Laser additive manufacturing of novel Al-matrix composites reinforced with high-volume multiscale in-situ Al4C3
Source abstract
Abstract
In this work, novel Al-matrix composites (AMCs) reinforced with a high-volume fraction of multiscale in-situ Al 4 C 3 were successfully fabricated via laser powder bed fusion (L-PBF) using Al-12Si/carbon fibers (CFs) mixed powders. Owing to the steep thermal gradients and rapid solidification inherent to the L-PBF process, two distinct types of in-situ Al 4 C 3 reinforcements were formed: reaction-formed high-aspect-ratio (HAR, ∼60) Al 4 C 3 rods and precipitation-formed medium-aspect-ratio (MAR, ∼15) Al 4 C 3 nanorods. As a result, the in-situ composite prepared from Al-12Si/10%CFs powder mixture achieved a tensile strength of 66.8 MPa at 673 K, approximately three times higher than that of the unreinforced alloy (22.1 MPa). This improvement is primarily attributed to load transfer strengthening provided by the HAR-Al 4 C 3 rods, and Orowan strengthening induced by the MAR-Al 4 C 3 nanorods. These findings provide new insights into the design and laser additive manufacturing of next-generation in-situ AMCs.
Source: openalex_inverted_index · Quality: baseline
Research context
OpenAlex topics: Additive Manufacturing Materials and Processes · Aluminum Alloys Composites Properties · High Entropy Alloys Studies
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (62)
Show source-provided references
1. Heat-resistant super-dispersed oxide strengthened aluminum alloys10.1038/s41563-024-01884-2 ↗
2. Aluminum with dispersed nanoparticles by laser additive manufacturing10.1038/s41467-019-12047-2 ↗
3. Design of high-performance sustainable aluminum alloy series for laser additive manufacturing10.1038/s41467-025-67281-8 ↗
4. High-temperature mechanical properties and fracture mechanisms of Al-Si piston alloy reinforced with in situ TiB2 particles10.1016/j.msea.2015.03.021 ↗
5. Laser powder bed fusion of an ultrafine microstructural in-situ TiB2/Al composite with excellent mechanical properties and thermal stability at elevated temperatures10.1016/j.msea.2023.145969 ↗
6. Elevated temperature mechanical properties of TiCN reinforced AlSi10Mg fabricated by laser powder bed fusion additive manufacturing10.1016/j.msea.2021.141025 ↗
7. Mechanical behavior of particle reinforced metal matrix composites10.1002/1527-2648(200106)3:6<357::AID-ADEM357>3.0.CO;2-I ↗
8. Improved mechanical properties of mechanically milled Mg2Si particles reinforced aluminum-matrix composites prepared by hot extrusion10.1016/j.msea.2023.144904 ↗
9. In-situ synthesis of a novel multiphase reinforced Al-matrix composite prepared from A6061 alloy and a small amount of MXene10.1016/j.vacuum.2025.114133 ↗
10. Size-dependent tribological performance of graphene-reinforced Al matrix composites
11. Additively manufactured lightweight and hard high-entropy alloys by thermally activated solvent extraction. High10.1007/s44210-024-00029-z ↗
12. Recent progress in laser additive manufacturing of aluminum matrix composites10.1016/j.coche.2020.01.005 ↗
13. Data-driven design and fabrication of heat-resistant, ultrastrong, lightweight aluminum-based entropy alloy by additive
14. High-strength of additive-manufactured PEEK and Ti6Al4V structure via warm isostatic pressing: applications in medical implants and injection moulds10.1080/17452759.2024.2449566 ↗
15. Interfacial phenomena in thermally sprayed multiwalled carbon nanotube reinforced aluminum nanocomposite10.1016/j.actamat.2006.09.025 ↗
16. Formation of the orientation relationship-dependent interfacial carbide in Al matrix composite affected by architecture carbon nanotube10.1016/j.actamat.2022.117758 ↗
17. Exploring the size effects of Al4C3 on the mechanical properties and thermal behaviors of Al-based composites reinforced by SiC and carbon nanotubes10.1016/j.carbon.2018.04.048 ↗
18. Solid-state interfacial reaction and load transfer efficiency in carbon nanotubes (CNTs)-reinforced aluminum matrix composites10.1016/j.carbon.2016.12.013 ↗
19. Nucleation and growth mechanisms of interfacial carbide in graphene nanosheet/Al composites10.1016/j.carbon.2020.01.032 ↗
20. Design of high-performance Al4C3/Al matrix composites for electric conductor10.1016/j.msea.2020.140331 ↗
21. In situ formation of uniformly dispersed Al4C3 nanorods during additive manufacturing of graphene oxide/Al mixed powders10.1016/j.carbon.2018.09.057 ↗
22. Microstructure and mechanical property of graphene oxide/AlSi10Mg composites fabricated by laser additive manufacturing10.1016/j.matchar.2020.110678 ↗
23. Simultaneously enhancing strength and ductility of selective laser melted AlSi10Mg via introducing in-cell Al4C3 nanorods10.1080/21663831.2023.2173028 ↗
24. Investigation on the microstructure and mechanical properties of CNTs-AlSi10Mg composites fabricated by selective laser melting10.3390/ma14040838 ↗
25. Selective laser melting of carbon/AlSi10Mg composites: microstructure, mechanical and electronical properties10.1016/j.jallcom.2015.12.126 ↗
