journal article·2024-04-11Open access

The Effect of a Coating Sprayed Using Supersonic Flame Coating Technology on the Mechanical Properties and Interface Structure of a Thick Steel/Aluminum Composite Plate during Hot Rolling

Meng Yan, Meng-Ye Wang, Zi-Yi Cui, Jiu-Ba Xu, Hua-Gui Huang

Metals· Volume 14· Issue 4

Abstract

Given the characteristics of a thick steel/aluminum composite plate, such as its large thickness and the significant differences between its components, it is difficult to prepare using direct rolling. Instead, a thick steel/coating/aluminum composite plate may be successfully prepared by combining supersonic flame coating technology with a hot rolling composite process. In this study, the interface shear strength test, SEM, EDS, and other detection methods were applied to investigate the effects of the reduction rate and coating thickness on the interface structure and mechanical properties. The results show that under the condition of single-pass direct rolling, the micro-interface of steel/aluminum is improved with an increase in the reduction rate, but the bonding strength of the interface remains poor. After adding the coating, the thickness of the diffusion layer and the shear strength increase significantly. When the coating thickness is reduced to 0.1 mm, the deformation coordination and shear strength of the composite plate are further enhanced under the combined action of mechanical interlocking and metallurgical bonding. The tensile shear fracture is mainly located at the steel/coating interface. The interfacial shear strength reaches 66 MPa, which exceeds the requirements of the US military standard MIL-J-24445A (SH) for steel/aluminum shear strength. The research results thus support the use of this new method for the simple and efficient production of thick steel/aluminum composite plates.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Surface Treatment and Residual Stress · Metal Alloys Wear and Properties · High-Velocity Impact and Material Behavior

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

School of Mechanical Engineering, Yanshan University, Qinhuangdao 066004, China

Hebei Innovation Center for Equipment Lightweight Design and Manufacturing, Yanshan University, Qinhuangdao 066004, China

National Engineering Research Center for Equipment and Technology of Cold Rolled Strip, Yanshan University, Qinhuangdao 066004, China

Funding

National Natural Science Foundation of China Youth Fund · Science and Technology Project of Hebei Education Departmen · Natural Science Foundation of Hebei Province Youth Science Fund Project · Central guidance for local scientific and technological development funding projects

References (37)

