journal article·2012Open access

Reliability Enhancement of Thick Al–Cu Wire Bonds in IGBT Modules Using Al2Cu Precipitates

Toshiki Kurosu, Khyoupin Khoo, Yoshihide Nakamura, Keisuke Ozaki, Nobuhiro Ishikawa, Jin Onuki

MATERIALS TRANSACTIONS· Volume 53· Issue 2

Abstract

The reliability enhancement of Al wire bonds used in the insulated gate bipolar transistor (IGBT) modules is crucial to raise their reliability at the high operating temperatures of the motor vehicles in which the modules are widely used because cracking can occur in the Al. We investigated the bonding reliability of thick Al–0.5 mass% Cu wires, inside of which very fine Al2Cu phases precipitated in both grain boundaries and the Al matrix. We found the reliability of the aged Al–Cu wire bonds was much better than the reliabilities for Al–Cu wire bonds without aging and conventional Al–Ni wire bonds for temperature change ΔT of 50 K. We also found from thermal cycle test results that Al2Cu precipitates prevented crack propagation due to thermal expansion mismatch between Al wires and Si substrate.
Source: openalex_inverted_index · Quality: baseline

Research context

OpenAlex topics: Silicon Carbide Semiconductor Technologies · Electromagnetic Compatibility and Noise Suppression · Silicon and Solar Cell Technologies

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

Power and Industrial Division, Hitachi Ltd.

Graduate School of Science and Engineering, Ibaraki University

Department of Materials Science, Faculty of Engineering, Ibaraki University

The National Institute for Materials Science

References (13)

Show source-provided references
1. 1) J. Onuki, M. Koizumi and M. Suwa: IEEE Trans. Adv. Packag. 23 (2000) 108.10.1109/6040.826768 ↗
2. 2) M. Mori, R. Saitou and T. Yatsuo: Proc. 5th ISPSD, (1993) p. 287.
3. 3) J. Onuki, Y. Chonan, T. Komiyama, M. Nihei, R. Saitou, M. Suwa and T. Morita: Jpn. J. Appl. Phys. 40 (2001) 3985.10.1143/JJAP.40.3985 ↗
4. 4) Y. Shimizu, Y. Tomota, J. Onuki, K. P. Khoo and T. Kurosu: Jpn. J. Appl. Phys. 48 (2009) 066511.10.1143/JJAP.48.066511 ↗
5. 5) T. Kurosu, Y. Shimizu, Y. Tomota and J. Onuki: Mater. Trans. 52 (2011) 102–107.10.2320/matertrans.M2010308 ↗
6. 6) M. Ciappa: Microelectron. Reliab. 42 (2002) 653.10.1016/S0026-2714(02)00042-2 ↗
7. 7) W. Wu, M. Held, P. Jacob, P. Scacco and A. Birolini: Proc. 7th ISPSD, (1995) p. 330.
8. 8) S. Sumi, K. Ohga and K. Shirai: Proc. Int. Symp. Testing Failure Anal., (1989) p. 309.
9. 9) J. Onuki, M. Koizumi and J. Echigoya: Mater. Trans. JIM 37 (1996) 1324.10.2320/matertrans1989.37.1324 ↗
10. 10) Y. Koubuchi: Doctoral Thesis, Faculty of Engineering, Hokkaido University, (1997).
11. 11) R. E. Smallman: Physical Metallurgy, (Butterworth, London, 1962) p. 299.
12. 12) The Japan Institute of Metals: Materials Data Book, (Maruzen, Tokyo, 2004) p. 196 [in Japanese].
13. 13) M. Hansen: Constitution of Binary Alloys, (McGraw-Hill, New York, 1958) p. 87.10.1149/1.2428700 ↗