journal article·2017-03

Deformation behavior of high yield strength – High ductility ultrafine-grained 316LN austenitic stainless steel

D.M. Xu, G.Q. Li, X.L. Wan, R.L. Xiong, G. Xu, K.M. Wu, M.C. Somani, R.D.K. Misra

Publisher page

Abstract

Abstract The concept of phase reversion annealing involving extensive cold deformation of metastable austenite to strain-induced martensite, followed by annealing at slightly elevated temperature, developed by Misra’s group in recent years [2] , [3] , [4] , [5] was used to obtain ultrafine-grained structure in a 316LN austenitic stainless steel. The primary objective of this study is to elucidate the deformation mechanisms. The study suggested that an average austenite grain size in the ultrafine regime of ~2.0 μm can be obtained using the experimental conditions described in the study, which is ~6 times finer than the grain size of commercial 316LN steel. The grain refinement led to high yield strength in ultrafine-grained 316LN steel without any significant compromise in ductility. The high plasticity of ultrafine-grained 316LN steel is attributed to the presence of mechanical twins.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Microstructure and Mechanical Properties of Steels · Microstructure and mechanical properties · Metal Alloys Wear and Properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (26)

Show source-provided references
1. Some strengthening methods for austenitic stainless steels10.1002/srin.200806146 ↗
2. On the significance of nature of strain-induced martensite on phase-reversion- induced nanograined/ultrafine-grained austenitic stainless steel10.1007/s11661-009-0072-2 ↗
3. Interplay between grain structure, deformation mechanisms and austenite stability in phase-reversion-induced nanograined/ultrafine-grained austenitic ferrous alloy10.1016/j.actamat.2014.10.038 ↗
4. Strain hardening behavior of phase reversion-induced nanograined/ultrafine-grained (NG/UFG) austenitic stainless steel and relationship with grain size and deformation mechanism10.1016/j.msea.2014.06.065 ↗
5. Challa · Scr. Mater. · 2014 · 86 · 6010.1016/j.scriptamat.2014.05.010 ↗
6. The influence of grain size on the strain-induced martensite formation in tensile straining of anaustenitic 15Cr-9Mn-Ni-Cu stainless steel10.1016/j.msea.2013.04.107 ↗
7. Effect of annealing temperature on nano/ultrafine grain of Ni-free austenitic stainless steel10.1016/j.msea.2013.10.087 ↗
8. Optimizing strength and ductility of austenitic stainless steels through equal-channel angular pressing and adding nitrogen element10.1016/j.msea.2013.08.056 ↗
9. Tensile properties of a nanocrystalline 316L austenitic stainless steel10.1016/j.scriptamat.2005.01.023 ↗
10. Effect of strain-induced martensite on the formation of nanocrystalline 316L stainless steel after cold rolling and annealing10.1016/j.msea.2009.04.038 ↗
11. On the Hall-Petch relationship and substructural evolution in type 316L stainless steel10.1016/0956-7151(95)00110-H ↗
12. The formation mechanism of austenite structure with micro/sub-micrometer bimodal grain size distribution
13. Cold rolled texture and microstructure in types 304 and 316L austenitic stainless steels10.2355/isijinternational.43.1581 ↗
14. The effect of cold rolling regime on microstructure and mechanical properties of AISI 304L stainless steel10.1016/j.jmatprotec.2010.02.010 ↗
15. Tensile properties and twinning behavior of high manganese austenitic steel with fine-grained structure10.1016/j.scriptamat.2008.06.050 ↗
16. Correlations between the calculated stacking fault energy and the plasticity mechanisms in Fe-Mn-C alloys10.1016/j.msea.2004.01.059 ↗
17. Correlation between stacking fault energy and deformation microstructure in high-interstitial-alloyed austenitic steels10.1016/j.actamat.2010.01.056 ↗
18. On the effect of carbon on the stacking fault energy of austenitic stainless steels10.1007/BF02649799 ↗
19. Formation of shear bands and strain-induced martensite during plastic deformation of metastable austenitic stainless steels10.1016/j.actamat.2007.07.015 ↗
20. Variation of stacking fault energy with austenite grain size and its effect on the MS temperature of γ→ε martensitic transformation in Fe-Mn alloy10.1016/S0921-5093(98)00994-0 ↗
21. Crystallographic orientation dependence of ε-martensite transformation during tensile deformation of polycrystalline 30% Mn steel10.1016/j.msea.2013.03.071 ↗
22. The effect of grain size and grain orientation on deformation twinning in a Fe-22 wt.% Mn-0.6 wt.% C TWIP steel10.1016/j.msea.2010.02.041 ↗
23. Dependence of deformation twinning on grain orientation in a high manganese steel10.1016/j.scriptamat.2006.06.004 ↗
24. Effect of grain refinement on thermal stability of metastable austenitic steel10.2320/matertrans.45.2245 ↗
25. Effect of grain size on strain-induced martensitic transformation start temperature in an ultrafine grained metastable austenitic steel10.1007/s12540-011-0804-x ↗
26. Composition and grain size dependencies of strain-induced martensitic transformation in metastable austenitic stainless steels10.2355/tetsutohagane1955.63.5_772 ↗