journal article·2025-04

Enhanced spray cooling on patterned perforated micromesh surface

Yongyan Hu, Xiuliang Liu, Ronggui Yang

Publisher page

Abstract

The increasing power density in applications such as aerospace, nuclear power, laser weapons, and phased array radar has led to a growing demand for efficient thermal management technologies. Spray cooling, known for its high heat flux dissipation and excellent temperature uniformity, has garnered great interest. Micro/nano-structured surfaces have been adopted to enhance spray cooling, especially in the phase-change heat transfer regime. However, manipulating bubble dynamics for non-interfering liquid and vapor flow paths remains a challenge under high heat flux conditions. This work employs a cost-effective laser drilling technique to fabricate patterned multilayer perforated copper micromesh surfaces to enhance spray cooling. By creating separated liquid-vapor flow paths, bubble escape resistance is reduced, and the formation of vapor blankets within the perforated micromesh stack is delayed. Increasing the diameter and decreasing the separation between the perforations can strengthen the liquid and vapor transport, while reducing the liquid film boiling area. An analysis of flow resistance along bubble escape paths, caused by the anisotropic permeability of the multilayer micromesh in different directions, is performed to optimize the design of perforated microporous structures. A critical heat flux (CHF) of 1213 W/cm2, with a heat transfer coefficient (HTC) of 352.6 kW/(m2K), is achieved on the patterned perforated micromesh surface, which is an improvement of 115% and 142%, respectively, compared to the plain surface.
Source: expertdata · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Fluid Dynamics and Heat Transfer · Electrohydrodynamics and Fluid Dynamics · Fluid Dynamics and Thin Films

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (34)

