Process optimization research on surface remelting treatment of additive manufactured 316L stainless steel by circular oscillating laser
Source abstract
Abstract
Abstract This study adopted circular oscillating laser remelting (COLR) to postprocess additive manufactured 316L stainless steel surfaces, systematically exploring its influence on surface roughness, subsurface defects, and material properties. Extended depth-of-field microscopy and scanning electron microscopy (SEM) were employed to characterize surface and cross-sectional morphologies, revealing surface-adhered spherical particles and subsurface defects (microcracks, pores, and ablation marks) predominantly distributed at 30–50 μm depth, with maximum crack depth reaching 99.98 μm and ablation particle depth of 46.77 μm. Response surface methodology was used to investigate the effects of key parameters (laser power, scanning speed, and rotation speed) on surface roughness and remelting depth. Results showed that at 120 W, insufficient energy–induced serrated undulations and molten pools of 40–50 μm with columnar grains; at 150 W, 23.41 μm-wide and 1.00 μm-high black micro-protrusions formed, accompanied by pools of 94–136 μm with columnar-equiaxed composite grains; at 180 W, violent pool fluctuations and edge spatters occurred, producing pools of 195–239 μm with 10 μm-thick columnar grains on the outer surface of the central region. Under the optimal parameters of 180 W, 5 mm/s, and 40 % rotation speed, COLR treatment reduced the surface roughness by ∼91% (from 7.3 to 0.65 μm) and increased the average microhardness of the remelted zone from approximately 222 HV (substrate) to 249 HV.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: Additive Manufacturing Materials and Processes · High Entropy Alloys Studies · Laser Material Processing Techniques
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
Affiliations
Department of Marine Equipment, Shanghai Marine Equipment Research Institute , Shanghai , 200031 , China
School of Mechanical Engineering, Jiangsu University , Zhenjiang , Jiangsu, 212013 , China
References (32)
Show source-provided references
1. DebRoy, T., Wei, H.L., Zuback, J.S., Mukherjee, T., Elmer, J.W., Milewski, J.O., et al., Additive manufacturing of metallic components–process, structure and properties. Prog. Mater. Sci., 2018; 92: 112–224. 10.1016/j.pmatsci.2017.10.00110.1016/j.pmatsci.2017.10.001 ↗
2. Lodhi, M.J.K., Iams, A.D., Sikora, E., Palmer, T.A., Microstructural features contributing to macroscopic corrosion: The role of oxide inclusions on the corrosion properties of additively manufactured 316L stainless steel. Corros. Sci., 2022; 203: 110354. 10.1016/j.corsci.2022.11035410.1016/j.corsci.2022.110354 ↗
3. Liu, H., He, J., Jin, Z., Liu, H., Pitting corrosion behavior and mechanism of 316L stainless steel induced by marine fungal extracellular polymeric substances. Corros. Sci., 2023; 224: 111485. 10.1016/j.corsci.2023.11148510.1016/j.corsci.2023.111485 ↗
4. Ghilan, A., Chiriac, A.P., Nita, L.E., Rusu, A.G., Neamtu, I., Chiriac, V.M., Trends in 3D printing processes for biomedical field: opportunities and challenges. J. Polym. Environ., 2020; 28: 1345–1367. 10.1007/s10924-020-01722-x10.1007/s10924-020-01722-x ↗
5. Li, H., Liu, W., Chen, L., Fan, P., Dong, B., Ma, Z., et al., Corrosion crack failure analysis of 316L hydraulic control pipeline in high temperature aerobic steam environment of heavy oil thermal recovery well. Eng. Fail. Anal., 2022; 138: 106297. 10.1016/j.engfailanal.2022.10629710.1016/j.engfailanal.2022.106297 ↗
