journal article·2020-06

Impact of tool profile on mechanical behavior and material flow in friction stir welding of dissimilar aluminum alloys

O.P. Abolusoro, E.T. Akinlabi, S.V. Kailas

Publisher page

Abstract

Abstract The tool pin geometry used in friction stir welding of any material affects the transportation and mixing of the materials at the joint interface during the welding process. This further affects the mechanical properties of the joint. Tapered threaded and unthreaded tool pin profiles were investigated in this research work. The relationship between the material mixing characteristics and mechanical properties of each pin profile were evaluated. The results indicate that more materials mixing occurred in the nugget zone of the welds at lower rotational speed with the threaded tool pin than the unthreaded tool pin. However, at medium rotational speed, more volume of materials was swept into each other better in the unthreaded tool pin than the threaded pin. The tensile strengths of welds with the threaded tool pin were higher than the unthreaded tool pin. Although the two tool pins exhibit similarities in hardness variations across the weld zones however, higher average values of hardness were obtained at the nugget zone for welds performed with the tapered threaded tool pin. These could be as a result of better material mixing and higher opposition to grain dislocations across the dividing lines in the welds from the threaded tool pin.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Advanced Welding Techniques Analysis · Aluminum Alloys Composites Properties · Electronic Packaging and Soldering Technologies

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

Department of Mechanical Engineering Science University of Johannesburg JOHANNESBURG, REPUBLIC OF SOUTH AFRICA

Department of Mechanical Engineering Indian Institute of Science BANGALORE, REPUBLIC OF INDIA

References (26)

Show source-provided references
1. 10.1016/j.jmapro.2017.03.00510.1016/j.jmapro.2017.03.005 ↗
2. Hussain M.A. · Mater. Today Proc. · 2018 · 2 · 5
3. Abolusoro O.P. · Int. J. Mech. Prod. Eng. Res. Dev. · 2019 · 9 · 967
4. Singh R.K.R. · Mater. Des. · 2011
5. Ravikumar S. · Int. J. Adv. Mech. Eng. · 2014 · 4 · 101
6. Kumar R.A. · Adv. Mater. Res. · 2014 · 586 · 984
7. Nandan R. · Prog. Mater. Sci. · 2008
8. Gratecap F. · Int. J. Mater. Form. · 2008
9. Kumar K. · Mater. Sci. Eng. A. · 2008
10. 10.1016/j.matpr.2018.10.24810.1016/j.matpr.2018.10.248 ↗
11. 10.1080/1042691070186072310.1080/10426910701860723 ↗
12. 10.1016/j.mspro.2015.11.01310.1016/j.mspro.2015.11.013 ↗
13. Marzbanrad J. · Metall. Mater. Trans. B Process Metall. Mater. Process. Sci. · 2014
14. 10.1016/j.matdes.2012.03.02710.1016/j.matdes.2012.03.027 ↗
15. 10.1080/10426914.2010.53252710.1080/10426914.2010.532527 ↗
16. Mehta K.P. · Trans. Nonferrous Met. Soc. China. · 2017 · 27
17. 10.1016/j.engfailanal.2018.12.00310.1016/j.engfailanal.2018.12.003 ↗
18. Akinlabi E.T. · J. Mater. Eng. Perform. · 2012
19. 10.1007/s00170-016-8882-z10.1007/s00170-016-8882-z ↗
20. 10.1016/j.ijmachtools.2017.09.00210.1016/j.ijmachtools.2017.09.002 ↗
21. 10.1016/j.dt.2015.01.00410.1016/j.dt.2015.01.004 ↗
22. Colligan K. · Weld. J. · 1999 · 229
23. 10.1179/1879139512Y.000000001510.1179/1879139512Y.0000000015 ↗
24. J.A. Querin H.A. Rubisoff J.A. Schneider inASM Proc. Int. Conf. Trends Weld. Res. 2009 108.
25. Abolusoro O.P. · J. Phys.: Conf. Ser. · 2019 · 1378
26. 10.1051/mfreview/201902610.1051/mfreview/2019026 ↗