Damage resistance and anticorrosion properties of nanosilica-filled epoxy-resin composite coatings
Source abstract
Abstract
Abstract Silica nanoparticles surface-capped with diglycidyl ether of bisphenol A were dispersed in a solution of epoxy resin, hardener and acetone. The resultant suspension was then coated onto the surface of duplex stainless steel of type DSS 2205 and cured with temperature, generating a 50 μm thick silica/epoxy coating. Epoxy coating without nanosilica was also prepared as a reference in the same manner. Mechanical properties of these coatings were compared and characterized using the Vickers hardness test. Three-point bending test was performed in combination with acoustic emission to analyze the damage initiation and development in the coating. The effects of incorporating the silica particles on the surface characteristics and the corrosion resistance of the epoxy-coated steel were investigated with contact-angle and surface energy as well as by potentiodynamic polarization and electrochemical impedance spectroscopy in a 3.5 wt.% NaCl solution. Results indicate, that silica particles significantly improved the microstructure of the coating matrix, which was reflected in an increased damage resistance, reduced degree of delamination, increased surface roughness and induced hydrophobicity. The silica/epoxy coating was proven to serve as a successful barrier in a chloride-ion-rich environment with an enhanced anticorrosive performance, which was confirmed by the reduced corrosion rate.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Corrosion Behavior and Inhibition · Concrete Corrosion and Durability · Polymer Nanocomposites and Properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (33)
Show source-provided references
1. Evaluation of corrosion protection properties of additives for waterborne epoxy coatings on steel10.1016/S0300-9440(02)00016-4 ↗
2. Corrosion protective polyaniline epoxy blend coatings on mild steel10.1016/S0379-6779(98)01050-9 ↗
3. Stability of crack-propagation in epoxy-resins10.1016/0032-3861(77)90016-7 ↗
4. Epoxy nanocomposites with high mechanical and tribological performance10.1016/S0266-3538(03)00115-5 ↗
5. Crack-propagation in a glass particle-filled epoxy-resin 2. Effect of particle matrix adhesion10.1007/BF02403235 ↗
6. Parameters determining the strength and toughness of particulate filled epoxide-resins10.1007/BF01160743 ↗
7. Effects of wet ball-milling on particle dispersion and mechanical properties of particulate epoxy composites10.1016/0167-577X(95)00223-5 ↗
8. Polymer-layered silicate nanocomposites: synthesis, properties and applications10.1002/(SICI)1099-0739(199810/11)12:10/11<675::AID-AOC779>3.0.CO;2-V ↗
9. Clay-reinforced epoxy nanocomposites10.1021/cm00048a006 ↗
10. Intercalated clay nanocomposites: morphology, mechanics, and fracture behavior10.1002/polb.1090 ↗
11. Toughening of a brittle thermosetting polymer: effects of reinforcement particle size and volume fraction10.1023/A:1013844015493 ↗
12. Influence of particle-size and particle-size distribution on toughnening mechanisms in rubber-modified epoxies10.1007/BF01184979 ↗
13. Elastomers and thermoplastics as modifiers for thermosetting resins10.1002/masy.19930700127 ↗
14. Fracture of polymer networks based on diethylene glycol bis(allyl carbonate)10.1016/0032-3861(94)90661-0 ↗
15. Influence of rubber particle size on mechanical properties of polypropylene-SEBS blends10.1002/(SICI)1097-4628(19980620)68:12<1891::AID-APP1>3.0.CO;2-G ↗
16. The effect of dispersed paint particles on the mechanical properties of rubber toughened polypropylene composites10.1023/A:1004515300637 ↗
17. Fracture toughness of silica particulate-filled epoxy composite10.1002/app.11206 ↗
18. Fatigue crack growth behavior of silica particulate reinforced epoxy resin composite10.1016/j.compscitech.2011.02.015 ↗
19. Effect of particle size of nanosilica on the performance of epoxy/silica composite coatings10.1007/s10853-005-0714-8 ↗
20. Effects of surface properties of colloidal silica particles on redispersibility and properties of acrylic-based polyurethane/silica composites10.1016/j.jcis.2004.08.100 ↗
21. Preparation and characterization of polyester/silica nanocomposite resins10.1016/j.porgcoat.2004.03.013 ↗
22. Nanoporous titania interlayer as reservoir of corrosion inhibitors for coatings with self-healing ability10.1016/j.porgcoat.2006.08.029 ↗
23. Non-destructive evaluation of plasma sprayed functionally graded thermal barrier coatings10.1016/S0257-8972(00)00700-3 ↗
24. Real-time frequency determination of acoustic emission for different fracture mechanisms in carbon epoxy composites10.1016/0266-3538(95)00121-2 ↗
25. Controlled growth of monodisperse silica spheres in micron size range10.1016/0021-9797(68)90272-5 ↗
26. Fast fabrication of mesoporous SiC with high and highly ordered porosity from ordered silica templates
27. Growth of arrays of oriented epitaxial platinum nanoparticles with controlled size and shape by natural colloidal lithography10.1186/1556-276X-9-336 ↗
28. Amine-cured epoxy/clay nanocomposites. I. Processing and chemical characterization10.1002/polb.20288 ↗
29. A reformulation of the equation of state for interfacial-tensions10.1016/0021-9797(90)90067-X ↗
30. Contact angle measurement and contact angle interpretation10.1016/S0001-8686(98)00087-6 ↗
31. Fabrication of tunable superhydrophobic surfaces by nanosphere lithography10.1021/cm034696h ↗
32. Synthesis and characterization of organic–inorganic hybrid thin films from poly(acrylic) and monodispersed colloidal silica10.1016/S0032-3861(02)00824-8 ↗
33. The effect of polyhedral oligomeric silesquioxane dispersant and low surface energy additives on spectrally selective paint coatings with self-cleaning properties10.1016/j.solmat.2009.09.008 ↗