journal article·2004Open access

Slip Casting of Titanium Powder for Dental Prosthetic Appliances

Shoji Ohkawa, Kuniyoshi Ishii, Motohiro Uo, Toshi Sugawara, Fumio Watari

MATERIALS TRANSACTIONS· Volume 45· Issue 4

Abstract

The feasibility of using slip casting of titanium powder as a method for manufacturing dental prosthetic appliances was examined. Slips with water-powder (W/P) ratios, 0.318, 0.354 and 0.391, and with minimum viscosities were cast in plaster molds. Castings were sintered in an argon atmosphere at 1373, 1473 and 1573 K for 3.6, 7.2 and 10.8 ks, respectively. Green densities and strengths of castings were 2.20 kg/m3 and 2.31—3.82 MPa, respectively. Linear shrinkages and relative densities of sintered castings varied from 17.6 to 20.8% and 0.82 to 0.97 of the theoretical density of titanium, respectively. Tensile strengths and Vickars hardness of the sintered castings were 199.5—315.4 MPa and 233.0—247.7, respectively. There was almost no elongation. Decreasing porosity and crystal grain growth were found in the microstructures of sintered castings and rod-like precipitates of TiC with α-titanium were also observed. Concentrations of carbon and oxygen in the microstructures of sintered castings were higher than those in wrought titanium. Fractured surfaces showed ridge patterns typical of brittle fracture. Further modification of the sintering atmosphere and the additives for the slip is needed to improve the microstructure of slip-cast sintered titanium.
Source: openalex_inverted_index · Quality: baseline

Research context

OpenAlex topics: Dental materials and restorations · Dental Implant Techniques and Outcomes · Bone Tissue Engineering Materials

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

Department of Oral Health Science, Division of Dental Materials and Engineering, Graduate School of Dental Medicine, Hokkaido University

Department of Materials Engineering, Division of Materials Science and Engineering, Graduate School of Engineering, Hokkaido University

References (43)

