Study of friction stir joining of thin aluminium sheets in lap joint configuration
Source abstract
Abstract
Thinning in friction stir lap joints and its relation with the process variables was investigated. Friction stir welds were made on 1 mm thick AA6111 aluminium alloy sheets in order to study the effects of rotation rate, traverse speed, plunge depth, tilt angle and pin height on faying surface defects. Sheet thinning on the advancing and retreating sides was quantified and the lap shear strength of the joints was evaluated. A decrease in the pitch of the runs at constant rotation rate increased the sheet thinning and reduced the joint strength in a linear manner. Process pitch and pin height were found to be the most critical factors in determining the faying surface lift up. A pin of the same height as the sheet thickness resulted in maximum lap shear strength. Tool tilt did not show a significant effect on the sheet thinning.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: Advanced Welding Techniques Analysis · Aluminum Alloys Composites Properties · RFID technology advancements
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
Affiliations
Center for Friction Stir Processing, Department of Materials Science and Engineering, Missouri University of Science and Technology, Rolla, MO 65409, USA
GM R&D Center, Warren, MI 48090, USA
Pacific Northwest National Labs, Richland, WA 99356, USA
References (20)
Show source-provided references
1. Thomas W. M., Nicholas E. D., Needham J. C., Murch M. G., Templesmith P., and Dawes C. J.: GB patent application no. 9125978·8, December 1991.
2. 10.4271/2006-01-055510.4271/2006-01-0555 ↗
3. 10.1016/j.tws.2007.02.00710.1016/j.tws.2007.02.007 ↗
4. 10.1016/j.mser.2005.07.00110.1016/j.mser.2005.07.001 ↗
5. Mishra R. S., and Mahoney M. W. ‘Friction stir welding and processing’; 2007, Materials Park, OH, ASM International.
6. 10.1016/j.pmatsci.2008.05.00110.1016/j.pmatsci.2008.05.001 ↗
7. Dracup B. J., and Arbegast W. J. ‘Friction stir welding as a rivet replacement technology’, Proc. 1999 SAE Conf. on ‘Aerospace automated fastening’, Memphis, TN, USA, October 1999, SAE, Document no. 1999-01-3432.10.4271/1999-01-3432 ↗
8. Kumar K., and Kailas S. V. ‘An experimental analysis on a friction stir welding defect (Joint-line-remnant)’, Proc. Symp. on ‘Joining materials’, Tirichirapalli, Tamilnadu, India, December 2008, BHEL, Paper 4, 1085.
9. Cederqvist L. · Weld. J. Res. Suppl · 2001 · 80 · 281
10. 10.1361/1059949052231010.1361/10599490522310 ↗
11. 10.2320/matertrans.46.221110.2320/matertrans.46.2211 ↗
12. Yadava M., Mishra R. S., Chen Y. L., Gayden X. Q., and Grant G. J. ‘Study of friction-stir-lap-welds of AA6111 Al alloy’, in ‘Friction stir welding and processing IV’, 203–212; 2007, Warrendale, PA, TMS.
13. Li T., Ritter G., Kapustka N., and Lederich R. ‘‘Friction stir lap joining of Al 7075 with Sealant’, in ‘Friction stir welding and processing IV’, 193–201; 2007, Warrendale, PA, TMS.
14. 10.1007/s10853-008-2525-110.1007/s10853-008-2525-1 ↗
15. Soundararajan V. · J. Mater. Eng. Perform · 2007 · 16 · 49110.1007/s11665-007-9081-8 ↗
16. 10.1016/j.ijfatigue.2006.02.05210.1016/j.ijfatigue.2006.02.052 ↗
17. 10.1179/174329305X3930110.1179/174329305X39301 ↗
18. 10.1016/j.scriptamat.2007.10.04810.1016/j.scriptamat.2007.10.048 ↗
19. Guerra M., McClure J. C., Murr L. E., and Nunes A. C. ‘Metal flow during friction stir welding’, in ‘Friction stir welding and processing’, 25–34; 2001, Warrendale, PA, TMS.
20. Mishra R. S., and Mahoney M. W. ‘Friction stir welding and processing’, 16–18; 2007, Material, Park, OH, ASM International.