Show source-provided references
1. Laminated Steel/Aluminum Composites: Improvement of Mechanical Properties by Annealing Treatment10.1016/j.mtcomm.2021.102866 ↗
2. Effect of cumulative deformation and interlayer mechanical properties on bonding strength of corrugated interface steel/aluminum composite plate10.1016/j.jmapro.2023.08.028 ↗
3. Fabrication of aluminum/stainless steel bimetallic composites through a combination of additive manufacturing and vacuum-assisted melt infiltration casting10.1016/j.jmapro.2021.07.047 ↗
4. Fatigue strength of new explosively welded steel-aluminum transition joint used in ships10.1016/j.oceaneng.2023.115990 ↗
5. Kaya, Y. (2018). Microstructural, Mechanical and Corrosion Investigations of Ship Steel-Aluminum Bimetal Composites Produced by Explosive Welding. Metals, 8.10.3390/met8070544 ↗
6. Unbalanced thermal field assisted thermo-compensated resistance brazing welding 6061 aluminum alloy to 304 stainless steel10.1016/j.jmrt.2023.03.071 ↗
7. Microstructure evolution and fracture behavior of rotating laser welded-brazed 6061 aluminum alloys/304 SS dissimilar joint10.1016/j.matchar.2022.112543 ↗
8. Experimental and numerical investigations on the microstructural features and mechanical properties of explosively welded aluminum/titanium/steel trimetallic plate10.1016/j.matchar.2024.113669 ↗
9. Research on microstructure and mechanical properties of laser keyhole welding-brazing of automotive galvanized steel to aluminum alloy10.1016/j.matdes.2012.09.023 ↗
10. An investigation on rivet plug laser welding of hybrid joints between high-strength steel and aluminum alloy10.1016/j.optlastec.2023.109470 ↗
11. Diffusion brazing of aluminium by PVD applied filler metals10.1002/mawe.200800339 ↗
12. Interface characterization and tensile performance of deep-penetration welding-brazing of thick aluminium/steel butt joints10.1016/j.matchar.2022.111811 ↗
13. Towards enhanced mechanical performance of Al/steel welded-brazed joints via laser surface texturing modification10.1016/j.jmrt.2023.11.029 ↗
14. Explosive Welding of Metal Plates10.1016/j.jmatprotec.2007.09.028 ↗
15. Chen, Y., Gao, Y., Guo, C., Guo, Y., Guo, Z., Liu, Y., and Liu, T. (2023). Effect of the Addition of Steel Fibers on the Bonding Interface and Tensile Properties of Explosion-Welded 2A12 Aluminum Alloy and SS-304 Steel. Materials, 16.10.3390/ma16010116 ↗
16. Joining of Advanced High-Strength Steel to AA 6061 Alloy by Using Fe/Al Structural Transition Joint10.1016/j.matdes.2014.12.028 ↗
17. Bonding Process and Interfacial Reaction in Horizontal Twin-Roll Casting of Steel/Aluminum Clad Sheet10.1016/j.jmatprotec.2017.03.003 ↗
18. Study on the effects of initial temperature and thickness ratio of component metals on the preparation of aluminum/steel clad plates by the new different temperature rolling method10.1016/j.jmapro.2023.04.004 ↗
19. A study of joint quality of aluminum and low carbon steel strips by warm rolling10.1016/j.matdes.2008.06.042 ↗
20. Experimental research on the technology of two-pass different temperature rolling for thick steel/aluminum/aluminum-alloy composite plate10.1007/s00170-022-09120-4 ↗
21. Influence of plasma spraying on interfacial microstructure and mechanical property of thick steel/aluminum laminated plate by hot rolling
22. Experimental investigation of laser beam welding of explosion-welded steel/aluminum structural transition joints10.1016/j.matdes.2009.10.032 ↗
23. Interfacial bonding mechanism of Cu/Al composite plate produced by corrugated cold roll bonding10.1007/s12598-020-01660-6 ↗
24. Yu, C., Zhang, W., Jiang, R., Wu, Y., and Xiao, H. (2023). Preparation Method and Properties of Q235/5083 Composite Plate with 1060 Interlayer by Differential Temperature Rolling with Induction Heating. Metals, 13.10.3390/met13091501 ↗
25. Preparation of Steel/Aluminum Laminated Composites by Differential Temperature Rolling with Induction Heating
26. Effect of Cu Foil on Laser Butt Welding Quality of Aluminum/Steel Dissimilar Metals Joint10.3901/JME.2014.14.143 ↗
27. Structural steel-aluminum sandwich composites based on low-carbon steel 006/IF10.1007/s11041-013-9569-9 ↗
28. High Velocity Oxy-fuel Sprayed Coatings—A Review
29. Tribological Behavior of Carbon Nanotubes Reinforced High Velocity Oxy-Fuel Sprayed WC-20 wt.% Co Coatings10.1007/s11666-021-01230-x ↗
30. (1977). Joint, Bimetallic Bonded, Aluminum to Steel (Standard No. MIL-J-24445A).
31. Influence of hot rolling on microstructure and mechanical behaviour of Al6061-ZrB2 in-situ metal matrix composites10.1016/j.msea.2018.09.104 ↗
32. Microstructure, growth kinetics and mechanical properties of interface layer for roll bonded aluminum-steel clad sheet annealed under argon gas protection10.1016/j.vacuum.2018.02.018 ↗
33. First-principles and experimental investigations on ductility/brittleness of intermetallic compounds and joint properties in steel/aluminum laser welding10.1016/S1003-6326(21)65706-0 ↗
34. Bonding enhancement of cold rolling Al/steel composite plates via self-nano film modification10.1016/j.jmatprotec.2021.117427 ↗
35. Arbo, S.M., Bergh, T., Holmedal, B., Vullum, P.E., and Westermann, I. (2019). Relationship between Al-Ni intermetallic Phases and Bond Strength in Roll Bonded Steel-Aluminum Composites with Nickel Interlayers. Metals, 9.10.3390/met9080827 ↗
36. High temperature oxidation performance of Ni-Cr-Ti and Ni-5Al coatings10.1016/j.matpr.2019.11.048 ↗
37. Analysis on mechanism of steel plate pre-oxidation in improving bonding properties of cold-rolled 6061 Al/Q235 steel composite plate10.1016/j.jmatprotec.2023.117960 ↗