journal article·2025-02-09Open access

Microstructure and Mechanical Behaviors of Fiber-Laser-Welded QP980-QP1180 Steels

Hafize Çelik, Onur Saray

Metals· Volume 15· Issue 2

Abstract

Advanced high-strength steels are considered the first choice when manufacturing lighter vehicles. Quench-partitioning (QP) steels are good candidates that fulfill manufacturing and performance requirements with their outstanding strength and formability. Laser welding offers a productive solution to the challenges of liquid metal embrittlement due to a low heat input and higher welding efficiency. This study investigated the microstructural evolution and mechanical performance of dissimilar laser-welded joints between QP980 and QP1180 steels. The microstructure of the joint mainly consisted of martensite phase in the fusion zone (FZ) and super-critical heat-affected zone (HAZ). In the mid and sub-critical HAZ, the microstructure consisted of tempered martensite along with ferrite and retained austenite on both sides. Due to these microstructural evolutions, FZ and HAZ are strengthened, and thus, laser welds can be achieved without the formation of a visible soft zone. Fracture of the joints occurred in softer base metal (BM) with ductile characteristics without any considerable strength loss. However, the ductility of the joints was lower than that of BMs because of deformation localization due to microstructure, yield strength, and thickness variations in the tensile and Erichsen test specimens. These results show that laser welding can be considered an effective alternative for joining QP steels.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Microstructure and Mechanical Properties of Steels · Welding Techniques and Residual Stresses · Metal Alloys Wear and Properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

Department of Mechanical Engineering, Bursa Technical University, 16310 Bursa, Turkey

TOFAS R&D Center, Turkish Automobile Factory, 16110 Bursa, Turkey

References (35)

