journal article·2024-06

Measurement and separation of forces and lift-offs employing an inductance-to-digital converters (LDC)-based orthogonal LC resonance sensor

Changrong Yang, Guiyun Tian, Qiuping Ma, Mark Robinson, Xiaolong Lu, Emmanuel Tashiwa Ibrahim, Wenjie Li

Publisher page

Abstract

© 2024 Elsevier LtdInductor-capacitor (LC) resonance sensors based on the sensing materials’ electromagnetic properties have potential to replace strain gauges for wheel-rail contact force measurement. However, as traditional eddy current testing acts, the lift-off effects also affect the results of the LC resonance sensing which can cause the misinterpretation between forces or lift-offs. This paper proposed an LDC-based orthogonal LC resonance sensor, combined with an 8-node quadratic interpolation method to achieve the measurement and accurate separation of forces and lift-offs. The four characteristic parameters of the orthogonal LC resonance sensor, Rp1, Frequency1, Rp2, Frequency2, were measured at different applied forces and lift-offs. A new combination pattern referred to the Rp2-Rp1, frequency2-frequency1 plane was proposed, which contained force and lift-off information in both vertical and transverse directions. Through the 8-node isoparametric coordinate transformation, the applied force and lift-off were separated respectively, with the maximum relative error of 22.61% for forces and 1.66% for lift-offs. Results indicated that the proposed method is effective and can be used to measure force/stress under varying lift-offs.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Non-Destructive Testing Techniques · Acoustic Wave Resonator Technologies · Sensor Technology and Measurement Systems

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (29)

Show source-provided references
1. A measurement and evaluation method for wheel-rail contact forces and axle stresses of high-speed train10.1016/j.measurement.2019.106983 ↗
2. Wheel-rail force measurement based on wireless LC resonance sensing10.1109/JSEN.2023.3288399 ↗
3. Challenges in improving the performance of eddy current testing: review10.1177/0020294018801382 ↗
4. Elimination of coil liftoff from eddy current measurements of conductivity10.1109/TIM.2013.2272842 ↗
5. Study of lift-off invariance for pulsed eddy-current signals10.1109/TMAG.2008.2006246 ↗
6. Lu · 2021 · 121
7. Conductivity Lift-off Invariance and measurement of permeability for ferrite metallic plates10.1016/j.ndteint.2018.01.007 ↗
8. A novel eddy current method for magnetic plate identification with elimination of lift-off effect10.14243/jsaem.27.165 ↗
9. Elimination of liftoff effect using a model-based method for eddy current characterization of a plate10.1016/j.ndteint.2015.05.007 ↗
10. Reduction of lift-off effects for pulsed eddy current NDT10.1016/j.ndteint.2004.09.007 ↗
11. Lift-off suppression based on combination of bridge and transformer signal conditionings of eddy current testing
12. Resistance-frequency eddy current method for electrical conductivity measurement
13. Lift-off effect in high-frequency eddy current conductivity spectroscopy10.1016/j.ndteint.2007.06.001 ↗
14. Eddy current residual stress profiling in surface-treated engine alloys10.1080/10589750802245280 ↗
15. Reduction of lift-off effect in high-frequency apparent eddy current conductivity spectroscopy10.1088/1361-6501/aa63aa ↗
16. Cook · 2002
17. Experimental evaluation of nonmagnetic metal clad thicknesses over nonmagnetic metals using apparent eddy current conductivity spectroscopy
18. Design and experimental research of stress measurement system for ferromagnetic components based on ACSM method10.1177/0309324721998107 ↗
19. Investigation of electromagnetic nondestructive evaluation of residual strain in low carbon steels using the eddy current magnetic signature (EC-MS) method10.1016/j.jmmm.2019.01.103 ↗
20. Stress detection and measurement in ferromagnetic metals using pulse electromagnetic method with U-shaped sensor10.1016/j.measurement.2017.04.001 ↗
21. A self-frequency-conversion eddy current testing method
22. Inductance-to-digital converters (LDC) based integrative multi-parameter eddy current testing sensors for NDT&E
23. LDC1101 1.8 V high-resolution, high-speed inductance-to-digital converter
24. Non-destructive techniques based on eddy current testing10.3390/s110302525 ↗
25. Scaling relation for the inductance of a coil on a ferromagnetic half-space10.1063/1.366197 ↗
26. Elastic and plastic strain effects on eddy current response of aluminium alloys10.1080/10589759.2013.785544 ↗
27. A stress measurement method for steel strands based on LC oscillation10.1155/2018/1584903 ↗
28. Decoupling the influence of permeability and conductivity in pulsed eddy-current measurements10.1109/TMAG.2012.2225634 ↗
29. Thin hybrid metamaterial slab with negative and zero permeability for high efficiency and low electromagnetic field in wireless power transfer systems10.1109/TEMC.2017.2751595 ↗