Design and performance analysis of uniform meander structured RF MEMS capacitive shunt switch along with perforations
Source abstract
Abstract
This paper presents design and simulation of uniform structured RF MEMS capacitive shunt switch using FEM tool and HFSS software. The switches with different shaped meanders and perforations which result in less spring constant, less pull-in voltage, high isolation loss, high switching speed and low insertion loss have been designed. From the simulated results it is observed that the rectangular perforations gives the better results, when compared with square and cylindrical shaped perforations. Comparative study is done for zigzag, plus and three square shaped meander along with rectangular perforations on each structure. When the gap between the dielectric and the movable beam is 0.8 µm, the up state capacitance for HfO2 is 4.06fF and for Si3N4 is 3.80fF. The downstate capacitance for HfO2, Si3N4 is 49fF, 26.9fF respectively. The capacitance ratio is 120.6. Poly-tetra-fluoro-ethylene material is given for the movable beam whose young’s modulus is 0.4 GPa and the spring constant is calculated theoretically for each structure; by using this the pull in voltage and the settling time are calculated. Step switch with three square Meander has switching time 10.25 µs, pull in voltage as 2.45 V. By using HFSS 3-D electromagnetic model we observed the return loss (S11) is less than −60 dB, the insertion loss is less than −0.07 dB in the range of 1–40 GHz frequency and switch isolation (S21) is −61 dB at 28 GHz frequency.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Advanced MEMS and NEMS Technologies · Acoustic Wave Resonator Technologies · Mechanical and Optical Resonators
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (16)
Show source-provided references
1. Angira M, Rangra K (2014) Design and investigation of a low insertion loss, broadband, enhanced self and hold down Power RF-MEMS switch. Microsyst Technol 21(6):1173–1178. doi: 10.1007/s00542-014-2188-610.1007/s00542-014-2188-6 ↗
2. Angira M, Sundaram GM, Rangra K, Bansal D, Kaur M (2013), On the investigation of an interdigitated, high capacitance Ratio shunt RF-MEMS switch for X-band applications. In: Proceedings of NSTI nanotechnology, Washington 2, pp 189–192
3. Bachman M, Yang Z, Minfeng W, Li G (2012) High-power magnetically actuated microswitches fabricated in laminates. IEEE Electron Device Lett 33(9):1309–1311. doi: 10.1109/LED.2012.220655310.1109/LED.2012.2206553 ↗
4. Balaraman D, Bhattacharya SK, Ayazi F, Papapolymerou J (2012) Low-cost low actuation voltage copper RF MEMS switches. IEEE Microw Theory Tech Symp 2:1225–1228
5. Fedder GK (1994) Simulation of micro-electro-mechanical systems. Ph.D. dissertation, Electrical Engineering and Computer Science, University of California at Berkeley, USA
6. Guha K, Kumar M, Parmar A, Baishya S (2016) Performance analysis of RF MEMS capacitive switch with non-uniform meandering technique. Microsystem Technologies, vol 22. Springer Berlin Heidelberg, pp 2633–264010.1007/s00542-015-2545-0 ↗
7. He X, Lv Z, Liu B, Li Z (2011) Electro thermally actuated RF MEMS capacitive switch with automatic layer deposited (ALD) dielectrics. (Solid-state Sensors, Actuator sand Microsystems Conference, (TRANSDUCERS)10.1109/TRANSDUCERS.2011.5969695 ↗
8. Lee J, Yang WS, Kang S, Choi CA (2004) Design and parameter-extraction based small-signal modelling of a novel center-anchor MEMS series switch. In: Proceedings of the 34th European microwave conference, Amsterdam, The Netherlands, pp 1433–1436
9. Manfaineiad Y, Zarghami M, Kouzani AZ (2013) Design and simulation of high isolation RF MEMS shunt Capacitor switch for C-K band. Electrical Engineering (ICEE), 21st Iranian conference, Mashhad, pp 1–5
10. Molaei S, Ganji BA (2016) Design and simulation of a novel RF MEMS shunt capacitive switch with low actuation voltage and high isolation. Springer-Verlag, Berlin Heidelberg
11. Patil GD, Kolhare NR (2013) A review paper on RF MEMS switch for wireless communication. Int J Eng Trends Technol 4(2):195–198
12. Ramli N, Sidek O (2012) Reducing an actuation voltage of RF MEMS capacitive switch through three electrodes topology using architect coventorware. J Eng Technol 2(2):46–51. ISSN 2231-8798
13. Rebeiz GM (2003) RF MEMS: theory, design and technology, 3rd edn. Wiley, New Jersey10.1002/0471225282 ↗
14. Sharma A, Shah A, Bharti R (2015) Design and simulation of low actuation voltage perforated shunt RF MEMS switch. Int J Eng Tech Res 3(6). ISSN 2321-0869
15. Shekhar S, Vinoy KJ, Ananthasuresh GK (2014) Design and characterization of capacitive RF MEMS switches with low pull-in voltage. Microwave and RF conference (IMaRC), IEEE International, pp 182–18510.1109/IMaRC.2014.7038983 ↗
16. Verma P, Singh S (2013) Design and simulation of RF MEMS capacitive type shunt switch & its major applications. IOSR J Electron Commun Eng (IOSR-JECE) 4(5):60–68. e-ISSN 2278-2834, p-ISSN 2278-873510.9790/2834-0456068 ↗