Relation of Shunting Current at Cracked Part to Critical Current and n-Value in Multifilamentary Bi2223 Composite Tape
Source abstract
Abstract
Relation of transport current and n-value to collective crack-induced current shunting in BSCCO (Bi2223) multi-filamentary composite tape pulled in tension was studied experimentally and analytically. For analysis, the partial crack-current shunting model of Fang et al. was used by placing the collective crack as the partial one. It was shown that (a) collective crack-induced shunting current increases with increasing current (and voltage) and with increasing collective crack size, (b) the transport current normalized with respect to the transport current in non-cracked state is described with the modified ratio of non-cracked area to overall cross-sectional area of superconducting filaments at low voltage where shunting current is low, while it deviates upward from the modified ratio at high voltage where the shunting current is enhanced, and (c) the enhanced shunting current acts to reduce n-value at high voltage. These features were similar to those of cracked coated conductor.
Source: openalex_inverted_index · Quality: baseline
Research context
OpenAlex topics: Mechanical stress and fatigue analysis · Electrical Contact Performance and Analysis · Thermal Analysis in Power Transmission
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
Affiliations
Department of Materials Science and Engineering, Kyoto University
High Energy Accelerator Research Organization (KEK), Cryogenics Science Center, J-PARC Center
Research Institute for Applied Sciences
American Superconductor Corporation
References (10)
Show source-provided references
1. 1) S. Ochiai, T. Nagai, H. Okuda, S.-S. Oh, M. Hojo, M. Tanaka, M. Sugano and K. Osamura: Supercond. Sci. Technol. 16 (2003) 988–994.10.1088/0953-2048/16/9/305 ↗
2. 2) S. Ochiai, T. Ishida, D. Doko, K. Morishita, H. Okuda, S.-S. Oh, D.-W. Ha, M. Hojo, M. Tanaka, M. Sugano and K. Osamura: Supercond. Sci. Technol. 18 (2005) S356–S363.10.1088/0953-2048/18/12/004 ↗
3. 3) A. Kelly and W. R. Tyson: J. Mech. Phys. Solids 13 (1965) 329–350.10.1016/0022-5096(65)90035-9 ↗
4. 4) S. Ochiai: Mechanical Properties of Metallic Composites, ed. by S. Ochiai, (Marcel Dekker Inc., New York, 1993) pp. 473–510.10.1201/9781482293487 ↗
5. 5) S. Ochiai and M. Hojo: J. Mater. Sci. 31 (1996) 3861–3869.10.1007/BF00352803 ↗
6. 6) Y. Miyoshi, E. P. A. Van Lanen, M. M. Dhallé and N. Nijhuits: Supercond. Sci. Technol. 22 (2009) 085009.10.1088/0953-2048/22/8/085009 ↗
7. 7) S. Ochiai, T. Arai, A. Toda, H. Okuda, M. Sugano, K. Osamura and W. Prusseit: J. Appl. Phys. 108 (2010) 063905.10.1063/1.3488014 ↗
8. 8) S. Ochiai, H. Okuda, T. Arai, S. Nagano, M. Sugano and W. Prusseit: Cryogenics 51 (2011) 584–590.10.1016/j.cryogenics.2011.08.003 ↗
9. 9) Y. Fang, S. Danyluk and M. T. Lanagan: Cryogenics 36 (1996) 957–962.10.1016/S0011-2275(96)00069-0 ↗
10. 10) A. Otto, E. J. Harley and R. Marson: Supercond. Sci. Technol. 18 (2005) S308–S312.10.1088/0953-2048/18/12/014 ↗