journal article·2018-09-01Open access

Challenges in the Recycling of Precious Metals

Yoshihiro Kayanuma, Shoei Mizuhashi, Yuichiro Shindo

MATERIALS TRANSACTIONS· Volume 59· Issue 9

Abstract

Precious metals from industrial scraps generated by manufacturing processes have been extensively recycled. For these recycles, it is necessary to ensure confidentiality when dealing with the scraps and to perform the recycling operation in an isolated lot with a high recovery ratio, short operation time, and low treatment cost. In recent years, three challenges have emerged in scrap recycling. The first is the decrease in the precious metal content in the scrap, owing to the substitution of precious metals with other non-ferrous metals. The second is the contamination of the scrap with metals that are not present in natural ores. These contaminations pose challenges in the extraction and purification of precious metals. The third challenge is the adherence to Japan’s environmental regulations, which have been tightened recently, restricting the continuous use of some chemicals such as nitric acid. In this report, some efforts of precious metal recycling companies to overcome these challenges are discussed.
Source: openalex_inverted_index · Quality: baseline

Research context

OpenAlex topics: Extraction and Separation Processes · Recycling and Waste Management Techniques · Molten salt chemistry and electrochemical processes

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

Product Division, Matsuda Sangyo Co., Ltd.

Precious Metal Material Division, Matsuda Sangyo Co., Ltd.

References (22)

Show source-provided references
1. 1) J. Shibata and A. Okuda: Shigen-to-Sozai 118 (2002) 1–8.10.2473/shigentosozai.118.1 ↗
2. 2) T.H. Okabe, H. Nakada and K. Morita: J. Surf. Sci. Soc. Jpn. 29 (2008) 592–600.10.1380/jsssj.29.592 ↗
3. 3) T.H. Okabe and K. Nose: Mater. Cycles. Waste Manag. Res. 22 (2011) 50–57.10.3985/mcwmr.22.50 ↗
4. 4) A. Okuda and S. Shioda: J. Surf. Finish. Soc. Jpn. 53 (2002) 647–651.10.4139/sfj.53.647 ↗
5. 5) S. Mizuhashi and T. Honda: J. Surf. Finish. Soc. Jpn. 66 (2015) 81–85.10.4139/sfj.66.81 ↗
6. 6) T. Tachikawa: Indust 31 (2016) 16–20.
7. 7) M. Nanjo: Bulletin of the Research Institute of Mineral Dressing and Metallurgy, Tohoku University 43 (1988) 239–251.
8. 8) T. Uno, S. Terashima and K. Kimura: Materia Japan 50 (2011) 30–32.10.2320/materia.50.30 ↗
9. 9) Y. Miura: Materia Japan 46 (2007) 180–183.10.2320/materia.46.180 ↗
10. 10) J. Shibata: J. Surf. Finish. Soc. Jpn. 53 (2002) 641–646.10.4139/sfj.53.641 ↗
11. 11) H. Narita and M. Tanaka: J. MMIJ 127 (2011) 175–181.10.2473/journalofmmij.127.175 ↗
12. 12) S. Takizawa: J. Env. Conserv. Eng. 30 (2001) 902–906.10.5956/jriet.30.902 ↗
13. 13) T. Hoshino, H. Hirosawa, T. Matsukawa, T. Ogawa, Y. Ejiri, S. Tsuneda and A. Hirata: Journal Japan Biological Society of Water and Waste 40 (2004) 137–142.
14. 14) Y. Kinoshita: Japan J. Water Pollution Research 12 (1989) 79–86.10.2965/jswe1978.12.79 ↗
15. 15) T.H. Okabe, S. Yamamoto, Y. Kayanuma and M. Maeda: J. Mater. Res. 18 (2003) 1960–1967.10.1557/JMR.2003.0272 ↗
16. 16) T.H. Okabe, Y. Kayanuma, S. Yamamoto and M. Maeda: Mater. Trans. JIM 44 (2003) 1386–1393.10.2320/matertrans.44.1386 ↗
17. 17) Y. Kayanuma, T.H. Okabe, Y. Mitsuda and M. Maeda: J. Alloys Compd. 365 (2004) 211–220.10.1016/S0925-8388(03)00666-2 ↗
18. 18) Y. Kayanuma, T.H. Okabe and M. Maeda: Metall. Mater. Trans. B 35 (2004) 817–824.10.1007/s11663-004-0075-8 ↗
19. 19) H. Sasaki and M. Maeda: J. Japan Inst. Met. Mater. 75 (2011) 602–606.10.2320/jinstmet.75.602 ↗
20. 20) C. Horike, K. Morita and T.H. Okabe: Metall. Mater. Trans. B 43 (2012) 1300–1307.10.1007/s11663-012-9746-z ↗
21. 21) R. Kasuya, T. Miki and Y. Tai: J. Ceram. Soc. Jpn. 121 (2013) 261–264.10.2109/jcersj2.121.261 ↗
22. 22) R. Kasuya, T. Miki, H. Morikawa and Y. Tai: Metall. Mater. Trans. B 46 (2015) 2476–2483.10.1007/s11663-015-0431-x ↗