journal article·2021-01-22Open access

Microstructure and Fracture Mechanism Investigation of Porous Silicon Nitride–Zirconia–Graphene Composite Using Multi-Scale and In-Situ Microscopy

Zhongquan Liao, Yvonne Standke, Jürgen Gluch, Katalin Balázsi, Onkar Pathak, Sören Höhn, Mathias Herrmann, Stephan Werner, Ján Dusza, Csaba Balázsi, Ehrenfried Zschech

Nanomaterials· Volume 11· Issue 2

Abstract

Silicon nitride–zirconia–graphene composites with high graphene content (5 wt.% and 30 wt.%) were sintered by gas pressure sintering (GPS). The effect of the multilayer graphene (MLG) content on microstructure and fracture mechanism is investigated by multi-scale and in-situ microscopy. Multi-scale microscopy confirms that the phases disperse evenly in the microstructure without obvious agglomeration. The MLG flakes well dispersed between ceramic matrix grains slow down the phase transformation from α to β-Si3N4, subsequent needle-like growth of β-Si3N4 rods and the densification due to the reduction in sintering additives particularly in the case with 30 wt.% MLG. The size distribution of Si3N4 phase shifts towards a larger size range with the increase in graphene content from 5 to 30 wt.%, while a higher graphene content (30 wt.%) hinders the growth of the ZrO2 phase. The composite with 30 wt.% MLG has a porosity of 47%, the one with 5 wt.% exhibits a porosity of approximately 30%. Both Si3N4/MLG composites show potential resistance to contact or indentation damage. Crack initiation and propagation, densification of the porous microstructure, and shift of ceramic phases are observed using in-situ transmission electron microscopy. The crack propagates through the ceramic/MLG interface and through both the ceramic and the non-ceramic components in the composite with low graphene content. However, the crack prefers to bypass ceramic phases in the composite with 30 wt.% MLG.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Advanced ceramic materials synthesis · Advanced materials and composites · Graphene research and applications

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

Fraunhofer Institute for Ceramic Technologies and Systems IKTS, Maria-Reiche-Straße 2, 01109 Dresden, Germany

Centre for Energy Research, Konkoly-Thege Str. 29-33, 1121 Budapest, Hungary

Fraunhofer Institute for Ceramic Technologies and Systems IKTS, Winterbergstraße 28, 01277 Dresden, Germany

Helmholtz Zentrum Berlin, Albert-Einstein-Straße 15, 12489 Berlin, Germany

Institute of Materials Research, Slovak Academy of Sciences, Watsonova 47, 040 01 Košice, Slovakia

Funding

Hungarian National Research Development and Innovation Office · Deutsche Forschungsgemeinschaft (DFG)

References (43)

