50. Aluminium matrix tungsten aluminide and tungsten reinforced composites by solid-state diffusion mechanism10.1038/s41598-017-12302-w ↗
51. Wear behaviour of eutectic and hypereutectic Al-Si-Cu-Mg casting alloys tested against a composite brake pad10.1016/S0921-5093(03)00633-6 ↗
52. The microstructure and wear behaviour of garnet particle reinforced Al matrix composites10.1016/j.jmrt.2019.09.012 ↗
53. Effects of the artificial-aging temperature and time on the mechanical properties and spring back behavior of AA6061
54. The effects of mischmetal, cooling rate and heat treatment on the eutectic Si particle characteristics of A319.1, A356.210.1016/j.msea.2007.07.039 ↗
55. Effect of particle size on dry sliding wear behaviour of sillimanite reinforced aluminium matrix composites10.1016/j.ceramint.2017.09.132 ↗
56. Dry sliding wear behaviour of AA6082-T6/SiC/B4C hybrid metal matrix composites using response surface methodology10.1177/1464420716657114 ↗
57. Experimental investigation and optimization on surface parameters of ZrO2 nanoparticles reinforced Al-7050 metal matrix composites for aeronautical applications10.1016/j.matpr.2020.08.265 ↗
58. Experimental investigation on mechanical and wear behaviour of aluminium LM6 /ZrO2 composites fabricated by stir casting method
59. ASTM International 2023 Standard Test Method for Wear Testing with a Pin-on-Disk Apparatus ASTM G99-23