journal article·2019-01-01Open access

Effect of Solidification Conditions on the Deformation Behavior of Pure Copper Castings

Ikuzo Goto, Setsuo Aso, Ken-ichi Ohguchi, Kengo Kurosawa, Hiroyuki Suzuki, Hiroyuki Hayashi, Jun-ichi Shionoya

MATERIALS TRANSACTIONS· Volume 60· Issue 1

Abstract

The effect of solidification conditions on the tensile deformation behavior of pure copper castings for electrical parts was investigated. Two main types of tensile deformation properties were distinguished on the basis of the difference in uniform elongation. For the castings fabricated under a superheat of 100°C or 150°C, larger and smaller uniform elongation types corresponded to the absence and presence, respectively, of the Cu–Cu2O eutectic phase in the microstructure. Meanwhile, for the castings fabricated under a superheat of 50°C, greater uniform elongation was sometimes obtained when the eutectic phase was present. In addition, irrespective of the presence or absence of the eutectic phase, greater uniform elongation was always obtained when chills were used. Cross-sectional observations showed the existence of considerable nonspherical porosity when the eutectic phase was present; the porosity was reduced when the pouring was conducted under the superheat of 50°C and when the chills were used because of lower hydrogen content in the melt and supersaturation of the hydrogen by rapid cooling, respectively. These results suggest that not only the presence of the eutectic phase but also the inferior casting soundness due to the existence of the porosity is a dominant factor responsible for the decrease in the uniform elongation. The findings presented here indicate that a decrease in the hydrogen content in the melt and/or the rapid cooling during solidification are effective measures to stably achieve practically sufficient deformation properties along with superior casting soundness.
Source: openalex_inverted_index · Quality: baseline

Research context

OpenAlex topics: Aluminum Alloy Microstructure Properties · Aluminum Alloys Composites Properties · Metal Forming Simulation Techniques

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

Department of Materials Science, Graduate School of Engineering Science, Akita University

Akita Industrial Technology Center

Sanwa Tekki Corporation

References (18)

Show source-provided references
1. 1) M. Goto: Tetsu-to-Hagané 72 (1986) 1481–1487.10.2355/tetsutohagane1955.72.10_1481 ↗
2. 2) H. Ueno: J. JFS 73 (2001) 469–474.
3. 3) M. Suzuki, T. Tashiro and S. Eguchi: Reports of the 157th JFS Meeting, (2010) p. 62.
4. 4) Dogokin-imono-no-seisangijutsu-kaiteiban-henshuiinkai: Dogokin-imono-no-seisangijutsu, (The Materials Process Technology Center, Tokyo, 2014) pp. 70–71, 90, 102, 159, 268–269.
5. 5) I. Goto, K. Kurosawa, K. Ohguchi, S. Aso, H. Suzuki, H. Hayashi and J. Shionoya: J. Japan Inst. Met. Mater. 79 (2015) 511–517.10.2320/jinstmet.J2015042 ↗
6. 6) I. Goto, S. Aso, K. Ohguchi, H. Oguri, K. Kurosawa, H. Suzuki, H. Hayashi and J. Shionoya: J. Japan Inst. Met. Mater. 81 (2017) 133–142.10.2320/jinstmet.J2016052 ↗
7. 7) G. Petzow: Metallographisches keramographisches plastographisches Ätzen, (Nikkan Kogyo Shimbun, Tokyo, 1997) p. 114.
8. 8) H. Ueno and N. Ukai: IMONO 46 (1973) 57–63.
9. 9) S.K. Hyun, K. Murakami and H. Nakajima: J. JFS 74 (2002) 817–821.
10. 10) J.S. Park, K. Hyun, S. Suzuki and H. Nakajima: Acta Mater. 55 (2007) 5646–5654.10.1016/j.actamat.2007.06.022 ↗
11. 11) T. Shioya, Y. Matsuo, T. Hattori and H. Kawada: Fractography-Analysis and Case Studies, (Technosystem, Tokyo, 2010) pp. 115–116.
12. 12) M. Yokota and N. Tamura: Bull. Takaoka National College 12 (1998) 1–13.
13. 13) J. Yaokawa, D. Miura, K. Anzai, Y. Yamada and H. Yoshii: Mater. Trans. 48 (2007) 1034–1041.10.2320/matertrans.48.1034 ↗
14. 14) E. Koya and M. Nakagawa: J. JFS 89 (2017) 782–787.
15. 15) W. Huang, S.M. Opalka, D. Wang and T.B. Flanagan: Calphad 31 (2007) 315–329.10.1016/j.calphad.2007.02.002 ↗
16. 16) N. Kurita, N. Fukatsu and T. Ohashi: SHIGEN SOZAI, (1999) pp. 97–100.
17. 17) I. Ohnaka: Computer Dennetsu Gyoko-kaiseki-nyumon, (Maruzen, Tokyo, 1986) pp. 211–212.
18. 18) E. Niyama: Chuzo-dennetsu-kogaku, (Agne Gijutsu Center, Tokyo, 2001) pp. 97–98.