journal article·2024-08-01Open access

Separation of Palladium and Rhodium from the Spent Metal-Honeycomb Catalysts by Pulsed Discharge without Chemical Additives

Chiharu Tokoro, Yuto Imaizumi, Taketoshi Koita, Akiko Kubota, Yutaro Takaya, Keishi Oyama, Md. Mijanur Rahman

MATERIALS TRANSACTIONS· Volume 65· Issue 8

Abstract

One of the main causes of atmospheric pollution comes from mobile sources that emit noxious gases from internal combustion engines. For the suppression of toxic exhaust gases, a catalytic converter is used as an anti-pollution device, because it catalyzes or accelerates the degradation of emissions making them less harmful. In the catalytic converter, platinum (Pt), palladium (Pd) and rhodium (Rh) catalysts are normally used for their excellent performances. However, these metals are expensive, rare, and scarce in the earth’s crust. These precious metals thus emphasized the importance of developing efficient recycling practices. For the recycling of these precious metals, a very fast, easy, economical, environmentally friendly and high-safety electric pulse discharge method was used to separate the Pd and Rh from the spent metal-honeycomb (MH) catalytic converter consisting of p as the catalyst carrier. To standardize the precious metals recycling process and attain the highest level of separation of Pd and Rh, electric pulse shots ranging from 120–240 and standoff distances (gap width between the positive electrode and the sample surface) ranging from 5–10 mm were applied. During this process, an electrical explosion occurred within the honeycomb structures through the electric shock. After the electrical explosion, the particles are collected, then sieved and physical characterizations are performed. Scanning electron microscope (SEM) and energy dispersive spectroscopy (EDX) analyses revealed that the most separated particles are highly pure, and dispersed homogeneously without destroying particle structures. In this article, we first report about 87.91% of Pd and 90.77% of Rh are separated from each catalytic converter using the electric pulse discharge method that can overcome challenges and achieve ambitious recycling targets in the recycling industry. The effects of the discharge energies and the shock energy determined by varying electric pulse shots and standoff distance, respectively, are discussed. These findings provide insight into the recovery of precious metals for electric pulse discharge and play a role in developing a very effective recycling method not only for the catalytic converter but also for other devices.
Source: openalex_inverted_index · Quality: baseline

Research context

OpenAlex topics: Advanced materials and composites

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

Faculty of Science and Engineering, Waseda University

Faculty of Engineering, The University of Tokyo

Graduate School of Creative Science and Engineering, Waseda University

Waseda Research Institute for Science and Engineering, Waseda University

Research Institute of Environment and Resources Circulation, Waseda University

References (26)

