journal article·2021-10

Deformation behavior of 42CrMo4 over a wide range of temperatures and strain rates in Split-Hopkinson pressure bar tests

Janis S. Kimm, Jim A. Bergmann, Florian Wöste, Fabian Pöhl, Petra Wiederkehr, Werner Theisen

Publisher page

Abstract

Abstract In this research, Split-Hopkinson pressure bar tests were performed on samples made from the quenched and tempered steel 42CrMo4 in four different heat-treatment conditions. These samples were subjected to four different pressures and five different temperatures while deforming the samples at strain rates in the range of 103 s−1. Stress-strain curves and the strain rate were computed from the measured signals. The polished cross-sections of the samples were analyzed before and after testing by means of SEM, EBSD, nanoindentation, and microhardness testing. A variety of deformation characteristics were identified and correlated with the pre-test and post-test microstructure. This work focusses on the influence of the microstructure on deformation and provides a detailed understanding on the deformation of the 42CrMo4 steel over a wide range of parameter values.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Metal and Thin Film Mechanics · High-Velocity Impact and Material Behavior · Advanced materials and composites

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (53)

Show source-provided references
1. An investigation of the mechanical properties of materials at very high rates of loading10.1088/0370-1301/62/11/302 ↗
2. The use of the split Hopkinson pressure bar techniques in high strain rate materials testing10.1243/0954406971522042 ↗
3. Advances in material and friction data for modelling of metal machining10.1016/j.cirp.2017.05.002 ↗
4. Recent advances in modelling of metal machining processes10.1016/j.cirp.2013.05.006 ↗
5. Data processing in the split Hopkinson pressure bar tests10.1016/0734-743X(94)90011-9 ↗
6. W.J. Kang, S.S. Cho, H. Huh, D.T. Chung, Identification of Dynamic Behavior of Sheet Metals for an Auto-Body with Tension Split Hopkinson Bar, SAE Technical Paper 981010. https://doi.org/10.4271/981010.10.4271/981010 ↗
7. Hopkinson techniques for dynamic recovery experiments10.1098/rspa.1991.0150 ↗
8. Hopkinson bar experimental technique: a critical review10.1115/1.1704626 ↗
9. Round-Robin test of split Hopkinson pressure bar10.1016/j.ijimpeng.2018.12.003 ↗
10. Response of split Hopkinson bar apparatus signal to end-surface damage, numerical and experimental studies10.1051/epjconf/20122604037 ↗
11. Increased accuracy of SHPB test apparatus to better evaluate naval steels10.1016/j.proeng.2011.04.375 ↗
12. Wave propagation in the split hopkinson pressure bar10.1115/1.3225620 ↗
13. Smoothing and differentiation of data by simplified least squares procedures10.1021/ac60214a047 ↗
14. An improved technique for determining hardness and elastic modulus using load and displacement sensing indentation experiments10.1557/JMR.1992.1564 ↗
15. The effects of microstructure, strain rates and geometry on dynamic impact response of a carbon–manganese steel10.1016/j.msea.2011.10.096 ↗
16. High strength Fe–Mn–(Al, Si) TRIP/TWIP steels development — properties — application10.1016/S0749-6419(00)00015-2 ↗
17. Effect of high strain rate on plastic deformation of a low alloy steel subjected to ballistic impact10.1016/j.jmatprotec.2005.02.157 ↗
18. Deformation and fracture behavior of alumina particle-reinforced Al 6061-T6 composite during dynamic mechanical loading10.1007/s11661-007-9242-2 ↗
19. Mechanical behavior and high-resolution EBSD investigation of the microstructural evolution in AISI 321 stainless steel under dynamic loading condition10.1016/j.msea.2016.07.095 ↗
20. High strain-rate fracture and failure of a high strength low alloy steel in compression10.1016/j.msea.2009.07.026 ↗
21. Deformation and failure mechanism in AISI 4340 steel under ballistic impact10.1016/j.tafmec.2005.11.005 ↗
22. An investigation on the adiabatic shear bands in depleted U-0.75 wt % Ti alloy under dynamic loading10.3390/met8020145 ↗
23. Effect of microstructure on the nucleation and initiation of adiabatic shear bands (ASBs) during impact10.1016/j.msea.2014.07.095 ↗
24. Dynamic shear band propagation and failure in AISI 4340 steel10.1016/j.jmatprotec.2005.03.016 ↗
25. Characterisation of fine-scale microstructures by electron backscatter diffraction (EBSD)10.1016/j.scriptamat.2004.05.016 ↗
26. Study of the formation of adiabatic shear bands in steels10.1016/S0924-0136(01)00952-9 ↗
27. Shear strain localisation and fracture in high strength structural materials
28. Effect of prior heat treatment on the dynamic impact behavior of 4340 steel and formation of adiabatic shear bands10.1016/j.msea.2011.08.036 ↗
29. Effect of heat treatment on stability of impact-induced adiabatic shear bands in 4340 steel10.1016/j.msea.2012.03.057 ↗
30. Finite element modeling of the formation of adiabatic shear bands in AISI 4340 steel10.1016/S0921-5093(99)00026-X ↗
31. Effect of heat treatment on adiabatic shear bands in a high-strength low alloy steel10.1016/j.msea.2005.11.059 ↗
32. Adiabatic shear banding in AISI 1045 steel during high speed machining: mechanisms of microstructural evolution10.1016/j.msea.2011.10.071 ↗
33. Recrystallisation - some applied aspects10.1016/S0079-6425(97)00026-1 ↗
34. TEM study on the surface white layer in two turned hardened steels10.1016/S0921-5093(01)01447-2 ↗
35. The nature of the white-etching surface layers produced during reaming ultra-high strength steel10.1016/0025-5416(75)90010-5 ↗
36. White layers and thermal modeling of hard turned surfaces10.1016/S0890-6955(99)00036-X ↗
37. Cutting mechanism during machining of hardened steel10.1179/mst.1987.3.4.299 ↗
38. Tempering of steel
39. Effect of metallurgical parameters on shear band formation in low-carbon (~0.20 Wt Pct) steels10.1007/BF02647311 ↗
40. Splat quenching of iron-nickel-boron alloys
41. Non-isothermal phase-transformation kinetics model for evaluating the austenization of 55CrMo steel based on Johnson–Mehl–Avrami equation10.1016/j.matdes.2015.12.110 ↗
42. Shear band formation in 4340 steel: a TEM study10.1016/0167-6636(94)90052-3 ↗
43. Adiabatic shear band formation during dynamic torsional deformation of an HY-100 steel10.1016/0956-7151(93)90026-O ↗
44. Recrystallization kinetics within adiabatic shear bands10.1016/S1359-6454(96)00193-0 ↗
45. Large strain work hardening and textures10.1016/0079-6425(80)90001-8 ↗
46. Dodd · 2014
47. An experimental study of the formation process of adiabatic shear bands in a structural steel10.1016/0022-5096(88)90012-9 ↗
48. Hull · 2011
49. Self-organization of shear bands in titanium and Ti–6Al–4V alloy10.1016/S1359-6454(01)00356-1 ↗
50. Self organization of shear bands in stainless steel10.1016/j.msea.2004.05.069 ↗
51. Dynamic shear band formation in Aluminum 6061-T6 and Aluminum 6061-T6/Al2O3 composites10.1016/j.msea.2006.12.034 ↗
52. Initiation of adiabatic shear failure in a clamped circular plate struck by a blunt projectile10.1016/j.ijimpeng.2004.04.011 ↗
53. The tempering of iron- carbon martensite; dilatometric and calorimetric analysis10.1007/BF02645469 ↗