Electrosintering of iron powder compacts
Source abstract
Abstract
The influence of a nominal external electric field E=3 to 10 kV/cm on the sintering of iron powder compacts for 30 minutes at 1140 °C in a vacuum of ∼10−6 torr was investigated. It was found that the field reduced the porosity by as much as 29 to 73 pct compared to sintering without a field, the magnitude depending on the procedure employed to measure the density of the specimen. Optical microscopy revealed that the specimen electrosintered with E=10 kV/cm had a skin of ∼0.2 mm in thickness, where the porosity was significantly less than in the interior. This was also the depth of carburization that was obtained upon carburizing the electrosintered specimens. It is proposed that the decrease in porosity produced by the field results from a decrease in the chemical potential of vacancies at or just below the charged external surface. Vacancy flux equations employed to calculate the porosity as a function of distance below the external surface showed that the porosity becomes approximately zero at a distance of x c=0.4 to 0.5 mm below the surface, which is in reasonable accord with the microscopy measurements. Similar values of x c were obtained by assuming that the entire porosity decrease given by the density measurements occurred in a ring of thickness of x c below the external surface. The difference in the density measured by two Archimedes-principle procedures and microscopy observations suggests that the cavities open to the external surface of the electrosintered specimens are smaller or narrower than those for specimens sintered without a field.
Source: expertdata · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Electromagnetic Effects on Materials · Electrodeposition and Electroless Coatings
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (20)
Show source-provided references
1. H. Conrad, W. Cao, X.P. Lu, and A.F. Sprecher: Scripta Metall., 1989, vol. 23, pp. 697–702.10.1016/0036-9748(89)90514-0 ↗
2. W. Cao, X.P. Lu, A.F. Sprecher, and H. Conrad: in Superplasticity in Aerospace II, T. McNelley and H. Heikkenen, eds., TMS, Warrendale, PA, 1990, pp. 269–83.
3. H. Conrad, W. Cao, X.P. Lu, and A.F. Sprecher: Mater. Sci. Eng., 1991, vol. A138, pp. 247–58.10.1016/0921-5093(91)90694-I ↗
4. H. Conrad: “Effects of an External Electric Field during Sintering on the Porosity in Iron Powder Rods,” Progress Report, North Carolina State University, Raleigh, NC, Feb. 2, 1995.
5. H. Conrad and Z. Guo: “Effect of an Electric Field during Sintering on the Porosity in Iron Powder Rods,” Progress Report, North Carolina State University, Raleigh, NC, April 21, 1995.
6. F.V. Lenel: Powder Metallurgy, Metal Powder Industries Federation, Princeton, NJ, 1980.
7. R.M. German: Sintering Theory and Practice, John Wiley, New York, NY, 1996.
8. G.C. Kuczynski: Trans. AIME, 1949, vol. 185, pp. 169–78.
9. D.L. Johnston: J. Appl. Phys., 1969, vol. 40, pp. 192–200.10.1063/1.1657030 ↗
10. V.A. Ivensen: Densification of Metal Powders during Sintering, Consultant Bureau, New York, NY, 1973.10.1007/978-1-4757-0106-7 ↗
11. P. Shewmon: Diffusion in Solids, 2nd ed., TMS, Warrendale, PA, 1989.
12. CRC Handbook, The Chemical Rubber Co., Cleveland, OH, 1978.
13. T. Hare: North Carolina State University, Raleigh, NC, private communication, 1996.
14. C.M. Stansbury: Master’s Thesis, University of Kentucky, Lexington, KY, 1975.
15. D. Newman: Mater. Sci. Eng., 2000, vol. A287, pp. 198–204.10.1016/S0921-5093(00)00776-0 ↗
16. R.A. Johnson: Diffusion in Bcc Metals, ASM, Metals Park, OH, 1965, p. 357.
17. A.D. LeClair: J. Nucl. Mater., 1978, vols. 69–70, pp. 198–204.
18. Y.H. Kim, J. Kang, J. Kim, W. Kim, and Y. Kwon: Proc. NEDO Int. Symp. Functionally Graded Materials, Tokyo, Oct. 21–22, Paris Publ., Tokyo, 1999, pp. 123–26.
19. S.H. Risbud, J.R. Groza, and M.J. Kim: Phil. Mag., 1994, vol. 69B, pp. 523–33.
20. T. Okabe and A. Guy: Metall. Trans., 1970, vol. 1, pp. 2705–13.10.1007/BF03037805 ↗