journal article·2016-10

Gas metal arc brazing of galvannealed steel sheets

P. Makwana, M. Shome, Sven-F. Goecke, A. De

Publisher page

Abstract

An advanced gas metal arc welding technique with controlled short-circuiting mode of metal transfer and arcing at low power was employed for brazing of galvannealed steels using CuSi3 filler wire. The brazed joints showed the presence of an interface layer with Fe–Si intermetallic compounds (IMC). Increase in heat input resulted in an increase of the interface layer thickness. The maximum failure load of 2.5 kN was achieved for a heat input of 105 J mm −1 with the corresponding interface layer thickness of 2.7 µm. Heat inputs beyond 105 J mm −1 led to excessive spatter of zinc and increase in interface layer thickness with hard Si-rich IMC. In contrast, heat input values lower than 80 J mm −1 produced inadequate wetting of the steel surface by the molten filler wire deposit and resulted in low joint strength.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Corrosion Behavior and Inhibition · High-Temperature Coating Behaviors · Hydrogen embrittlement and corrosion behaviors in metals

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

Indian Institute of Technology Bombay, Mumbai, Maharashtra, India

Tata Steel Ltd., Jamshedpur, Jharkhand, India

Technical University of Applied Science, Brandenburg an der Havel, Germany

References (34)

Show source-provided references
1. 10.1016/S0079-6425(98)00006-110.1016/S0079-6425(98)00006-1 ↗
2. 10.2355/isijinternational.42.87610.2355/isijinternational.42.876 ↗
3. 10.1179/stw.2000.5.1.4910.1179/stw.2000.5.1.49 ↗
4. 10.2320/matertrans.M201023910.2320/matertrans.M2010239 ↗
5. 10.1179/136217109X1257781448665610.1179/136217109X12577814486656 ↗
6. 10.1179/174329306X15318710.1179/174329306X153187 ↗
7. Basak S. · Weld. J. · 2013 · 92 · 29s
8. 10.1016/j.matdes.2004.11.01010.1016/j.matdes.2004.11.010 ↗
9. 10.1016/j.jmatprotec.2014.06.01710.1016/j.jmatprotec.2014.06.017 ↗
10. 10.1007/s40194-014-0146-710.1007/s40194-014-0146-7 ↗
11. 10.1007/s00170-014-6347-910.1007/s00170-014-6347-9 ↗
12. 10.1016/j.phpro.2014.08.07710.1016/j.phpro.2014.08.077 ↗
13. 10.1016/j.matdes.2013.06.05410.1016/j.matdes.2013.06.054 ↗
14. 10.2207/qjjws.31.26s10.2207/qjjws.31.26s ↗
15. 10.1007/s40194-015-0220-910.1007/s40194-015-0220-9 ↗
16. 10.1179/02670830422502213310.1179/026708304225022133 ↗
17. 10.1081/AMP-20006062110.1081/AMP-200060621 ↗
18. 10.1080/0950711070141190810.1080/09507110701411908 ↗
19. 10.1016/j.jmatprotec.2013.04.00410.1016/j.jmatprotec.2013.04.004 ↗
20. 10.1179/1362171815Y.000000003210.1179/1362171815Y.0000000032 ↗
21. Yang S. L. · Weld. J. · 2009 · 88 · 168s
22. 10.1016/j.jmatprotec.2013.08.00210.1016/j.jmatprotec.2013.08.002 ↗
23. 10.4028/www.scientific.net/MSF.575-578.71610.4028/www.scientific.net/MSF.575-578.716 ↗
24. 10.1016/S0921-5093(97)00680-110.1016/S0921-5093(97)00680-1 ↗
25. BS EN 12797:2000: ‘Brazing – Destructive tests of brazed joints’, 15–16; 2004, London, British Standard.
26. 10.1179/1362171810Y.000000002910.1179/1362171810Y.0000000029 ↗
27. Klepser C. A. ‘Growth of intermetallic phases at low temperature’, DSc Thesis, Massachusetts Institute of Technology, Cambridge, MA, USA, 1996, 23–24.
28. Bakker H., Bonzel H. P., Bruff C. M., Dayananda M. A., Gust W., Horvath J., Kaur I., Kidson G. V., Le Claire A. D., Mehrer H., Murch G. E., Neumann G., Stolica N., and Stolwijk N. A. ‘Diffusion in solid metals and alloys’, 1st edn, 137–138; 1990, Germany, Springer.
29. Grong O. ‘Metallurgical modelling of welding’, 2nd edn, 45–54; 1997, London, The Institute of Materials.
30. 10.1016/S1003-6326(07)60026-010.1016/S1003-6326(07)60026-0 ↗
31. 10.1016/S0966-9795(02)00046-810.1016/S0966-9795(02)00046-8 ↗
32. 10.1007/BF0266423110.1007/BF02664231 ↗
33. 10.1016/j.ijheatmasstransfer.2006.08.02510.1016/j.ijheatmasstransfer.2006.08.025 ↗
34. Gale W. F. · 2004