journal article·2002Open access

Ternary Compound Ti3SiC2: Part I. Pulse Discharge Sintering Synthesis

ZhengMing Sun, ZheFeng Zhang, Hitoshi Hashimoto, Toshihiko Abe

MATERIALS TRANSACTIONS· Volume 43· Issue 3

Abstract

Pulse discharge sintering (PDS) technique was employed to synthesize the ternary compound Ti3SiC2 from four starting powder mixtures. The experimental results demonstrated that when the starting material of 3Ti/Si/2C or 3Ti/SiC/C was used high content of the secondary phase, TiC, higher than 30 mass%, was found in the sintered material. When TiC powder as starting material was used (Ti/Si/2TiC) in the same stoichiometric composition, however, the final sintered product contained low TiC content of a few percent. Further adjusting the composition to the off-stoichiometric of 2Ti/2Si/3TiC, the content of the secondary phase TiC was further controlled to be around 1 mass%. In the materials sintered from Ti/Si/2TiC and 2Ti/2Si/3TiC an optimum sintering temperature exists at 1573 K, at which the highest Ti3SiC2 phase purity was achieved. When sintered at the optimum temperature a density of higher than 99% was obtained. At the optimum sintering temperature, both the phase purity and the density of the material sintered from 2Ti/2Si/3TiC showed very little dependence on the sintering time ranging from a few minutes to four hours, indicating the phase stability at this temperature.
Source: openalex_inverted_index · Quality: baseline

Research context

OpenAlex topics: MXene and MAX Phase Materials · Advanced ceramic materials synthesis · Advanced materials and composites

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

National Institute of Advanced Industrial Science and Technology (AIST Tohoku)

References (18)

Show source-provided references
1. 1) W. Jeitschko and H. Nowotny: Monath. Chem. 98 (1967) 329–337.10.1007/BF00899949 ↗
2. 2) J. J. Nickl, K. K. Schweitzer and P. Luxenberg: J. Less Com. Met. 26 (1972) 335–353.10.1016/0022-5088(72)90083-5 ↗
3. 3) T. Goto and T. Hirai: Mater. Res. Bull. 22 (1987) 1195–1201.10.1016/0025-5408(87)90128-0 ↗
4. 4) M. Barsoum: Prog. Solid St. Chem. 28 (2000) 201–281.10.1016/S0079-6786(00)00006-6 ↗
5. 5) S. Arunajatesan and A. H. Carim: J. Am. Ceram. Soc. 78 (1995) 667–672.10.1111/j.1151-2916.1995.tb08230.x ↗
6. 6) J. Lis, Y. Miyamoto, R. Pampuch and K. Tanihata: Mater. Lett. 22 (1995) 163–168.10.1016/0167-577X(94)00246-0 ↗
7. 7) J. F. Li, F. Sato and R. Watanabe: J. Mater. Sci. Lett. 18 (1999) 1595–1597.10.1023/A:1006664416845 ↗
8. 8) M. W. Barsoum and T. El-Raghy: J. Am. Ceram. Soc. 79 (1996) 1953–1956.10.1111/j.1151-2916.1996.tb08018.x ↗
9. 9) T. El-Raghy and M. W. Barsoum: J. Am. Ceram. Soc. 82 (1999) 2849–2854.10.1111/j.1151-2916.1999.tb02166.x ↗
10. 10) Y. C. Zhou and Z. M. Sun: Scr. Mater. 41 (1999) 61–66.10.1016/S1359-6462(99)00054-8 ↗
11. 11) J. T. Li and Y. Miyamoto: J. Mater. Synth. Proc. 7 (1999) 91–96.10.1023/A:1021865613357 ↗
12. 12) J.-F. Li, W. Pan, F. Sato and R. Watanabe: Acta Mater. 49 (2001) 937–945.10.1016/S1359-6454(01)00011-8 ↗
13. 13) Z. F. Zhang, Z. M. Sun, H. Hashimoto and T. Abe: Submitted to J. Am. Ceram. Soc. 2001.
14. 14) Z. F. Zhang, Z. M. Sun, H. Hashimoto and T. Abe: Submitted to Mater. Res. Bull. 2001.
15. 15) Z. F. Zhang, Z. M. Sun, H. Hashimoto and T. Abe: Scr. Mater. 45 (2001) 1461–1467.10.1016/S1359-6462(01)01184-8 ↗
16. 16) Z. F. Zhang, Z. M. Sun, H. Hashimoto and T. Abe: Mater. Res. Innov. in press.
17. 17) Z. F. Zhang, Z. M. Sun, H. Hashimoto and T. Abe: Submitted to Acta Mater. 2001.
18. 18) L. Kaufman: Calphad 3 (1979) 45–76.10.1016/0364-5916(79)90020-8 ↗