journal article·2019-11-01Open access

Controlling Factor for Maximum Tensile Stress and Elongation of Aluminum Alloy during Partial Solidification

Ryosuke Takai, Rei Hirohara, Naoki Endo, Yoshihiro Nagata, Toshimitsu Okane, Makoto Yoshida

MATERIALS TRANSACTIONS· Volume 60· Issue 11

Abstract

To predict hot tearing of direct chill casting ingot, both the tensile constitutive behavior and elongation of alloy are inevitable during partial solidification. For predicting both the maximum true stress σss and the elongation εelong regardless of alloy systems, their dominant factor was examined in terms of the solidification microstructure. For an Al–Mg and an Al–Cu alloys, (i) temperature T dependences of the maximum true stress and elongation (σss = f(T) and εelong = f(T)) and (ii) dihedral angle θ of liquid phase formed at grain boundary were measured experimentally. Then, fraction of solid cohesion C was determined by the Campbell’s model using the angle.
Source: openalex_inverted_index · Quality: baseline

Research context

OpenAlex topics: Aluminum Alloy Microstructure Properties · Aluminum Alloys Composites Properties · Solidification and crystal growth phenomena

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

Department of Modern Mechanical Engineering, Waseda University

Department of Modern Mechanical Engineering, Graduate School of Creative Science and Engineering, Waseda University

National Institute of Advanced Industrial Science and Technology

Kagami Memorial Research Institute for Materials Science and Technology, Waseda University

References (49)