Show source-provided references
1. 1) D.F. Williams: Biocompatibility of Clinical Implant Materials, (CRC Press, Inc Boca Raton, Florida, 1984) pp.7-44.
2. P.-I. Bränemark · J. Prosthet. Dent. · 1983 · 50 · 39910.1016/S0022-3913(83)80101-2 ↗
3. E.D. Rekow · J. Prosthet. Dent. · 1987 · 58 · 51210.1016/0022-3913(87)90285-X ↗
4. F. Duret et al. · J. Am. Dent. Assoc. · 1988 · 117 · 71510.14219/jada.archive.1988.0096 ↗
5. T. Sohmura, J. Takahashi · J. Jpn. Dent. Mater. · 1994 · 13 · 61
6. 6) R.M. Waterstrat: Publication No.(NIH) 77-1227, (US. Dept.Health, Education and Welfare, Washington DC) (1977) 224-233.
7. T. Togaya, M. Suzuki, K. Ida, M. Na · J. Jpn. Dent. Mater. · 1985 · 4 · 344
8. K. Ida, T. Togaya and M. Suzuki · J. Jpn. Dent. Mater. · 1983 · 2 · 765
9. E.H. Greener, J.B. Moser, J. Opp, K · J. Dent. Res. · abst · 65 · 317
10. H. Hashimoto, A. Kuroiwa, K. Wada, · J. Jpn. Dent. Mater. · 1992 · 11 · 603
11. 11) I. Miura and K. Ida et al.: Chitan no Shika Riyou (Quintencence Book, Tokyo, Japan, 1988) pp.161-266. (in Japanese).
12. T. Okabe and H. Herø · Cell and Mat. · 1995 · 5 · 211
13. Y. Oda · J. Jpn. Dent. Mater. · 1984 · 3 · 376
14. W.S. Lee · J. Jpn. Dent. Mater. · 1995 · 14 · 142
15. R.A. Fuy, JR, R.G. Craig and K. Asg · J. Oral. Rehabil. · 1976 · 3 · 15110.1111/j.1365-2842.1976.tb00939.x ↗
16. 16) W.D. Kingery et al.: Ceramic fabrication processes, (The M.I.T. Press, Cambridge, Massachusetts, 1968) pp.5-51.
17. P.E. Rempes, B.C. Weber and M.A. Sc · Cera. Bull. · 1958 · 37 · 334
18. W.E. Hauth · J. Am. Cera. Soc. · 1949 · 32 · 39410.1111/j.1151-2916.1949.tb18919.x ↗
19. 19) ASM: ASM Handbook, Vol.7, 1st ed., (ASM International, Ohio, 1998) 162-163.
20. 20) T. Nakagawa and H. Kanbe: Rheology, 8th ed., (Misuzu Shobo Co., Tokyo, 1969) pp.624-627.
21. F.H. Norton, A.L. Johnson and W.G. · J. Am. Ceram. Soc. · 1944 · 27 · 14910.1111/j.1151-2916.1944.tb14885.x ↗
22. 22) H.V. Sulinski: U.S, Govern Res. Re. AD 432235, (1964) 26PP.
23. H.H. Hausner and D.P. Ferriss · Materials & Methods · 1956 · 43 · 132
24. 10.1111/j.1151-2916.1988.tb05855.x10.1111/j.1151-2916.1988.tb05855.x ↗
25. W.E. Hauth · J. Phys. Colloid Chem · 1950 · 54 · 14210.1021/j150475a012 ↗
26. 26) S. Glasstone and D. Lewis: Elements of Physical Chemistry, 2nd ed., (D.V. Nostrand Co. Maruzen Co., Tokyo, 1968) pp.579-580.
27. P.D.S. St. Pierre · Trans. Brit. Ceram. Soc · 1952 · 51 · 260
28. 28) P.D.S. St. Pierre: Proc. 3rd annual conf.; Reactive Metal,ed. by W.R. Clough, (Interscience, Buffalo, New York,1958) pp.93-107.
29. 29) M.J. Jr. Donachie: Titanium a technical guide, 2nd ed., (ASM, International, Materials Park, Ohio, 2000) pp.96-97.10.31399/asm.tb.ttg2.9781627082693 ↗
30. 30) ASM: Metals Handbook, Vol.9, 9ed., (ASM, Metals Park, Ohio, 1984) pp.308-321.
31. 31) W.D. Kingery etal: Ceramic fabrication processes, 4th ed., (The M.I.T. Press, Cambridge, Massachusetts, 1968) pp.120-131.
32. W. Raja and R.F. Boehm · J. Den. Res. · 1974 · 53 · 135110.1177/00220345740530061001 ↗
33. 33) ASM: Metals Handbook, Vol.7, 9ed (ASM, Metals Park, Ohio, 198) pp.309-310.
34. 34) W.D. Kingery: Kinetics of high-temperature processes, The M.I.T. Press, Cambridge, Massachusetts, John Wiley Sons, New York, Chapman & Hall, London, 1959) pp.158-159.
35. 35) ASM: Metals Handbook, Vol.4, 8ed. (ASM, Metals Park, Ohio, 1986) pp.455-457.
36. H.H. Hausner · J. Jpn. Soc. Powder and Powder Metall. · 1960 · 7 · 5810.2497/jjspm.7.58 ↗
37. 37) Akechi, K., and Hara, Z.:Proc. 2nd Int. Conf. on Titanium'80, Science and Technology, vol.3. (Metall Soc.AIME, 1973) 2255-2263.
38. H. Kyogoku, T. Toda and K. Shinohar · J. Jpn. Soc. Powder and Powder Metall. · 1993 · 40 · 440
39. KYOGOKU HIDEKI · J. Jpn. Soc. Powder and Powder Metall. · 1995 · 42 · 105210.2497/jjspm.42.1052 ↗
40. KONO TOMIO · J. Jpn. So. Powder and Powder Metall. · 1997 · 44 · 98510.2497/jjspm.44.985 ↗
41. MAJIMA KAZUHIKO · J. Jpn. Soc. Powder and Powder Metall. · 1986 · 33 · 2810.2497/jjspm.33.28 ↗
42. KUSAKA KATSUSHI · J. Jpn. Soc. Powder and Powder Metall. · 1995 · 42 · 38310.2497/jjspm.42.383 ↗
43. 43) JSA: JIS H 4650, (JSA, 2001) pp.1-16.