Microstructure and mechanical properties of aluminium alloy 7A52 thick plates welded by robotic double-sided coaxial GTAW process
Source abstract
Abstract
Abstract The high strength aluminium alloy 7A52 thick plate is commonly welded by double-V butt welding. The general one sided arc welding requires indispensable root cleaning before the rear side root weld, which consumes excessive time and cost. Thus the robotic welding is always difficult to be carried on. In this paper, a novel robotic double-sided coaxial GTAW process has been applied to the welding of Al7A52. The microstructure and mechanical properties of the thick weld joints both welded by robotic self-fluxing double sided coaxial GTAW (RSF-DSC-GTAW) and robotic wire-feed double sided coaxial GTAW (RWF-DSC-GTAW) has been investigated. It was found that the microstructures of weld zones of both processes typically consist of α (Al) and β (MgZn 2 ) phases. Moreover, the weld zone of the RWF-DSC-GTAW joint exhibits Interval layers distribution because of the less proportion of β phase. The average micro hardness in the weld zone of RSF-DSC-GTAW joints and RWF-DSC-GTAW joints are 91.9 HV and 80.1 HV, respectively. With a better elongation property, the average ultimate tensile strength of RSF-DSC-GTAW joint is 344 Mpa. While it is 244 Mpa for the RWF-DSC-GTAW joint. It is considered that the mechanical properties of the RSF-DSC-GTAW joint are more superior to the RWF-DS-GTAW joint.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Advanced Welding Techniques Analysis · Aluminum Alloys Composites Properties · Welding Techniques and Residual Stresses
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (20)
Show source-provided references
1. Microstructure and mechanical properties of 7A52 aluminum alloys double-wire welding joints. Chines
2. Study on welding process and prosperities of AA5754 Al-alloy welded by double pulsed gas metal arc welding10.1016/j.matdes.2013.02.087 ↗
3. The procedure handbook of arc welding, (twelfth ed.), The Lincoln electric company, 1973.
4. Fatigue behavior of FSW and MIG weldment for two aluminum alloys10.1016/j.tafmec.2007.06.001 ↗
5. Effect of post weld heat treatments on microstructure and mechanical properties of friction stir welded joints of Al–Zn–Mg alloy AA703910.1016/j.matdes.2012.06.018 ↗
6. Influence of pre-weld temper conditions of base metal on microstructure and mechanical properties of friction stir weld joints of Al–Zn–Mg alloy AA703910.1016/j.msea.2014.09.094 ↗
7. The effects of shorts pulse laser surface cleaning on porosity formation a reduction in laser welding of aluminum for automotive component manufacture10.1016/j.optlastec.2014.05.010 ↗
8. A comparative study of laser-arc double-sided welding and double-sided arc welding of 6mm 5A06 aluminum alloy10.1016/j.matdes.2010.11.041 ↗
9. Microstructure and mechanical properties of aluminum 5083weldments by gas tungsten arc and gas metal arc welding10.1016/j.msea.2012.03.108 ↗
10. Microstructure and mechanical properties of a thick-section high-strength steel welded joint by novel double-sided hybrid fibre laser-arc welding10.1016/j.msea.2013.05.077 ↗
11. Abnormal macropore formation during double-sided gas tungsten arc welding of magnesium AZ91D alloy10.1016/j.matchar.2007.08.021 ↗
12. Study on nonhomogeneity of low-cycle fatigue properties along thickness direction of plate for friction stir welded aluminium alloy joint
13. Microstructure and properties of welding joints of 30mm thickness 7A52 aluminium alloy plate by friction stir welding
14. Friction stir welding on thick plate of 7A52 aluminium alloy
15. Sensing and control of double side arc welding process10.1115/1.1467603 ↗
16. Welding aluminum alloy 6061 with the opposing dual-torch GTAW process
17. Double sided arc welding of AA5182 aluminum alloy sheet10.1179/174329308X271715 ↗
18. Current density distribution in double-sided GTAW process
19. Double-sided laser beam welded T-joints for aluminum aircraft fuselage panels: process, microstructure, and mechanical properties10.1016/j.matdes.2011.07.059 ↗
20. Huajun Zhang, Double-sided arc welding of large thick plate of high strength steel and robot automatic welding technology (Ph.D. thesis), Haerbin Institute of Technology, In Chinese, 2009.