Show source-provided references
1. Silicon nitride ceramics—Review of structure, processing and properties
2. Silicon nitride and related materials10.1111/j.1151-2916.2000.tb01182.x ↗
3. Relationships between processing, microstructure and properties of dense and reaction-bonded silicon nitride10.1007/BF01161167 ↗
4. Influence of graphene addition and sintering temperature on physical properties of Si3N4 matrix composites10.1016/j.ijrmhm.2016.02.003 ↗
5. Silicon nitride for high-temperature applications10.1111/j.1551-2916.2010.03839.x ↗
6. Wear analysis of silicon nitride cutting tool in dry machining of T6061 aluminium alloy10.4028/www.scientific.net/AMM.268-270.563 ↗
7. The influence of the graphene additive on mechanical properties and wear of hot-pressed Si3N4 matrix composites10.1016/j.jeurceramsoc.2014.08.004 ↗
8. Phase transformation of ZrO2 nanoparticles produced from zircon10.1080/01411594.2011.619698 ↗
9. The Tetragonal-Monoclinic Transformation in Zirconia: Lessons Learned and Future Trends10.1111/j.1551-2916.2009.03278.x ↗
10. Densification and mechanical properties of spark plasma sintered Si3N4/ZrO2 nano-composites10.1016/j.jallcom.2018.10.243 ↗
11. Processing of carbon nanotube reinforced silicon nitride composites by spark plasma sintering10.1016/j.compscitech.2004.10.006 ↗
12. Synthesis of conducting graphene/Si3N4 composites by spark plasma sintering10.1016/j.carbon.2013.02.015 ↗
13. Examination of milled h-BN addition on sintered Si3N4/h-BN ceramic composites10.2298/PAC1804357B ↗
14. Graphene and graphene oxide: Synthesis, properties, and applications10.1002/adma.201001068 ↗
15. Influence of processing on fracture toughness of Si3N4+ graphene platelet composites10.1016/j.jeurceramsoc.2013.01.025 ↗
16. Extraordinary toughening enhancement and flexural strength in Si3N4 composites using graphene sheets10.1016/j.jeurceramsoc.2013.08.039 ↗
17. Microstructure and fracture toughness of Si3N4+ graphene platelet composites10.1016/j.jeurceramsoc.2012.04.022 ↗
18. Fracture toughness and toughening mechanisms in graphene platelet reinforced Si3N4 composites10.1016/j.scriptamat.2012.02.009 ↗
19. Elastic properties of silicon nitride ceramics reinforced with graphene nanofillers10.1016/j.matdes.2015.08.044 ↗
20. Tribological properties of Si3N4-graphene nanocomposites10.1016/j.jeurceramsoc.2013.03.035 ↗
21. Wear damage of Si3N4-graphene nanocomposites at room and elevated temperatures10.1016/j.jeurceramsoc.2014.02.025 ↗
22. Thermal stability and conductivity of hot-pressed Si3N4-graphene composites10.1007/s10973-013-3565-6 ↗
23. Porous sandwich ceramic of layered silicon nitride-zirconia composite with various multilayered graphene content10.1016/j.jallcom.2020.154984 ↗
24. Graphene added multilayer ceramic sandwich (GMCS) composites: Structure, preparation and properties10.1016/j.jeurceramsoc.2020.01.054 ↗
25. Tunable and weakly negative permittivity in carbon/silicon nitride composites with different carbonizing temperatures10.1016/j.carbon.2017.09.037 ↗
26. Fabrication and properties of porous silicon nitride wave-transparent ceramics via gel-casting and pressureless sintering10.1016/j.msea.2016.03.116 ↗
27. Hertzian contact damage in porous alumina ceramics10.1111/j.1151-2916.1997.tb02940.x ↗
28. Hertzian contact damage in a highly porous silicon nitride ceramic10.1016/S0955-2219(02)00301-1 ↗
29. Identification of a damage criterion of a highly porous alumina ceramic10.1016/j.actamat.2016.01.071 ↗
30. Fabrication and properties of in situ silicon nitride nanowires reinforced porous silicon nitride (SNNWs/SN) compsites10.1016/j.jeurceramsoc.2018.02.001 ↗
31. Effect of agarose content on microstructures and mechanical properties of porous silicon nitride ceramics produced by gelcasting10.1631/jzus.A1000125 ↗
32. Fabrication of porous silicon nitride ceramics using binder jetting technology10.1088/1757-899X/140/1/012023 ↗
33. Silicon nitride composites with different nanocarbon additives10.4191/kcers.2012.49.4.352 ↗
34. Fast tomographic reconstruction on multicore computers10.1093/bioinformatics/btq692 ↗
35. Tutorial on the Visualization of Volumetric Data Using tomviz10.1017/S1551929517001213 ↗
36. Fiji: An open-source platform for biological-image analysis10.1038/nmeth.2019 ↗
37. Microstructural characteristics, porosity and strength development in ceramic-laterized concrete10.1016/j.cemconcomp.2017.11.017 ↗
38. Carbon reduction reaction in the Y2O3-SiO2 glass system at high temperature10.1016/S0955-2219(01)00231-X ↗
39. Low-cost preparation of Si3N4-SiC micro/nano composites by in-situ carbothermal reduction of silica in silicon nitride matrix10.1016/S0955-2219(03)00604-6 ↗
40. Influence of graphite additives on wear properties of hot pressed Si3N4 ceramics10.2109/jcersj.114.1061 ↗
41. Contact-damage-resistant ceramic/single-wall carbon nanotubes and ceramic/graphite composites10.1038/nmat1161 ↗
42. Structure design, fabrication, properties of laminated ceramics: A review
43. Structural design and energy absorption mechanism of laminated SiC/BN ceramics10.1016/j.jeurceramsoc.2018.04.052 ↗