Show source-provided references
1. New Generation Advanced High Strength Steels: Developments, Trends and Constraints
2. European Commission and CRU (2021, June 01). European Commission and CRU. Available online: https://commission.europa.eu/index_en.
3. Stellantis (2024, July 18). Stellantis: Official Global Website. Available online: https://www.stellantis.com/en/company/dare-forward-2030/care.
4. Twin-spot laser welding of advanced high-strength multiphase microstructure steel10.1016/j.optlastec.2017.01.011 ↗
5. Fonstein, N. (2017). Dual-Phase Steels in Automotive Steels, Woodhead Publishing.
6. Butuc, M.C., Vincze, G., Santos, R., Pereira, A., Santos, A.D., Amaral, R.L., and Barlat, F. (2024). Formability of third generation advanced high strength steel: Experimental and theoretical approach. Int. J. Mech. Sci., 281.10.1016/j.ijmecsci.2024.109559 ↗
7. Bao Steel Company (2024, March 01). Baowu Open Innovation. Available online: http://rd.baosteel.com/zypt/en/ability/see/abilityDetailsBSSF5/1/318362afb3924a479c3bb4407ce48f6a.
8. World Auto Steel (2022, March 03). The Latest Global Formability Diagram. Available online: https://www.worldautosteel.org/ahss-insights-blog-the-new-global-formability-diagram.
9. New generation steels for light weight vehicle safety related applications10.1515/mt-2024-0052 ↗
10. A comprehensive overview of high strength and toughness steels for automobile based on QP process10.1016/j.jmrt.2023.09.210 ↗
11. Shome, M., and Tumuluru, M. (2015). Introduction to Welding and Joining of Advanced High-Strength Steels (AHSS) in Welding and Joining of Advanced High-Strength Steels (AHSS), Woodhead Publishing.10.1016/B978-0-85709-436-0.00001-1 ↗
12. Effect of welding current on microstructure and mechanical properties of 15% deformed TWIP steel joined with electrical resistance spot welding
13. Tuncel, O., Aydın, H., and Çetin, Ş. (2018, January 7–8). Nd: Yag lazer kaynağı ile birleştirilen DP600 çeliğinde darbe süresinin mikroyapı ve mekanik özelliklerine etkisi. Proceedings of the 9th International Automotive Technologies Congress, OTEKON, Bursa, Türkiye. Available online: https://www.otekon.org/dokuman/books/9thOtekonBook.pdf.
14. Microstructure and mechanical properties of laser welded dissimilar DP600/DP980 dual-phase steel joints10.1016/j.jallcom.2010.08.158 ↗
15. Welding behavior of an ultrahigh-strength quenching and partitioning steel by fusion and solid-state welding methods10.1016/j.jmrt.2022.01.086 ↗
16. Investigation of The Effect of The Laser Welding Parameters Change on Welding Seam for Stainless Steel
17. Numerical and experimental investigation of the effect of heat input on weld bead geometry and stresses in laser welding10.1515/mt-2024-0080 ↗
18. Microstructure Characterization and Mechanical Properties of Laser Welded Super High Strength QP980 Automotive Steel10.4028/p-7WU8lU ↗
19. Xue, J., Guo, W., Zhang, Y., Xia, M., Jia, Q., Chi, J., Shi, J., Wu, Y., and Zhang, H. (2022). Local microstructure and mechanical characteristics of HAZ and tensile behavior of laser welded QP980 joints. Mater. Sci. Eng., 854.10.1016/j.msea.2022.143862 ↗
20. Microstructure and mechanical properties of fiber laser welded QP980 steel10.1016/j.jmatprotec.2018.02.015 ↗
21. Effect of water-cooling assistance on fatigue behavior of laser welded QP980 steel10.1016/j.jmrt.2023.12.138 ↗
22. Zahrani, M.M., Ranjbarnodeh, E., Ketabchi, M., and Ghassemali, E. (2024). Microstructure evolution and mechanical properties of laser-welded joints of 1.2 GPa-class quenching and partitioning steel. Opt. Laser Technol., 170.10.1016/j.optlastec.2023.110257 ↗
23. Acceleration of regeneration treatment for nanostructured bainitic steel by rotary impacting trailed welding10.1016/j.jmatprotec.2014.06.024 ↗
24. Tensile properties, and work hardening behavior of laser-welded dual-phase steel joints10.1007/s11665-011-9865-8 ↗
25. Xue, J., Peng, P., Guo, W., Xia, M., Tan, C., Wan, Z., Zhang, H., and Li, Y. (2021). HAZ Characterization and Mechanical Properties of QP980-DP980 Laser Welded Joints. Chin. J. Mech. Eng. Ji Xie Gong Cheng Xue Bao, 34.10.1186/s10033-021-00596-x ↗
26. Huang, J., Li, S., Zhong, H., Xiao, S., and Li, D. (2022). Microstructure, Mechanical Properties, and Corrosion Behavior of Laser-Welded Dissimilar Joints Between DP980 and QP980 Steel. Steel Res. Int., 93.10.1002/srin.202100541 ↗
27. Investigation on microstructure and properties of dissimilar joint between TRIP800 and QP980 fabricated by laser welding10.1080/13621718.2020.1868700 ↗
28. Microstructure, and mechanical properties of laser welded dissimilar joints between QP, and boron alloyed martensitic steels10.1016/j.jmatprotec.2018.04.020 ↗
29. Microstructure, and mechanical properties of fiber laser welded QP980/press-hardened 22MnB5 steel joint10.1016/j.jmrt.2020.07.011 ↗
30. Microstructural evolution and deformation behavior of fiber laser welded QP980 steel joint10.1016/j.msea.2018.01.050 ↗
31. A critical review on dissimilar welds joints between martensitic and austenitic steel for power plant application10.1016/j.jmapro.2020.08.019 ↗
32. Xue, B., Li, Y., Yi, W., Shi, S., Dai, Y., Liu, C., Ren, M., and He, C. (2024). Biaxial Very High Cycle Fatigue Testing and Failure Mechanism of Welded Joints in Structural Steel Q345. Crystals, 14.10.3390/cryst14100850 ↗
33. Phase evolution in P92 and E911 weld metals during ageing10.1016/j.msea.2007.07.036 ↗
34. Formability of ultrafine-grained interstitial-free steels10.1007/s11661-013-1781-0 ↗
35. Santos, R.O., Pereira, A.B., Butuc, M.C., Vincze, G., Festas, A.J., and Moreira, L.P. (2019). Development of a device compatible with universal testing machine to perform hole expansion and Erichsen cupping tests. Machines, 8.10.3390/machines8010002 ↗