journal article·2018Open access

Evaluation of Wrinkling States Using In-Process Ultrasonic Examination during Sheet Metal Forming

Ryota Kakinoki, Yuji Segawa, Yasuo Marumo, Yasuhiro Imamura, Tomohiro Nonaka, Yutaka Sakata

MATERIALS TRANSACTIONS· Volume 59· Issue 5

Abstract

In press forming, sampling inspection has been performed during production. However, in sampling inspection, there is the possibility that defective products will proceed to the next process despite inspection. In this paper, we investigated a method for detecting wrinkle defects occurring during deep drawing in order to prevent the outflow of defective products. Deep-drawing tests were performed using a drawing die incorporating an ultrasonic transducer. During deep drawing, ultrasonic waves were irradiated to the interface between the die and the workpiece, and the occurrence of wrinkles was examined on the basis of ultrasonic reflection characteristics. The ultrasonic reflection intensity was changed by the occurrence of the wrinkles. The influence of wrinkle height and wrinkle wavelength on relative reflection intensity was shown. It was demonstrated that ultrasonic measurement is an effective method of detecting wrinkles during press forming.
Source: openalex_inverted_index · Quality: baseline

Research context

OpenAlex topics: Metal Forming Simulation Techniques · Laser and Thermal Forming Techniques · Metallurgy and Material Forming

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

Graduate School of Science and Technology, Kumamoto University

Department of Mechanical Engineering, National Institute of Technology, Miyakonojo College

Faculty of Advanced Science and Technology, Kumamoto University

Technical Division, Faculty of Engineering, Kumamoto University

Department of Integrated System Engineering, Nishinippon Institute of Technology

References (11)

Show source-provided references
1. 1) T. Yoshida: J. Jpn. Soc. Technol. Plast. 51 (2010) 865–869 (in Japanese).10.9773/sosei.51.865 ↗
2. 2) J. Koyama and M. Yang: J. Jpn. Soc. Technol. Plast. 51 (2010) 898–902 (in Japanese).10.9773/sosei.51.898 ↗
3. 3) N. Mahayotsanun, S. Sah, J. Cao, M. Peshkin, R.X. Gao and C.-T. Wang: Int. J. Mach. Tools Manuf. 49 (2009) 634–644.10.1016/j.ijmachtools.2009.01.009 ↗
4. 4) H. Saiki, Y. Sakata, S. Satonaka, Y. Marumo and Z.H. Zhan: Trans. Jpn. Soc. Mech. Eng., Ser. C 59 (1993) 1934–1939 (in Japanese).10.1299/kikaic.59.1934 ↗
5. 5) S. Stancu-Niederkorn, U. Engel and M. Geiger: J. Mater. Process. Technol. 45 (1994) 613–618.10.1016/0924-0136(94)90407-3 ↗
6. 6) N. Hagino, J. Endou, S. Katoh and M. Ishihama: J. Jpn. Soc. Technol. Plast. 54 (2013) 826–830 (in Japanese).10.9773/sosei.54.826 ↗
7. 7) N. Hagino, J. Endou, M. Ishihama, S. Komiya and S. Katoh: Procedia Eng. 81 (2014) 1073–1078.10.1016/j.proeng.2014.10.143 ↗
8. 8) S. Nishimoto and N. Shinke: J. Jpn. Soc. Non-Destr. Insp. 54 (2005) 557–561 (in Japanese).
9. 9) T. Nonaka, Y. Sakata, Y. Marumo, Y. Okinishi, T. Horinouchi, I. Ogawa and S. Watanabe: Appl. Mech. Mater. 182–183 (2012) 472–476.10.4028/www.scientific.net/AMM.182-183.472 ↗
10. 10) T. Nonaka, Y. Sakata, Y. Marumo, Y. Okinishi, H. Horinouchi, I. Ogawa and S. Watanabe: Steel Res. Int. Special Edition (2012) 387–390.
11. 11) Y. Tanimura: Etoki-Choompa-Tansho-Kiso-No-Kiso (Nikkan-kogyo-Shimbun-Sha, Tokyo, 2013) pp. 36–39 (in Japanese).