6. Lin, H., Chen, C., Dong, P., Li, Q., Yang, Y., A novel inherent strain method for predicting residual stresses and deformations in metal additive manufacturing. Comput. Mech., 2025; 76: 1–17. 10.1007/s00466-025-02620-610.1007/s00466-025-02620-6 ↗
7. Kang, K., Liu, Y., Ren, H., Zhang, Q., Wang, S., Kong, Y., et al., A novel magnetic field assisted powder arc additive manufacturing for Ti60 titanium alloy: method, microstructure and mechanical properties. Addit. Manuf., 2024; 83: 104065. 10.1016/j.addma.2024.10406510.1016/j.addma.2024.104065 ↗
8. Farabi, E., Klein, T., Schnall, M., Primig, S., Effects of high deposition rate during cold metal transfer additive manufacturing on microstructure and properties of Ti-6Al-4V. Addit. Manuf., 2023; 71: 103592. 10.1016/j.addma.2023.10359210.1016/j.addma.2023.103592 ↗
9. Chahal, V., Taylor, R.M., A review of geometric sensitivities in laser metal 3D printing. Virtual. Phys. Prototyp., 2020; 15: 227–241. 10.1080/17452759.2019.170925510.1080/17452759.2019.1709255 ↗
10. Jandaghi, M.R., Pouraliakbar, H., Iannucci, L., Fallah, V., Pavese, M., Comparative assessment of gas and water atomized powders for additive manufacturing of 316 L stainless steel: Microstructure, mechanical properties, and corrosion resistance. Mater. Charact., 2023; 204: 113204. 10.1016/j.matchar.2023.11320410.1016/j.matchar.2023.113204 ↗
11. Kamath, C., El-Dasher, B., Gallegos, G.F., King, W.E., Sisto, A., Density of additively-manufactured, 316L SS parts using laser powder-bed fusion at powers up to 400 W. Int. J. Adv. Manuf. Technol., 2014; 74: 65–78. 10.1007/s00170-014-5954-910.1007/s00170-014-5954-9 ↗
12. Li, X., Roth, C.C., Tancogne-Dejean, T., Mohr, D., Rate-and temperature-dependent plasticity of additively manufactured stainless steel 316L: Characterization, modeling and application to crushing of shell-lattices. Int. J. Impact. Eng., 2020; 145: 103671. 10.1016/j.ijimpeng.2020.10367110.1016/j.ijimpeng.2020.103671 ↗
13. Zhang, Z., Chu, B., Wang, L., Lu, Z., Comprehensive effects of placement orientation and scanning angle on mechanical properties and behavior of 316L stainless steel based on the selective laser melting process. J. Alloys. Compd., 2019; 791: 166–175. 10.1016/j.jallcom.2019.03.08210.1016/j.jallcom.2019.03.082 ↗
14. Galy, C., Le Guen, E., Lacoste, E., Arvieu, C., Main defects observed in aluminum alloy parts produced by SLM: From causes to consequences. Addit. Manuf., 2018; 22: 165–175. 10.1016/j.addma.2018.05.00510.1016/j.addma.2018.05.005 ↗
15. Gong, H., Nadimpalli, V.K., Rafi, K., Starr, T., Stucker, B., Micro-CT evaluation of defects in Ti-6Al-4V parts fabricated by metal additive manufacturing. Technologies, 2019; 7: 44. 10.3390/technologies702004410.3390/technologies7020044 ↗
16. Zhao, J., Easton, M., Qian, M., Leary, M., Brandt, M., Effect of building direction on porosity and fatigue life of selective laser melted AlSi12Mg alloy. Mater. Sci. Eng. A, 2018; 729: 76–85. 10.1016/j.msea.2018.05.04010.1016/j.msea.2018.05.040 ↗
17. Larrosa, N.O., Wang, W., Read, N., Loretto, M.H., Evans, C., Carr, J., et al., Linking microstructure and processing defects to mechanical properties of selectively laser melted AlSi10Mg alloy. Theor. Appl. Fract. Mech., 2018; 98: 123–133. 10.1016/j.tafmec.2018.09.01110.1016/j.tafmec.2018.09.011 ↗
18. Vilaro, T., Colin, C., Bartout, J.D., As-fabricated and heat-treated microstructures of the Ti-6Al-4V alloy processed by selective laser melting. Metall. Mater. Trans. A, 2011; 42: 3190–3199. 10.1007/s11661-011-0731-y10.1007/s11661-011-0731-y ↗
19. Zhao, Z.Y., Li, L., Bai, P.K., Jin, Y., Wu, L.Y., Li, J., et al., The heat treatment influence on the microstructure and hardness of TC4 titanium alloy manufactured via selective laser melting. Materials, 2018; 11: 1318. 10.3390/ma1108131810.3390/ma11081318 ↗