Show source-provided references
1. 1) S. Dey and N.S. Mehta: Automobile pollution control using catalysis, Resources, Environment and Sustainability 2 (2020) 100006. doi:10.1016/j.resenv.2020.10000610.1016/j.resenv.2020.100006 ↗
2. 2) R. Manojkumar, S. Haranethra, M. Muralidharan and A. Ramaprabhu: I.C. Engine emission reduction using catalytic converter by replacing the noble catalyst and using copper oxide as the catalyst, Mater. Today: Proc. 45 (2021) 769–773. doi:10.1016/j.matpr.2020.02.80410.1016/j.matpr.2020.02.804 ↗
3. 3) H. Hamada and M. Haneda: A review of selective catalytic reduction of nitrogen oxides with hydrogen and carbon monoxide, Appl. Catal. A Gen. 421–422 (2012) 1–13. doi:10.1016/j.apcata.2012.02.00510.1016/j.apcata.2012.02.005 ↗
4. 4) C.A. Nogueira, A.P. Paiva, P.C. Oliveira, M.C. Costa and A.M. Rosa da Costa: Oxidative leaching process with cupric ion in hydrochloric acid media for recovery of Pd and Rh from spent catalytic converters, J. Hazard. Mater. 278 (2014) 82–90. doi:10.1016/j.jhazmat.2014.05.09910.1016/j.jhazmat.2014.05.099 ↗
5. 5) M. Haneda, M. Sasaki, H. Hamada and M. Ozawa: Platinum-Based Catalyst for Diesel Hydrocarbon Oxidation, Chin. J. Catal. 32 (2011) 777–781. doi:10.1016/S1872-2067(10)60192-110.1016/S1872-2067(10)60192-1 ↗
6. 6) M. Jia, G. Jiang, H. Chen, Y. Pang, F. Yuan, Z. Zhang, N. Miao, C. Zheng, J. Song, Y. Li and H. Wang: Recent Developments on Processes for Recovery of Rhodium Metal from Spent Catalysts, Catalysts 12 (2022) 1415. doi:10.3390/catal1211141510.3390/catal12111415 ↗
7. 7) T. Hirakawa, Y. Shimokawa, W. Tokuzumi, T. Sato, M. Tsushida, H. Yoshida, J. Ohyama and M. Machida: Multicomponent 3d Transition-Metal Nanoparticles as Catalysts Free of Pd, Pt, or Rh for Automotive Three-Way Catalytic Converters, ACS Appl. Nano Mater. 3 (2020) 9097–9107. doi:10.1021/acsanm.0c0176910.1021/acsanm.0c01769 ↗
8. 8) E. Kritsanaviparkporn, F.M. Baena-Moreno and T.R. Reina: Catalytic Converters for Vehicle Exhaust: Fundamental Aspects and Technology Overview for Newcomers to the Field, Chemistry 3 (2021) 630–646. doi:10.3390/chemistry302004410.3390/chemistry3020044 ↗
9. 9) A. Deep, A.L. Sharma, G.C. Mohanta, P. Kumar and K.-H. Kim: A facile chemical route for recovery of high quality zinc oxide nanoparticles from spent alkaline batteries, Waste Manag. 51 (2016) 190–195. doi:10.1016/j.wasman.2016.01.03310.1016/j.wasman.2016.01.033 ↗
10. 10) Y. Guo, F. Li, H. Zhu, G. Li, J. Huang and W. He: Leaching lithium from the anode electrode materials of spent lithium-ion batteries by hydrochloric acid (HCl), Waste Manag. 51 (2016) 227–233. doi:10.1016/j.wasman.2015.11.03610.1016/j.wasman.2015.11.036 ↗
11. 11) H.A. Petersen, T.H.T. Myren, S.J. O’Sullivan and O.R. Luca: Electrochemical methods for materials recycling, Mater. Adv. 2 (2021) 1113–1138. doi:10.1039/D0MA00689K10.1039/D0MA00689K ↗
12. 12) P.G. Schiavi, F.C. dos Santos Martins Padoan, P. Altimari and F. Pagnanelli: Cryo-Mechanical Treatment and Hydrometallurgical Process for Recycling Li-MnO2 Primary Batteries with the Direct Production of LiMnPO4 Nanoparticles, Energies 13 (2020) 4004. doi:10.3390/en1315400410.3390/en13154004 ↗
13. 13) C. Duan, X. Wen, C. Shi, Y. Zhao, B. Wen and Y. He: Recovery of metals from waste printed circuit boards by a mechanical method using a water medium, J. Hazard. Mater. 166 (2009) 478–482. doi:10.1016/j.jhazmat.2008.11.06010.1016/j.jhazmat.2008.11.060 ↗
