journal article·2019-09

The effect of soaking time after ultrafast heating on the microstructure and mechanical behavior of a low carbon steel

M.A. Valdes-Tabernero, R.H. Petrov, M.A. Monclus, J.M. Molina-Aldareguia, I. Sabirov

Publisher page

Abstract

Abstract The main objective of this study is to understand the effect of the soaking time during the ultrafast heat treatment of a low carbon steel on its complex multi-phase microstructure, tensile mechanical behavior and properties of individual microconstituents. Tensile tests were performed to determine the macro-mechanical properties. Nanoindentation testing was carried out on individual microconstituents (martensite, recrystallized ferrite and non-recrystallized ferrite) identified a priori via EBSD analysis to measure their properties. It is shown that ultrafast heating combined with short soaking times results in improved macro-mechanical properties due to finer grain size and higher fraction of non-recrystallized ferrite, that has a higher nanohardness than recrystallized ferrite. Prolonged soaking times eliminate the advantages of the ultrafast heat treatment. This occurs because, even though a long soaking time promotes a higher volume fraction of martensite than a short one, it also induces substantial grain growth and complete recrystallization of the ferritic matrix. On the micro-scale, the ferritic grains show two different types of mechanical response. The recrystallized ferritic grains are prone to show pop-in events on the nanoindentation curves that are associated to dislocation nucleation events as a consequence of their low dislocation density, while non-recrystallized ferritic grains demonstrate a continuous response. The relationship between microstructure and mechanical properties on the macro- and micro-scales is discussed with respect to the microstructure, which in turn strongly depends on the applied heating rate and soaking time. A general recipe for microstructural design to improve the tensile mechanical behavior of low carbon steels implementing controlled heating and soaking conditions is outlined.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Microstructure and Mechanical Properties of Steels · Metal and Thin Film Mechanics · Hydrogen embrittlement and corrosion behaviors in metals

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (46)

Show source-provided references
1. Advanced high strength steels for automotive industry10.3989/revmetalm.1158 ↗
2. T.E. steel Organization
3. Development of rapid heating and cooling (flash processing) process to produce advanced high strength steel microstructures10.1179/174328409X433813 ↗
4. Texture formation in high strength low alloy steel reheated with ultrafast heating rates
5. Austenite formation in 0.2% C and 0.45% C steels under conventional and ultrafast heating10.1016/j.matdes.2016.12.009 ↗
6. http://www.flashbainite.com/, (n.d.).
7. The effect of the pre-heating stage on the microstructure and texture of a cold rolled FeCMnAlSi steel under conventional and ultrafast heating10.1016/j.matchar.2017.06.010 ↗
8. The effect of ultrafast heating in cold-rolled low carbon Steel : recrystallization and texture evolution10.3390/met6110288 ↗
9. The effect of heating rate on the recrystallization behavior in cold rolled ultra low carbon steel
10. The influence of ultra-fast annealing prior to quenching and partitioning on the microstructure and mechanical properties10.1016/j.msea.2014.12.118 ↗
11. Recrystallization kinetics of low and ultra low carbon steels during high-rate annealing10.2355/isijinternational.41.1053 ↗
12. Influence of heating rate on anisothermal recrystallization in low and ultra-low carbon steels10.1016/S0921-5093(00)01882-7 ↗
13. The effect of heating rate and soaking time on microstructure of an advanced high strength steel10.1016/j.matchar.2019.109822 ↗
14. Effect of ultrafast heating on the properties of the microconstituents in a low-carbon steel10.1007/s11661-018-4658-4 ↗
15. Vercruysse · 2016
16. Ultra-rapid intercritical annealing to improve deep drawability of low-carbon, al-killed steels10.1007/s11661-012-1096-6 ↗
17. Microstructure and mechanical properties of low carbon Al-killed steels after ultra-rapid annealing cycles10.4028/www.scientific.net/MSF.638-642.3368 ↗
18. Puype · 2014
19. Microstructure, texture and mechanical properties in a low carbon steel after ultrafast heating10.1016/j.msea.2016.06.056 ↗
20. High-efficiency fast-heating annealing of a cold-rolled dual-phase steel10.1016/j.matdes.2014.01.055 ↗
21. Fonstein · 2015
22. A different type of indentation size effect10.1016/j.scriptamat.2008.07.026 ↗
23. Castro Cerda · 2017
24. Petrov · 2015 · 46
25. An electron backscattered diffraction study on the dynamic recrystallization behavior of a nickel – chromium alloy (800H) during hot deformation10.1016/j.msea.2013.07.037 ↗
26. Analysis of local orientation gradients in deformed single crystals10.1016/j.ultramic.2004.11.016 ↗
27. An improved technique for determining hardness and elastic modulus using load and displacement sensing indentation experiments10.1557/JMR.1992.1564 ↗
28. A new view of the onset of plasticity during the nanoindentation of aluminium10.1038/nmat1714 ↗
29. Nanoindentation-induced deformation behavior in the vicinity of single grain boundary of interstitial-free steel10.2320/matertrans.46.2026 ↗
30. Nanoindentation creep of single- crystal tungsten and gallium arsenide10.1080/01418619708214217 ↗
31. Relationship between yield point phenomena and the nanoindentation pop-in behavior of steel10.1557/jmr.2011.208 ↗
32. Grain refinement of a cold rolled TRIP assisted steel after ultra short annealing10.4028/www.scientific.net/MSF.715-716.661 ↗
33. Martensite in steel : strength and structure10.1016/S0921-5093(99)00288-9 ↗
34. Effect of martensite strength on the tensile strength of dual phase steels10.1007/BF02385411 ↗
35. Deformation behavior of a high strength multiphase steel at macro- and micro-scales10.1016/j.msea.2014.05.068 ↗
36. Dieter · 1988
37. Effect of microstructure on retained austenite stability and work hardening of TRIP steels10.1016/j.msea.2011.02.032 ↗
38. Effect of microstructure on the stability of retained austenite in transformation-induced-plasticity steels10.1007/s11661-006-0213-9 ↗
39. A theoretical model for the flow behavior of commercial dual-phase steels containing metastable retained Austenite : Part I . Derivation of flow curve equations10.1007/BF02662402 ↗
40. H.K.D.H. Bhadeshia, R.W.K. Honeycombe, Steels: Microstructure and Properties, third ed., Elsevier Ltd, Oxford, n.d.
41. Microstructures and hardness of as-quenched martensites (0.1–0.5%C)10.1016/j.actamat.2011.05.061 ↗
42. On the measurement of the nanohardness of the constitutive phases of TRIP-assisted multiphase steels10.1016/S0921-5093(01)01689-6 ↗
43. Thermal and mechanical stability of retained austenite surrounded by martensite with di ff erent degrees of tempering10.1016/j.msea.2017.03.017 ↗
44. Orientation gradients and geometrically necessary dislocations in ultrafine grained dual-phase steels studied by 2D and 3D EBSD10.1016/j.msea.2010.01.004 ↗
45. Geometrically necessary boundaries , incidental dislocation boundaries and geometrically necessary dislocations10.1016/S1359-6462(02)00358-5 ↗
46. Clyne · 1993