Edge Microstructure and Strength Gradient in Thermally Cut Ti-Alloyed Martensitic Steels
Source abstract
Abstract
Recently developed Ti-alloyed martensitic steels are believed to exhibit higher wear resistance than traditionally quenched and tempered medium carbon steels. However, their properties may deteriorate during thermal cutting and welding as a result of microstructure tempering. This would present significant challenges for the metal fabrication industries. A decrease in strength and wear resistance associated with tempering should vary with steel composition, initial steel microstructure and properties, and cutting method. In this work, we investigated the effect of thermal cutting on the edge microstructure and properties in two alloyed plate steels containing 0.27C-0.40Ti and 0.39C-0.60Ti (wt.%) commercially rolled to 12 mm thickness. Three cutting methods were applied to each of the two plates: oxy-fuel, plasma and water-jet. Microstructure characterisation was carried out using optical and scanning electron microscopy. With an increase in thermal effect, from water-jet to plasma to oxy-fuel, the heat affected zone width increased and hardness decreased in both steels. However, the hardness profile from the cut edge to the base metal significantly varied with steel composition, particularly C and Ti contents. The dependence of grain structure and precipitation kinetics on steel composition, and cutting method, were thoroughly investigated and linked to the hardness profile variation. The obtained results will be used to optimise the technological parameters for cutting and welding of Ti-alloyed martensitic steels.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: Microstructure and Mechanical Properties of Steels · Hydrogen embrittlement and corrosion behaviors in metals · Welding Techniques and Residual Stresses
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
Affiliations
ARC Research Hub for Australian Steel Manufacturing, University of Wollongong, Wollongong, NSW 2522, Australia
School of Mechanical, Materials, Mechatronic and Biomedical Engineering, University of Wollongong, Wollongong, NSW 2522, Australia
BlueScope Steel Limited, Five Islands Rd., Port Kembla, NSW 2505, Australia
Bisalloy Steels, 18 Resolution Drive, Unanderra, NSW 2526, Australia
Funding
Australian Research Council
References (62)
Show source-provided references
1. A study of the abrasive wear of carbon steels10.1016/0043-1648(91)90209-D ↗
2. The design of advanced performance high strength low-carbon martensitic armour steels: Microstructural considerations10.1016/j.msea.2007.07.078 ↗
3. Microstructural and fractographical studies on quenched and tempered armor steels
4. Effect of heat treatment on mechanical and ballistic properties of a high strength armour steel10.1016/j.ijimpeng.2009.09.003 ↗
5. Investigation into feasibility of FSW process for welding 1600 MPa quenched and tempered steel10.1016/j.msea.2015.11.054 ↗
6. Cold cracking in weldments of steel S 690 QT10.1007/BF03263411 ↗
7. Hydrogen induced cold cracking studies on armour grade high strength, quenched and tempered steel weldments10.1016/j.ijhydene.2008.01.035 ↗
8. Kuzmikova, L., Callaghan, M., Larkin, N., Scott, R., DeJong, R., Li, H., and Norrish, J. (2010, January 15–16). A study of a continuous cooling behaviour and effect of preheat and interpass temperature on the HAZ of high strength quenched and tempered steel. Proceedings of the International Institute of Welding Annual Assembly, Istanbul, Turkey. paper IX-2352-10.
9. Barenyi, I., Hires, O., and Liptak, P. (2011, January 26–28). Degradation of mechanical properties of armoured steels after its welding. Proceedings of the International Conference AFASES2011, Brasov, Romania.
10. Investigation into feasibility of hybrid laser-GMAW process for welding high strength quenched and tempered steel
11. Study of the sensitivity of high-strength cold-resistant shipbuilding steels to thermal cycle of arc welding10.1186/s40712-018-0090-1 ↗
12. Hydrogen-assisted cracking of GMA welded 960 MPa grade high-strength steels10.1016/j.ijhydene.2020.05.077 ↗
13. Tensile properties of shielded metal arc welded ultrahigh hard armour steel joints10.30574/wjaets.2020.1.2.0029 ↗
14. Design of low hardness abrasion resistant steels10.1016/j.wear.2013.01.002 ↗
15. Effects of composition and microstructure on the abrasive wear performance of quenched wear resistant steels10.1016/j.wear.2014.06.003 ↗
16. Microstructure and abrasive wear behavior of medium carbon low alloy martensitic abrasion resistant steel10.1016/S1006-706X(14)60015-7 ↗
17. Wear behavior and work hardening of high strength steels in high stress abrasion10.1016/j.wear.2014.10.018 ↗
18. Nanocrystallization and martensite formation in the surface layer of medium-manganese austenitic wear-resistant steel caused by shot peening10.1016/j.msea.2006.12.066 ↗
19. The influence of atmospheric humidity and grain size on the friction and wear of AISI 304 austenitic stainless steel10.1016/S0167-577X(03)00351-3 ↗
20. An investigation of the wear behaviour of 0.2% C dual phase steels10.1016/j.jmatprotec.2007.09.044 ↗
21. Zum Gahr, K.H. (1987). Microstructure and Wear of Materials, Elsevier.
22. Effect of carbon content on abrasive impact wear behavior of Cr-Si-Mn low alloy wear resistant cast steels10.3389/fmats.2019.00153 ↗
23. Effects of carbon and chromium additions on the wear resistance and surface roughness of cast high-speed steel rolls10.1007/s11661-001-0041-x ↗
24. Characterization of wear and metallurgical properties for development of agricultural grade steel suitable in specific soil conditions10.1016/j.wear.2006.12.006 ↗
25. Dry sliding friction and wear behaviour of hardened AISI D2 tool steel with different hardness levels10.1016/j.triboint.2013.05.006 ↗
26. Review on TiC reinforced steel composites10.1023/A:1017947206490 ↗
27. Effects of Ti addition and reheating quenching on grain refinement and mechanical properties in low carbon medium manganese martensitic steel10.1016/j.matdes.2011.08.015 ↗
28. Martensitic wear resistant steels alloyed with titanium10.1016/j.wear.2020.203203 ↗
29. Optimizing diamond growth for an atmospheric oxyacetylene torch10.1557/JMR.1997.0172 ↗
30. (2019, December 20). Cutting Processes—Application of Oxyfuel Cutting. Available online: https://www.twi-global.com/technical-knowledge/job-knowledge/cutting-processes-application-of-oxyfuel-cutting-050.
