journal article·2014-06

Effects of strain rate on dynamic mechanical behavior and microstructure evolution of 5A02-O aluminum alloy

Huijuan Ma, Liang Huang, Yi Tian, Jianjun Li

Publisher page

Abstract

Abstract This paper studies the effects of strain rate on dynamic mechanical behavior and microstructure evolution of 5A02-O aluminum alloy at room temperature. Based on the results of the dynamic tensile tests and compressive tests at strain rates of 1000–5000 s −1 by split Hopkinson bar as well as the results of quasi-static tests at strain rate of 0.001 s −1 , it is shown that with increasing strain rate, the flow stress and tensile strength significantly increase and notable strain hardening and thermal softening behaviors are observed for 5A02-O with elongation of 63.00% and softening ratio of 73.23% at the strain rate of 4000 s −1 . The strain rate sensitivity for 5A02-O is enhanced in the range of 1000–3000 s −1 . Scanning electron microscopy (SEM) observations illustrate that the fracture surfaces are characterized by larger and deeper dimple-like structure with more precipitates at higher strain rates, which indicates the ductile failure mode. The enhancement of ductility is interpreted via the inertia effect which may contribute to diffuse necking, slow down the necking development and delay the onset of fracture. Furthermore, transmission electron microscopy (TEM) observations show that higher strain rate leads to higher dislocation density, smaller cell size with thinner cell wall and the appearance of dislocation wall with parallel dislocation lines. Dislocation cells are incomplete under dynamic deformation. In addition, the micro-hardness of 5A02-O increases with increasing strain rate.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: High-Velocity Impact and Material Behavior · Microstructure and mechanical properties · Aluminum Alloys Composites Properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (37)

Show source-provided references
1. Miller · Mater. Sci. Eng. A · 2000 · 280 · 3710.1016/S0921-5093(99)00653-X ↗
2. Heinz · Mater. Sci. Eng. A · 2000 · 280 · 10210.1016/S0921-5093(99)00674-7 ↗
3. Li · 2004
4. G. Zittel, Proceedings of the 4th International Conference on High Speed Forming, Columbus, Ohio, USA, 2010, pp. 2–15.
5. Zhang · Mater. Des. · 2011 · 32 · 446110.1016/j.matdes.2011.03.058 ↗
6. Etter · Mater. Sci. Eng. A · 2007 · 445–446 · 9410.1016/j.msea.2006.09.036 ↗
7. James · Int. J. Fatigue · 2009 · 31 · 2810.1016/j.ijfatigue.2008.04.010 ↗
8. Ezuber · Mater. Des. · 2008 · 29 · 80110.1016/j.matdes.2007.01.021 ↗
9. Halambek · Mater. Chem. Phys. · 2013 · 137 · 78810.1016/j.matchemphys.2012.09.066 ↗
10. Lee · Mater. Sci. Eng. A · 2007 · 40910.1016/j.msea.2007.01.121 ↗
11. Park · Scr. Mater. · 2004 · 51 · 47910.1016/j.scriptamat.2004.06.001 ↗
12. Hojjati · J. Mater. Proc. Tech. · 2008 · 205 · 48210.1016/j.jmatprotec.2007.11.208 ↗
13. Han · Trans. Nonferrous Met. Soc. China · 2012 · 22 · 38210.1016/S1003-6326(12)61735-X ↗
14. Yuan · J. Mater. Proc. Technol. · 2006 · 177 · 68010.1016/j.jmatprotec.2006.04.044 ↗
15. Smerd · Int. J. Impact Eng. · 2005 · 32 · 54110.1016/j.ijimpeng.2005.04.013 ↗
16. Tucker · Mech. Mater. · 2010 · 42 · 89510.1016/j.mechmat.2010.07.003 ↗
17. K. Tanaka, T. Nojima, Proceedings of the 19th Japan Congress on Materials Research, Tokyo, Japan, 1975, pp. 48–51.
18. Chen · Int. J. Solids Struct. · 2009 · 46 · 382510.1016/j.ijsolstr.2009.07.013 ↗
19. Ye · Mater. Sci. Eng. A · 2013 · 582 · 8410.1016/j.msea.2013.06.028 ↗
20. Chen · Int. J. Impact Eng. · 2011 · 38 · 82410.1016/j.ijimpeng.2011.05.002 ↗
21. Hou · Int. J. Solids Struct. · 2012 · 49 · 275410.1016/j.ijsolstr.2012.05.005 ↗
22. Lee · J. Alloys Compd. · 2010 · 493 · 58010.1016/j.jallcom.2009.12.161 ↗
23. Wen · Mater. Sci. Eng. A · 2003 · 354 · 27910.1016/S0921-5093(03)00017-0 ↗
24. Khan · Int. J. Plast. · 2004 · 20 · 223310.1016/j.ijplas.2003.06.005 ↗
25. Yan · Mater. Sci. Eng. A · 2014 · 598 · 19710.1016/j.msea.2013.12.001 ↗
26. Wei · Acta Mater. · 2008 · 56 · 174110.1016/j.actamat.2007.12.028 ↗
27. Khakbaz · Mater. Sci. Eng. A · 2012 · 532 · 2610.1016/j.msea.2011.10.057 ↗
28. Khan · Int. J. Plast. · 2012 · 36 · 110.1016/j.ijplas.2012.02.001 ↗
29. Hu · Acta Mater. · 1996 · 44 · 102110.1016/1359-6454(95)00228-6 ↗
30. Liu · Mater. Sci. Eng. A · 2012 · 551 · 28010.1016/j.msea.2012.05.018 ↗
31. Balanethiram · Scr. Metall. Mater. · 1994 · 30 · 51510.1016/0956-716X(94)90613-0 ↗
32. Balanethiram · J. Mater. Process. Technol. · 1994 · 45 · 59510.1016/0924-0136(94)90404-9 ↗
33. Holt · J. Appl. Phys. · 1970 · 41 · 319710.1063/1.1659399 ↗
34. D.L. Holt, Proceedings of the Second International Conference on the Strength of Metals and Alloys, American Society for Metals, California, 1970, pp. 477–481.
35. Koneva · Mater. Sci. Eng. A · 2008 · 483–484 · 17910.1016/j.msea.2006.08.140 ↗
36. Lee · Scr. Mater. · 2006 · 54 · 146310.1016/j.scriptamat.2005.12.054 ↗
37. Meyers · 1994