Process Parameter Optimization for Particles Reinforced Weld-Bonding Joints of DP780 Dual-Phase Steel
Source abstract
Abstract
Alumina particles were added in the adhesive layer to stabilize the welding process and enhance the load capacity for weld-bonding joints. In this study, the strength of alumina particles reinforced weld-bonding joints of DP780 dual-phase steel sheets was investigated by conducting experiments based on the Box–Behnken Design (BBD). The multivariate regression models between process parameters (welding current, welding time and electrode pressure) and response values (failure load, nugget diameter) were established, and the optimal combination of weld-bonding process parameters was obtained. The findings indicate that welding current has the biggest impact on the strength of joints. The optimum process parameters ranges are: welding current of 8.5 kA, welding time of 125 ms, and electrode pressure of 0.5 MPa. Developed regression models were validated by experiments.
Source: openalex_inverted_index · Quality: baseline
Research context
OpenAlex topics: Advanced Welding Techniques Analysis · Welding Techniques and Residual Stresses · Mechanical Behavior of Composites
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
Affiliations
Faculty of Mechanical and Electrical Engineering, Kunming University of Science and Technology
Kunming Metallurgy College
References (17)
Show source-provided references
1. 1) Q.L. Cui, D. Parkes, D. Westerbaan, S.S. Nayak, Y. Zhou, D.C. Saha, D. Liu, F. Goodwin, S. Bhole and D.L. Chen: J. Mater. Eng. Perform. 26 (2017) 783–791. doi:10.1007/s11665-016-2454-010.1007/s11665-016-2454-0 ↗
2. 2) M. Sabzi, S.M. Far and S.M. Dezfuli: Int. J. Mater. Prod. Technol. 59 (2019) 3–15.10.1504/IJMPT.2019.10021817 ↗
3. 3) X.C. He: Int. J. Adhes. Adhes. 48 (2014) 59–66. doi:10.1016/j.ijadhadh.2013.09.01710.1016/j.ijadhadh.2013.09.017 ↗
4. 4) A. Kumar, G. Sharma and D.K. Dwivedi: Int. J. Adhes. Adhes. 84 (2018) 350–359. doi:10.1016/j.ijadhadh.2018.04.01210.1016/j.ijadhadh.2018.04.012 ↗
5. 5) X.Y. Sun, K. Zeng, X.C. He and L. Zhang: Nondestruct. Test. Eval. 32 (2017) 242–254. doi:10.1080/10589759.2016.124125110.1080/10589759.2016.1241251 ↗
6. 6) A.M. Pereira, J.A.M. Ferreira, F.V. Antunes and P.J. Bártoloet: J. Adhes. Sci. Technol. 28 (2014) 1432–1450. doi:10.1080/01694243.2012.69810710.1080/01694243.2012.698107 ↗
7. 7) A.C. Cadore-Rodrigues, C. Prochnow, T.A.L. Burgo, J.S. Oliveira, S.L. Jahn, E.L. Foletto, M.P. Rippe, G.K.R. Pereira and L.F. Valandro: J. Adhes. Dent. 22 (2020) 149–159. doi:10.3290/j.jad.a44151
8. 8) A. Drah, T. Kovačević, J. Rusmirović, N. Tomić, S. Brzić, M. Bogosavljavić and A. Marinković: J. Compos. Mater. 53 (2019) 2727–2742. doi:10.1177/002199831983913310.1177/0021998319839133 ↗
9. 9) Y.S. Zhao, Y.H. He, K.R. Yang, X.P. Wang, J.H. Bai and B. Du: High Volt. 5 (2020) 472–481. doi:10.1049/hve.2019.010810.1049/hve.2019.0108 ↗
10. 10) M.F. Khan, G. Sharma and D.K. Dwivedi: Int. J. Adv. Manuf. Technol. 78 (2015) 863–873. doi:10.1007/s00170-014-6670-110.1007/s00170-014-6670-1 ↗
11. 11) N. Muhammad, Y.H.P. Manurung, R. Jaafar, S.K. Abas, G. Tham and E. Haruman: J. Intell. Manuf. 24 (2013) 1175–1183. doi:10.1007/s10845-012-0648-310.1007/s10845-012-0648-3 ↗
12. 12) Ľ. Kaščák, E. Spišák and I. Gajdoš: Key Eng. Mater. 635 (2014) 143–146. doi:10.4028/www.scientific.net/KEM.635.14310.4028/www.scientific.net/KEM.635.143 ↗
13. 13) M.F. Li, Y.J. Wang, Z. Niu and S.L. Yang: Automot. Innov. 3 (2020) 221–230. doi:10.1007/s42154-020-00106-010.1007/s42154-020-00106-0 ↗
14. 14) J.Q. Yi, K. Zeng, X.C. He, B.Y. Xing and Y.Y. Feng: Mater. Trans. 61 (2020) 700–707. doi:10.2320/matertrans.MT-M201929510.2320/matertrans.MT-M2019295 ↗
15. 15) M.D.F. Khan, D.K. Dwivedi and S. Sharma: Mater. Des. 34 (2012) 673–678. doi:10.1016/j.matdes.2011.05.02510.1016/j.matdes.2011.05.025 ↗
16. 16) L. Boriwal, R.M. Sarviya and M.M. Mahapatra: J. Adhes. Sci. Technol. 31 (2017) 1591–1616. doi:10.1080/01694243.2016.126684410.1080/01694243.2016.1266844 ↗
17. 17) L.M. Liu and D.X. Ren: Mater. Des. 32 (2011) 3730–3735. doi:10.1016/j.matdes.2011.03.05010.1016/j.matdes.2011.03.050 ↗