Lift-off performance of electromagnetic acoustic transducers (EMATs) for surface acoustic wave generation
Source abstract
Abstract
Electromagnetic acoustic transducers (EMATs) have a behaviour that depends on the distance between the transducer and the surface of the material under test, namely the lift-off. Rayleigh waves generated by EMATs suffer from waveform distortion as the lift-off is increased. This paper describes this distortion numerically and experimentally, focusing on the spatial distribution of the induced currents and hence the ultrasound pulses. This is verified experimentally using an EMAT consisting of a magnet and a single 1.5 mm wide linear coil, showing a decrease in peak frequency for the wideband Rayleigh wave of the order of 100 kHz/mm with lift-off. The behaviour when using EMATs in an array configuration (equivalent to a meander-coil, where the current through neighbouring coils is in opposite directions) is then described. Coil spacing is shown to affect the lift-off behaviour, with the spatial model predicting well the frequency behaviour. The lift-off behaviours of physically spaced coils and those which are pulsed with time delays to give an effective separation are shown to be equivalent for all but the smallest separations; unless very small separations are required to give a high frequency signal, the effective spatial current distribution spread for a single coil counteracts the benefits of reducing the dipole effect. Good performance with lift-off variation is hard to achieve at high frequency, and lift-off must be considered if a particular frequency of operation is required.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Ultrasonics and Acoustic Wave Propagation · Non-Destructive Testing Techniques · Acoustic Wave Resonator Technologies
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (29)
Show source-provided references
1. Hirao · 2017
2. Physical principles of measurement with EMAT transducers
3. Analytical solutions to eddy-current probe-coil problems10.1063/1.1656680 ↗
4. High temperature EMAT design for scanning or fixed point operation on magnetite coated steel10.1016/j.ndteint.2017.04.001 ↗
5. Stress corrosion cracking detection using non-contact ultrasonic techniques10.1016/j.corsci.2013.10.018 ↗
6. Characterisation of defects in the railhead using ultrasonic surface waves10.1016/j.ndteint.2006.01.005 ↗
7. Effect of liftoff on accuracy of phase velocity measurements made with electromagnetic-acoustic transducers
8. Lift-off compensation for improved accuracy in ultrasonic lamb wave velocity measurements using electromagnetic acoustic transducers (EMATs)10.1016/j.ultras.2006.05.169 ↗
9. Study on the lift-off effect of EMAT10.1016/j.sna.2009.05.014 ↗
10. Influence of the lift-off effect on the cut-off frequency of the EMAT-generated Rayleigh wave signal10.3390/s141019687 ↗
11. Optimal design of spiral coil electromagnetic acoustic transducers considering lift-off sensitivity operating on non-ferromagnetic media10.1080/10589759.2016.1265963 ↗
12. A new electromagnetic acoustic transducer (EMAT) design for operation on rail10.1016/j.ndteint.2014.03.007 ↗
13. Coupling mechanism of electromagnetic acoustic transducers for ultrasonic generation10.1121/1.2184288 ↗
14. The effect of EMAT coil geometry on the Rayleigh wave frequency behaviour10.1016/j.ultras.2019.06.007 ↗
15. Numerical and experimental analysis of unidirectional meander-line coil electromagnetic acoustic transducers10.1109/TUFFC.2013.2864 ↗
16. A modified meander-line-coil EMAT design for signal amplitude enhancement10.1016/j.sna.2016.07.006 ↗
17. Design method of multiwavelength EMATs based on spatial domain harmonic control10.1109/TUFFC.2021.3055871 ↗
18. Phased electromagnetic acoustic transducer array for Rayleigh wave surface defect detection10.1109/TUFFC.2020.2968151 ↗
19. Electromagnetic acoustic transducer optimisation for surface wave applications10.1016/j.ndteint.2019.102142 ↗
20. Field distribution due to a circular current loop placed in an arbitrary position above a conducting plate10.1109/TGRS.1985.289468 ↗
21. Eddy currents in an infinite slab due to an elliptic current excitation10.1109/20.105058 ↗
22. Electromagnetic field distributions around conducting slabs, produced by eddy-current probes with arbitrary shape current-carrying excitation loops10.1049/ip-smt:20010483 ↗
23. Analytical model for tilted coils in eddy-current nondestructive inspection10.1109/TMAG.2005.854331 ↗
24. A model for pulsed Rayleigh wave and optimal EMAT design10.1016/j.sna.2006.01.048 ↗
25. Hughes · 2015
26. Kaye · 1995
27. Relative ability of wedge-coupled piezoelectric and meander coil EMAT probes to generate single-mode Lamb waves10.1109/TUFFC.2018.2800296 ↗
28. Homodyne detection of ultrasonic surface displacements using two-wave mixing in photorefractive polymers10.1016/S0030-4018(99)00023-1 ↗
29. Lift-off performance of ferrite enhanced generation EMATs