20. Jones, R., Rans, C., Iliopoulos, A.P., Michopoulos, J.G., Phan, N., Peng, D., Modelling the variability and the anisotropic behaviour of crack growth in SLM Ti-6Al-4V. Materials, 2021; 14: 1400. 10.3390/ma1406140010.3390/ma14061400 ↗
21. Tan, Q., Fan, Z., Tang, X., Yin, Y., Li, G., Huang, D., et al., A novel strategy to additively manufacture 7075 aluminium alloy with selective laser melting. Mater. Sci. Eng. A, 2021; 821: 141638. 10.1016/j.msea.2021.14163810.1016/j.msea.2021.141638 ↗
22. Quelho de Macedo, R., Ferreira, R.T.L., Jayachandran, K., Determination of mechanical properties of FFF 3D printed material by assessing void volume fraction, cooling rate and residual thermal stresses. Rapid Prototyp. J., 2019; 25: 1661–1683. 10.1108/RPJ-08-2018-019210.1108/RPJ-08-2018-0192 ↗
23. Zhao, S., Yu, M., Yan, R., Zhai, Q., Liu, J., Dai, X., et al., Surface roughness and microhardness improvement of laser cladding stainless-steel 316 by laser polishing based on multiple remelting. Opt. Laser Technol., 2024; 176: 110903. 10.1016/j.optlastec.2024.11090310.1016/j.optlastec.2024.110903 ↗
24. Wang, L., Gao, M., Zhang, C., Zeng, X., Effect of beam oscillating pattern on weld characterization of laser welding of AA6061-T6 aluminum alloy. Mater. Des., 2016; 108: 707–717. 10.1016/j.matdes.2016.07.05310.1016/j.matdes.2016.07.053 ↗
25. Fetzer, F., Sommer, M., Weber, R., Weberpals, J.P., Graf, T., Reduction of pores by means of laser beam oscillation during remote welding of AlMgSi. Opt. Lasers Eng., 2018; 108: 68–77. 10.1016/j.optlaseng.2018.04.01210.1016/j.optlaseng.2018.04.012 ↗
26. Schultz, V., Seefeld, T., Vollertsen, F., Gap bridging ability in laser beam welding of thin aluminum sheets. Phys. Procedia, 2014; 56: 545–553. 10.1016/j.phpro.2014.08.03710.1016/j.phpro.2014.08.037 ↗
27. Tsukamoto, T., Kawanaka, H., Maeda, Y., Laser narrow gap welding of thick carbon steels using high brightness laser with beam oscillation. In: International Congress on Applications of Lasers & Electro-Optics. Laser Institute of America; 2011. pp. 141–146. 10.2351/1.506222710.2351/1.5062227 ↗
28. Mann, V., Hofmann, K., Schaumberger, K., Weigert, T., Schuster, S., Hafenecker, J., et al., Influence of oscillation frequency and focal diameter on weld pool geometry and temperature field in laser beam welding of high strength steels. Procedia CIRP, 2018; 74: 470–474. 10.1016/j.procir.2018.08.14810.1016/j.procir.2018.08.148 ↗
29. Li, J., Liu, Y., Tao, Y., Zhang, Q., Kang, K., Sun, Q., et al., Analysis of vapor plume and keyhole dynamics in laser welding stainless steel with beam oscillation. Infrared Phys. Technol., 2021; 113: 103536. 10.1016/j.infrared.2020.10353610.1016/j.infrared.2020.103536 ↗
30. Jiang, Z., Chen, X., Li, H., Lei, Z., Chen, Y., Wu, S., et al., Grain refinement and laser energy distribution during laser oscillating welding of Invar alloy. Mater. Des., 2020; 186: 108195. 10.1016/j.matdes.2019.10819510.1016/j.matdes.2019.108195 ↗
31. Zhang, C., Yu, Y., Chen, C., Zeng, X., Gao, M., Suppressing porosity of a laser keyhole welded Al-6Mg alloy via beam oscillation. J. Mater. Process. Technol., 2020; 278: 116382. 10.1016/j.jmatprotec.2019.11638210.1016/j.jmatprotec.2019.116382 ↗
32. Li, J., Sun, Q., Kang, K., Zhen, Z., Liu, Y., Feng, J., Process stability and parameters optimization of narrow-gap laser vertical welding with hot wire for thick stainless steel in nuclear power plant. Opt. Laser Technol., 2020; 123: 105921. 10.1016/j.optlastec.2019.10592110.1016/j.optlastec.2019.105921 ↗