26. Effect of aluminum carbide on thermal conductivity of the unidirectional CF/Al composites fabricated by low pressure infiltration process10.1016/j.compscitech.2014.03.022 ↗
27. Carbon fiber reinforced metal matrix composites: fabrication processes and properties10.1016/j.compositesa.2016.10.032 ↗
28. Orientation control of carbon fibers and enhanced thermal/mechanical properties of hot-extruded carbon fibers/aluminum composites10.1016/j.diamond.2021.108432 ↗
29. Microstructure and thermal properties of nickel-coated carbon fibers/aluminum composites10.1177/0021998319899154 ↗
30. Effect of reinforcement volume fraction and T6 heat treatment on microstructure, thermal and mechanical properties of mesophase pitch-based carbon fiber reinforced aluminum matrix composites10.1016/j.msea.2021.142469 ↗
31. Evaluation of reactive wetting kinetics of carbon fibers by molten Al-Ti alloy and its application to the fabrication of Al/carbon fiber composites10.1016/j.jallcom.2023.172168 ↗
32. In-process fabrication of carbon-dispersed aluminum matrix composite using selective laser melting10.3390/met10050619 ↗
33. Joining of aluminum and CFRP via laser powder bed fusion: influence of experimental Set-Up and laser processing on microstructure and mechanical properties10.3390/polym15183839 ↗
34. A review of particulate-reinforced aluminum matrix composites fabricated by selective laser melting10.1016/S1003-6326(20)65357-2 ↗
35. Evading ductility deterioration in aluminum matrix composites via intragranulation of nano-reinforcement by reactive selective laser melting10.1016/j.msea.2022.144552 ↗
36. A selective laser melting and solution treatment refined Al-12Si alloy with a controllable ultrafine eutectic microstructure and 25% tensile ductility10.1016/j.actamat.2015.05.017 ↗
37. Advancements in aluminum matrix composites reinforced with carbides and graphene: a comprehensive review10.1515/ntrev-2023-0111 ↗
38. Crack deflection at an interface between dissimilar elastic materials10.1016/0020-7683(89)90021-8 ↗
39. Preparation, microstructure and properties of Al-Al4C3 system produced by mechanical alloying10.1016/j.matdes.2004.11.012 ↗
40. High-temperature mechanical properties of AlSi10Mg specimens fabricated by additive manufacturing using selective laser melting technologies (AM-SLM)
41. High-temperature mechanical properties and thermal cycling stability of Al-50Si alloy for electronic packaging10.1016/j.msea.2018.05.020 ↗
42. Effect of temperature on the mechanical properties of Al-Si-Cu-Mg-Ni-Ce alloy10.1016/j.msea.2021.141762 ↗
43. Si phase modification on the elevated temperature mechanical properties of Al-Si hypereutectic alloys10.1016/j.msea.2019.01.119 ↗
44. Effect of Nd on microstructure and mechanical properties of cast Al-Si-Cu-Ni-Mg piston alloys10.1016/j.jallcom.2016.10.300 ↗
45. Ti addition-induced simultaneous enhancement of powder properties, melting behavior, and tensile response of pure Al for laser powder bed fusion10.1016/j.msea.2025.148458 ↗
46. High temperature tensile and wear behaviour of aluminum silicon alloy10.1016/j.msea.2010.09.020 ↗
47. Effect of graphite and transition elements (Cu, Ni) on high temperature tensile behaviour of Al-Si alloys10.1016/j.matchemphys.2011.02.069 ↗
48. Microstructure, tensile properties and thermal stability of AlMgSi ScZr alloy printed by laser powder bed fusion10.1016/j.jmst.2020.08.033 ↗
49. Temperature effects on the tensile properties of cast and heat treated aluminum alloy A31910.1016/j.msea.2009.05.022 ↗
50. Review on laser directed energy deposited aluminum alloys10.1088/2631-7990/ad16bb ↗
51. Laser powder bed fusion of AlSi10Mg alloy: numerical investigation on the temperature field evolution10.1016/j.finmec.2022.100109 ↗
52. Creation of heavily La-doped SrTiO3 thermoelectric films achieved by freeze-dry pulsated orifice ejection method and laser powder bed fusion. Smart
53. In-situ formation of ceramic layer on Mo-based composites via laser powder bed fusion10.1016/j.mtla.2020.100655 ↗
54. Critical assessment and thermodynamic modeling of the Al-C system10.1016/j.calphad.2019.101648 ↗
55. The third generation calphad description of Al-C including revisions of pure Al and C10.1016/j.calphad.2021.102250 ↗
56. Third generation of unary calphad descriptions and the avoidance of Re-Stabilized solid phases and unexpected large heat capacity10.1007/s11669-022-00976-3 ↗
57. Dissolution of Al 6%wt C mixture using mechanical alloying10.4028/www.scientific.net/DDF.391.82 ↗
58. Preparation of graphene coated aluminum composite powders by high-energy ball milling
59. Length effect of carbon nanotubes on the strengthening mechanisms in metal matrix composites10.1016/j.actamat.2017.08.048 ↗
60. Tensile properties of fibre-reinforced metals: copper/tungsten and copper/molybdenum10.1016/0022-5096(65)90035-9 ↗
61. Strengthening in carbon nanotube/aluminium (CNT/Al) composites10.1016/j.scriptamat.2005.07.022 ↗
62. Superior high-temperature tensile properties of aluminum matrix composites reinforced with carbon nanotubes10.1016/j.carbon.2022.02.009 ↗