14. 14) V. Oestreicher, C.S. García, R. Pontiggia, M.B. Rossi, P.C. Angelomé and G.J.A.A. Soler-Illia: E-waste upcycling for the synthesis of plasmonic responsive gold nanoparticles, Waste Manag. 117 (2020) 9–17. doi:10.1016/j.wasman.2020.07.03710.1016/j.wasman.2020.07.037 ↗
15. 15) M. Kondo, S. Lim, T. Koita, T. Namihira and C. Tokoro: Application of electrical pulsed discharge to metal layer exfoliation from glass substrate of hard-disk platter, Results Eng. 12 (2021) 100306. doi:10.1016/j.rineng.2021.10030610.1016/j.rineng.2021.100306 ↗
16. 16) M.N. Le and M.S. Lee: A Review on Hydrometallurgical Processes for the Recovery of Valuable Metals from Spent Catalysts and Life Cycle Analysis Perspective, Miner. Process. Extr. Metall. Rev. 42 (2021) 335–354. doi:10.1080/08827508.2020.172691410.1080/08827508.2020.1726914 ↗
17. 17) S. Harjanto, Y. Cao, A. Shibayama, I. Naitoh, T. Nanami, K. Kasahara, Y. Okumura, K. Liu and T. Fujita: Leaching of Pt, Pd and Rh from Automotive Catalyst Residue in Various Chloride Based Solutions, Mater. Trans. 47 (2006) 129–135. doi:10.2320/matertrans.47.12910.2320/matertrans.47.129 ↗
18. 18) J.E. Terrazas-Rodríguez, S. Gutiérrez-Granados, M.A. Alatorre-Ordaz, C. Ponce de León and F.C. Walsh: A comparison of the electrochemical recovery of palladium using a parallel flat plate flow-by reactor and a rotating cylinder electrode reactor, Electrochim. Acta 56 (2011) 9357–9363. doi:10.1016/j.electacta.2011.08.02110.1016/j.electacta.2011.08.021 ↗
19. 19) T. Koita, M. Kondo, S. Lim, M. Inutsuka, T. Namihira, S. Oyama and C. Tokoro: Application of Simple Notch to Selective Separation of Adherend Bonded With Resin Adhesive by Pulsed Discharge in Air, IEEE Trans. Plasma Sci. 49 (2021) 3860–3872. doi:10.1109/TPS.2021.312674010.1109/TPS.2021.3126740 ↗
20. 20) K. Teruya, S. Lim, K. Mochidzuki, T. Koita, F. Mizumoto, M. Asao, T. Namihira and C. Tokoro: Utilization of underwater electrical pulses in separation process for recycling of positive electrode materials in lithium-ion batteries: Role of sample size, Int. J. Plasma Environ. Sci. Technol. 16 (2022) e01003. doi:10.34343/ijpest.2022.16.e0100310.34343/ijpest.2022.16.e01003 ↗
21. 21) Y. Liu, Z. Li, X. Li, G. Zhou, H. Li, Q. Zhang and F. Lin: Energy Transfer Efficiency Improvement of Liquid Pulsed Current Discharge by Plasma Channel Length Regulation Method, IEEE Trans. Plasma Sci. 45 (2017) 3231–3239. doi:10.1109/TPS.2017.265110510.1109/TPS.2017.2651105 ↗
22. 22) H. Bluhm: Power Systems, (Springer-Verlag, Berlin, 2006).
23. 23) S. Lim, Y. Imaizumi, K. Mochidzuki, T. Koita, T. Namihira and C. Tokoro: Recovery of Silver From Waste Crystalline Silicon Photovoltaic Cells by Wire Explosion, IEEE Trans. Plasma Sci. 49 (2021) 2857–2865. doi:10.1109/TPS.2021.310630710.1109/TPS.2021.3106307 ↗
24. 24) Y.E. Krasik et al.: Underwater Electrical Explosion of Wires and Wire Arrays and Generation of Converging Shock Waves, IEEE Trans. Plasma Sci. 44 (2016) 412–431. doi:10.1109/TPS.2015.251375710.1109/TPS.2015.2513757 ↗
25. 25) T. Fujita, I. Yoshimi, A. Shibayama, T. Miyazaki, K. Abe, M. Sato, W.T. Yen and J. Svoboda: Crushing and Liberation of Materials by Electrical Disintegration, Eur. J. Miner. Process. Environ. Prot. 1 (2001) 113–122.
26. 26) C.L. Duan, Z.J. Diao, Y.M. Zhao and W. Huang: Liberation of valuable materials in waste printed circuit boards by high-voltage electrical pulses, Miner. Eng. 70 (2015) 170–177. doi:10.1016/j.mineng.2014.09.01810.1016/j.mineng.2014.09.018 ↗