High strength Mg-9Al serial alloy processed by slow extrusion
Source abstract
Abstract
Abstract The AZ91-0.5Ca alloy was extruded at 250 °C with slow extrusion speed (0.03, 0.3, 3 mm/s) in the current study. The results showed that both the volume fraction and average grain size of DRXed grains increased with the increase of extrusion speed. Furthermore, numerous fine Mg17Al12 phase were observed in the DRXed regions of the extruded alloys, the amount of which decreased by increasing extrusion speed. The decrease of extrusion speed led to the improvement of yield strength and ultimate tensile strength, however, at the expense of elongation. As the extrusion speed decreased to 0.03 mm/s, the yield strength, ultimate tensile strength and elongation of present alloy were ~347.8 MPa, ~402.2 MPa and ~9.1%, respectively, which were superior to the present commercial Mg-Al serial alloys. Detailed reasons are given and analyzed.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Magnesium Alloys: Properties and Applications · Aluminum Alloys Composites Properties · Aluminum Alloy Microstructure Properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (33)
Show source-provided references
1. An effective approach called the composite extrusion to improve the mechanical properties of AZ31 magnesium alloy sheets10.1016/j.msea.2015.12.098 ↗
2. The influence of calcium and cerium mischmetal on the microstructural evolution of Mg–3Al–1Zn during extrusion and resulting mechanical properties10.1016/j.actamat.2008.02.010 ↗
3. Competition behavior of the strengthening effects in as-extruded AZ91 matrix: influence of pre-existed Mg17Al12 phase10.1016/j.msea.2016.01.023 ↗
4. Study on the assemblage of Y and Gd on microstructure and mechanical properties of hot extruded Mg–Al–Zn alloy10.1016/j.msea.2015.05.008 ↗
5. Microstructures and mechanical properties of AZ91D alloys with Y addition10.1016/j.msea.2009.03.030 ↗
6. Effect of Ca additions on the microstructure, thermal stability and mechanical properties of a cast AM60 magnesium alloy10.1016/j.msea.2009.11.043 ↗
7. Improvement of formability of Mg–Al–Zn alloy sheet at low temperatures using differential speed rolling10.1016/j.jallcom.2008.02.029 ↗
8. Microstructures and mechanical properties of AZ91 magnesium alloy processed by multidirectional forging under decreasing temperature conditions10.1016/j.jallcom.2014.08.148 ↗
9. Tensile anisotropy of AZ91 magnesium alloy by equal channel angular processing10.1016/j.jallcom.2014.11.046 ↗
10. Achieving high strength in commercial Mg cast alloys through large strain rolling10.1016/j.matlet.2005.04.061 ↗
11. Significantly improved strength and ductility in bimodal-size grained microstructural magnesium matrix composites reinforced by bimodal sized SiCp over traditional magnesium matrix composites10.1016/j.compscitech.2015.08.009 ↗
12. Influence of deformation rate on microstructure, texture and mechanical properties of indirect-extruded Mg–Zn–Ca alloy10.1016/j.matchar.2014.09.020 ↗
13. High-speed extrusion of dilute Mg-Zn-Ca-Mn alloys and its effect on microstructure, texture and mechanical properties10.1016/j.msea.2016.10.007 ↗
14. Effect of ultra-slow extrusion speed on the microstructure and mechanical properties of Mg-4Zn-0.5Ca alloy10.1016/j.msea.2016.09.059 ↗
15. High-speed indirect extrusion of Mg–Sn–Al–Zn alloy and its influence on microstructure and mechanical properties10.1016/j.jallcom.2016.01.163 ↗
16. Effect of strain-induced precipitation on dynamic recrystallization in Mg–Al–Sn alloys10.1016/j.msea.2014.08.032 ↗
17. Intermetallics in magnesium alloys10.1002/adem.200500202 ↗
18. Strain-induced dynamic precipitation of Mg17Al12 phases in Mg–8Al alloys sheets rolled at 748K10.1016/j.msea.2015.03.112 ↗
19. High-strength extruded Mg–Al–Ca–Mn alloy10.1016/j.scriptamat.2011.04.026 ↗
20. Effect of pre-aging treatment on microstructure and mechanical properties of hot compressed Mg–9Al–1Zn alloy10.1016/j.msea.2009.04.029 ↗
21. Refined microstructure and improved mechanical properties of high-ratio extruded AZ91-xSn magnesium alloy10.1016/j.matchemphys.2015.06.052 ↗
22. Effects of calcium, samarium addition on microstructure and mechanical properties of AZ61 magnesium alloy10.1016/S1002-0721(14)60387-2 ↗
23. Microstructure and mechanical properties of AZ61 alloys with large cross-sectional size fabricated by multi-pass ECAP10.1016/j.msea.2012.09.092 ↗
24. Improved mechanical properties of Mg–7.6Al–0.4Zn alloy through aging prior to extrusion10.1016/j.scriptamat.2014.08.017 ↗
25. Microstructure and mechanical properties of Mg–Al–Sn extruded alloys10.1016/j.jallcom.2015.10.146 ↗
26. Improving tensile properties of dilute Mg-0.27Al-0.13Ca-0.21Mn (at%) alloy by low temperature high speed extrusion10.1016/j.jallcom.2015.07.051 ↗
27. Microstructure and mechanical properties of as-extruded and as-aged Mg–Zn–Al–Sn alloys10.1016/j.msea.2016.01.002 ↗
28. Microstructures and mechanical properties of as-extruded Mg–5Sn–1Zn–xAl (x=1, 3 and 5) alloys10.1016/j.pnsc.2015.08.007 ↗
29. Microstructure and mechanical properties of SiCp/Mg–Al–Zn composites containing Mg17Al12 phases processed by low-speed extrusion10.1016/j.msea.2014.05.062 ↗
30. Microstructure and strengthening mechanism of bimodal size particle reinforced magnesium matrix composite10.1016/j.compositesa.2012.03.007 ↗
31. Influence of the Al2Ca phase on microstructure and mechanical properties of Mg–Al–Ca alloys10.1016/j.jallcom.2015.06.060 ↗
32. Mechanical behavior and strengthening mechanisms in ultrafine grain precipitation-strengthened aluminum alloy10.1016/j.actamat.2013.09.042 ↗
33. Development of dilute Mg–Zn–Ca–Mn alloy with high performance via extrusion10.1016/j.jallcom.2016.01.195 ↗