Show source-provided references
1. 1) M. Morishita, M. Abe, K. Tokuda and M. Yoshida: J. JILM 59 (2009) 417–423.10.2464/jilm.59.417 ↗
2. 2) R. Takai, M. Otaki and M. Yoshida: J. JILM 68 (2018) 23–32.10.2464/jilm.68.23 ↗
3. 3) R. Takai, M. Otaki and M. Yoshida: J. JILM 68 (2018) 79–90.10.2464/jilm.68.79 ↗
4. 4) R. Takai and M. Yoshida: J. JFS 87 (2015) 582–588.
5. 5) B. Magnin, L. Maenner, L. Katgerman and S. Engler: Mater. Sci. Forum 217–222 (1996) 1209–1214.10.4028/www.scientific.net/MSF.217-222.1209 ↗
6. 6) H. Nagaumi and T. Umeda: J. Light Met. 2 (2002) 161–167.10.1016/S1471-5317(02)00042-1 ↗
7. 7) M. M’Hamdi, A. Mo and C.L. Martin: Metall. Mater. Trans. A 33 (2002) 2081–2093.10.1007/s11661-002-0040-6 ↗
8. 8) T. Subroto, A. Miroux, D. Mortensen, M. M’Hamdi, D.G. Eskin and L. Katgerman: IOP Conf. Series Mater. Sci. Eng. 33 (2012) 012068.10.1088/1757-899X/33/1/012068 ↗
9. 9) N. Jamaly, A.B. Phillion and J.-M. Drezet: Metall. Mater. Trans. B 44 (2013) 1287–1295.10.1007/s11663-013-9902-0 ↗
10. 10) R. Takai, T. Tsunoda, Y. Kawada, R. Hirohara and M. Yoshida: Mater. Trans. 59 (2018) 1333–1340.10.2320/matertrans.F-M2018824 ↗
11. 11) R. Takai, N. Endo, R. Hirohara, T. Tsunoda and M. Yoshida: Int. J. Adv. Manuf. Technol. 100 (2019) 1867–1880.10.1007/s00170-018-2791-2 ↗
12. 12) D.G. Eskin, Suyitno and L. Katgerman: Prog. Mater. Sci. 49 (2004) 629–711.10.1016/S0079-6425(03)00037-9 ↗
13. 13) M.G. Chu and D.A. Granger: Mater. Sci. Forum 217–222 (1996) 1505–1510.10.4028/www.scientific.net/MSF.217-222.1505 ↗
14. 14) M.G. Chu and A. Giron: Proceedings of the Merton C. Flemings Symposium on Solidification and Materials Processing, eds. by R. Abbaschian et al., TMS, (2001) pp. 223–228.
15. 15) O. Ludwig, J.-M. Drezet, C.L. Martin and M. Suéry: Metall. Mater. Trans. A 36 (2005) 1525–1535.10.1007/s11661-005-0244-7 ↗
16. 16) O. Ludwig, J.-M. Drezet, P. Ménésès, C.L. Martin and M. Suéry: Mater. Sci. Eng. A 413–414 (2005) 174–179.10.1016/j.msea.2005.09.087 ↗
17. 17) A.B. Phillion, S. Thompson, S.L. Cockcroft and M.A. Wells: Mater. Sci. Eng. A 497 (2008) 388–394.10.1016/j.msea.2008.07.027 ↗
18. 18) T. Subtoro: Ph.D. Thesis, TU Delft, (2010).
19. 19) J.-M. Drezet and G. Eggeler: Scr. Metall. Mater. 31 (1994) 757–762.10.1016/0956-716X(94)90223-2 ↗
20. 20) W.M. van Haaften, W.H. Kool and L. Katgerman: Mater. Sci. Eng. A 336 (2002) 1–6.
21. 21) F.H. Norton: The Creep of Steel at High Temperatures, (McGraw-Hill Book Co., 1929) p. 67.
22. 22) R.W. Bailey: Proc. Inst. Mech. Eng. 131 (1935) 131–349.10.1243/PIME_PROC_1935_131_012_02 ↗
23. 23) E. Giraud, M. Suéry and M. Coret: Metall. Mater. Trans. A 41 (2010) 2257–2268.10.1007/s11661-010-0268-5 ↗
24. 24) Q.L. Bai, H.X. Li, Q. Du, J.S. Zhang and L.Z. Zhuang: Int. J. Miner. Metall. Mater. 23 (2016) 949–958.10.1007/s12613-016-1311-3 ↗
25. 25) J. Campbell: Metallography 4 (1971) 269–278.10.1016/0026-0800(71)90018-8 ↗
26. 26) P.J. Wray: Acta Metall. 24 (1976) 125–135.10.1016/0001-6160(76)90015-8 ↗
27. 27) W.R. Apblett and W.S. Pellini: Weld. J. 33 (1954) 83–90.
28. 28) J.C. Borland: Br. Weld. J. 7 (1960) 508–512.
29. 29) J.A. Williams and A.R.E. Singer: J. Inst. Met. 96 (1968) 5–12.
30. 30) H. Chiba, T. Ueki, T. Toriyama, I. Endo, T. Kobayashi and M. Yoshida: J. JILM 61 (2011) 135–141.10.2464/jilm.61.135 ↗
31. 31) K. Shinji, H. Takahashi, Y. Motoyama and M. Yoshida: J. JILM 63 (2013) 253–259.10.2464/jilm.63.253 ↗
32. 32) R. Takai, A. Matsushita, S. Yanagida, K. Nakamura and M. Yoshida: Mater. Trans. 56 (2015) 1233–1241.10.2320/matertrans.L-M2015815 ↗
33. 33) R. Takai, S. Kimura, R. Kashiuchi, H. Kotaki and M. Yoshida: Mater. Sci. Eng. A 667 (2016) 417–425.10.1016/j.msea.2016.05.023 ↗
34. 34) A. Matsushita, R. Takai, H. Ezaki, T. Okane and M. Yoshida: Metall. Mater. Trans. A 48 (2017) 1701–1707.10.1007/s11661-017-3998-9 ↗
35. 35) R. Hirohara, Y. Kawada, R. Takai, M. Otaki, T. Okane and M. Yoshida: Mater. Trans. 58 (2017) 1299–1307.10.2320/matertrans.L-M2017823 ↗
36. 36) M. Easton, C. Davidson and D. St John: Metall. Mater. Trans. A 41 (2010) 1528–1538.10.1007/s11661-010-0183-9 ↗
37. 37) O.K. Riegger and L.H. Van Vlack: Trans. Metall. Soc. AIME 218 (1960) 933–935.
38. 38) K. Nakata and F. Matsuda: Trans. JWRI 24 (1995) 83–94.
39. 39) G.H. Gulliver: J. Inst. Met. 9 (1913) 120–157.
40. 40) E. Scheil: Z. Metallk. 34 (1942) 70–72.
41. 41) T.W. Clyne and W. Kurz: Metall. Trans. A 12 (1981) 965–971.10.1007/BF02643477 ↗
42. 42) T. Sato, S. Kitaoka and A. Kamio: J. JILM 38 (1988) 558–578.10.2464/jilm.38.558 ↗
43. 43) H. Yoshida and T. Fukui: J. JILM 38 (1988) 496–512.10.2464/jilm.38.496 ↗
44. 44) S. Fujikawa and K. Hirano: Mater. Sci. Eng. 27 (1977) 25–33.10.1016/0025-5416(77)90190-2 ↗
45. 45) H. Nagaumi, P. Suvanchai, T. Okane and T. Umeda: Mater. Trans. 47 (2006) 2918–2924.10.2320/matertrans.47.2918 ↗
46. 46) S. Hier-Majumder, P.H. Leo and D.L. Kohlstedt: Acta Mater. 52 (2004) 3425–3433.10.1016/j.actamat.2004.03.040 ↗
47. 47) S. Mihanyar, A. Mo, M. M’Hamdi and K. Ellingsen: Metall. Mater. Trans. A 42 (2011) 1887–1895.10.1007/s11661-010-0581-z ↗
48. 48) N. Sakaguchi: J. JILM 65 (2015) 492–497.10.2464/jilm.65.492 ↗
49. 49) N. Sakaguchi: J. JILM 67 (2017) 101–108.10.2464/jilm.67.101 ↗