31. Eyres, D.J. (2007). Ship Construction, Butterworth-Heinemann.10.1016/B978-075068070-7/50017-7 ↗
32. (2019, December 20). Cutting Processes—Plasma Arc Cutting—Process and Equipment Considerations. Available online: https://www.twi-global.com/technical-knowledge/job-knowledge/cutting-processes-plasma-arc-cutting-process-and-equipment-considerations-051.
33. A comprehensive study on the microstructure and mechanical properties of arc girth welded joints of spiral welded high strength API X70 steel pipe10.1007/s43452-020-00018-0 ↗
34. Combined finite element and phase field method for simulation of austenite grain growth in the heat-affected zone of a martensitic steel weld
35. Microstructure model for the heat-affected zone of X80 linepipe steel10.1080/02670836.2016.1142705 ↗
36. Effect of titanium addition on behavior of medium carbon steel
37. On the chemistry and stability of complex carbides and nitrides in microalloyed steels10.1016/0001-6160(85)90129-4 ↗
38. High-speed steels with addition of niobium or titanium10.1016/S0924-0136(96)02678-7 ↗
39. Statistical and theoretical analysis of precipitates in dual-phase steels microalloyed with titanium and their effect on mechanical properties10.1016/S1359-6454(99)00190-1 ↗
40. Yu, W.T., Li, J., Shi, C.B., and Zhu, Q.T. (2016). Effect of titanium on the microstructure and mechanical properties of high-carbon martensitic stainless steel 8Cr13MoV. Metals, 6.10.3390/met6080193 ↗
41. Bhadeshia, H.K.D.H., and Honeycombe, S.R. (2006). Steels: Microstructure and Properties, Butterworth-Heinemann. [3rd ed.].10.1016/B978-075068084-4/50016-9 ↗
42. Tempering of lath martensite in low and medium carbon steels: Assessment and challenges10.1002/srin.201700038 ↗
43. Critical points of hypoeutectoid steel—Prediction of the pearlite dissolution finish temperature Ac1f
44. Modelling of CCT diagrams for engineering and constructional steels10.1016/j.jmatprotec.2007.04.099 ↗
45. Designing new corrosion resistant ferritic heat resistant steel based on optimal solid solution strengthening and minimisation of undesirable microstructural components10.1016/j.commatsci.2013.12.009 ↗
46. Effect of molybdenum on continuous cooling bainite transformation of low-carbon microalloyed steel10.1016/j.matdes.2005.02.006 ↗
47. Hu, H., Xu, G., Zhou, M., and Yuan, Q. (2016). Effect of Mo content on microstructure and property of low-carbon bainitic steels. Metals, 6.10.3390/met6080173 ↗
48. Clustering and precipitation processes in a ferritic titanium-molybdenum microalloyed steel10.1016/j.jallcom.2016.08.146 ↗
49. Precipitation and clustering in a Ti-Mo steel investigated using atom probe tomography and small-angle neutron scattering10.1016/j.msea.2018.01.070 ↗
50. Microstructural characterization and strengthening behavior of nanometer sized carbides in Ti–Mo microalloyed steels during continuous cooling process10.1016/j.matchar.2016.01.023 ↗
51. Kostryzhev, A.G., and Marenych, O.O. (2018). New technology to produce 1 GPa low carbon microalloyed steels from cast strip. Metals, 8.10.3390/met8090662 ↗
52. Development of Ti–V–Mo complex microalloyed hot-rolled 900MPa grade high strength steel10.1007/s40195-015-0243-7 ↗
53. Effect of molybdenum addition on the precipitation of carbides in the austenite matrix of titanium micro-alloyed steels10.1007/s10853-016-9804-z ↗
54. Study of the effect of thermal cutting on the microstructure and chemical composition of the edges of workpieces made of steel brands S345, S39010.1016/j.proeng.2016.07.171 ↗
55. Effect study of thermal cutting methods on the edge’s microstructure of high-strength steel grade S700MC10.4028/www.scientific.net/MSF.946.928 ↗
56. Analysis of heat affected zone in plasma arc cutting of SS 316L plates
57. Coarsening of TiC in austenitic stainless steel–Experiments and simulations in comparison10.1016/S0921-5093(00)00827-3 ↗
58. Growth and dissolution of NbC particles in an austenitic stainless steel10.1016/0026-0800(77)90024-6 ↗
59. Dissolution and precipitation behaviour in steels microalloyed with niobium during thermomechanical processing10.1016/j.actamat.2015.06.057 ↗
60. Particle coarsening in binary and multicomponent alloys10.1016/0956-716X(94)90413-8 ↗
61. Papaefthymiou, S., Bouzouni, M., and Gavalas, E. (2018). Theoretical study of particle dissolution during homogenization in Cu–Fe–P alloy. Metals, 8.10.3390/met8060455 ↗
62. Effect of TiC and NbC carbides on creep life of stainless steels10.1080/09603409.2018.1452365 ↗