Show source-provided references
1. Wang J X, Guo W, Xiong K, et al. Review of aerospace-oriented spray cooling technology. Prog Aerospace Sci, 2020, 116: 10063510.1016/j.paerosci.2020.100635 ↗
2. Nilsson J, Payne D N. High-power fiber lasers. Science, 2011, 332: 921–92210.1126/science.1194863 ↗
3. Kandlikar S G, Bapat A V. Evaluation of jet impingement, spray and microchannel chip cooling options for high heat flux removal. Heat Transfer Eng, 2007, 28: 911–92310.1080/01457630701421703 ↗
4. Xu R, Wang G, Jiang P. Spray cooling on enhanced surfaces: A review of the progress and mechanisms. J Electron Packag, 2022, 144: 01080210.1115/1.4050046 ↗
5. Liu P, Kandasamy R, Ho J Y, et al. Dynamic performance analysis and thermal modelling of a novel two-phase spray cooled rack system for data center cooling. Energy, 2023, 269: 12683510.1016/j.energy.2023.126835 ↗
6. Ndao S, Peles Y, Jensen M K. Effects of pin fin shape and configuration on the single-phase heat transfer characteristics of jet impingement on micro pin fins. Int J Heat Mass Transfer, 2014, 70: 856–86310.1016/j.ijheatmasstransfer.2013.11.062 ↗
7. Li W, Qu X, Alam T, et al. Enhanced flow boiling in microchannels through integrating multiple micro-nozzles and reentry microcavities. Appl Phys Lett, 2017, 110: 01410410.1063/1.4973495 ↗
8. Kim J. Spray cooling heat transfer: The state of the art. Int J Heat Fluid Flow, 2007, 28: 753–76710.1016/j.ijheatfluidflow.2006.09.003 ↗
9. Chen R H, Chow L C, Navedo J E. Effects of spray characteristics on critical heat flux in subcooled water spray cooling. Int J Heat Mass Transfer, 2002, 45: 4033–404310.1016/S0017-9310(02)00113-8 ↗
10. Li W Q, Liu Y W, Liu Y Q, et al. Experimental study on spray heat transfer enhancement by micro-structured surface with nanoencapsulated phase change material slurry (NPCMS). Int J Heat Mass Transfer, 2024, 219: 12489210.1016/j.ijheatmasstransfer.2023.124892 ↗
11. Rini D P, Chen R H, Chow L C. Bubble behavior and nucleate boiling heat transfer in saturated FC-72 spray cooling. J Heat Transfer, 2001, 124: 63–7210.1115/1.1418365 ↗
12. Cheng W L, Peng Y H, Chen H, et al. Experimental investigation on the heat transfer characteristics of vacuum spray flash evaporation cooling. Int J Heat Mass Transfer, 2016, 102: 233–24010.1016/j.ijheatmasstransfer.2016.05.140 ↗
13. Zhang Z W, Hu D H, Li Q, et al. Visualization study on atomization characteristics and heat transfer performance of R1336mzz flash spray cooling. Sci China Tech Sci, 2021, 64: 2099–210910.1007/s11431-021-1853-4 ↗
14. Chow L C, Sehmbey M S, Pais M R. High heat flux spray cooling. Annu Rev Heat Transfer, 1997, 8: 291–31810.1615/AnnualRevHeatTransfer.v8.80 ↗
15. Peng C, Xu X H, Li Y M, et al. Experimental study on spray cooling under reduced pressures. Sci China Tech Sci, 2019, 62: 349–35510.1007/s11431-018-9370-y ↗
16. Silk E A, Kim J, Kiger K. Spray cooling of enhanced surfaces: Impact of structured surface geometry and spray axis inclination. Int J Heat Mass Transfer, 2006, 49: 4910–492010.1016/j.ijheatmasstransfer.2006.05.031 ↗
17. Liu N, Li L, Kang Y T. Experimental study on heat transfer performance enhancement by micro-structured surfaces for inclination spray application. Int J Heat Mass Transfer, 2019, 133: 631–64010.1016/j.ijheatmasstransfer.2018.12.177 ↗
18. Visaria M, Mudawar I. Effects of high subcooling on two-phase spray cooling and critical heat flux. Int J Heat Mass Transfer, 2008, 51: 5269–527810.1016/j.ijheatmasstransfer.2008.02.045 ↗
19. Mudawar I, Estes K A. Optimizing and predicting CHF in spray cooling of a square surface. J Heat Transfer, 1996, 118: 672–67910.1115/1.2822685 ↗
20. Hsieh C C, Yao S C. Evaporative heat transfer characteristics of a water spray on micro-structured silicon surfaces. Int J Heat Mass Transfer, 2006, 49: 962–97410.1016/j.ijheatmasstransfer.2005.09.013 ↗
21. Bostanci H, Singh V, Kizito J P, et al. Microscale surface modifications for heat transfer enhancement. ACS Appl Mater Interfaces, 2013, 5: 9572–957810.1021/am402512f ↗
22. Salman A S, Abdulrazzaq N M, Oudah S K, et al. Experimental investigation of the impact of geometrical surface modification on spray cooling heat transfer performance in the non-boiling regime. Int J Heat Mass Transfer, 2019, 133: 330–34010.1016/j.ijheatmasstransfer.2018.12.058 ↗
23. Sodtke C, Stephan P. Spray cooling on micro structured surfaces. Int J Heat Mass Transfer, 2007, 50: 4089–409710.1016/j.ijheatmasstransfer.2006.12.037 ↗
24. Zhang Z, Jiang P X, Ouyang X L, et al. Experimental investigation of spray cooling on smooth and micro-structured surfaces. Int J Heat Mass Transfer, 2014, 76: 366–37510.1016/j.ijheatmasstransfer.2014.04.010 ↗
25. Alvarado J L, Lin Y P. Multiple droplet impingements on nanostructured surfaces for enhanced spray cooling. In: ASME/JSME 2011 8th Thermal Engineering Joint Conference. Honolulu, 2011
26. Ulson de Souza A G, Barbosa Jr. J R. Spray cooling of plain and copper-foam enhanced surfaces. Exp Therm Fluid Sci, 2012, 39: 198–20610.1016/j.expthermflusci.2012.01.024 ↗
27. Thiagarajan S J, Narumanchi S, Yang R. Effect of flow rate and subcooling on spray heat transfer on microporous copper surfaces. Int J Heat Mass Transfer, 2014, 69: 493–50510.1016/j.ijheatmasstransfer.2013.09.033 ↗
28. Silk E A, Bracken P. Spray cooling heat flux performance using POCO HTC foam. J Thermophys Heat Transfer, 2010, 24: 157–16410.2514/1.44089 ↗
29. Hu Y, Lei Y, Liu X, et al. Heat transfer enhancement of spray cooling by copper micromesh surface. Mater Today Phys, 2022, 28: 10085710.1016/j.mtphys.2022.100857 ↗
30. Ni Q, Lu W, Ling X. Experimental and computational investigation on synergistic enhancement spray cooling using micropillars and capillary-driven wicking hybrid structures. Int J Heat Mass Transfer, 2023, 217: 12464310.1016/j.ijheatmasstransfer.2023.124643 ↗
31. Wang J X, Li Y Z, Mao Y F, et al. Comparative study of the heating surface impact on porous-material-involved spray system for electronic cooling: An experimental approach. Appl Therm Eng, 2018, 135: 537–54810.1016/j.applthermaleng.2018.02.055 ↗
32. Estes K A, Mudawar I. Correlation of sauter mean diameter and critical heat flux for spray cooling of small surfaces. Int J Heat Mass Transfer, 1995, 38: 2985–299610.1016/0017-9310(95)00046-C ↗
33. Zhao D, Qian X, Gu X, et al. Measurement techniques for thermal conductivity and interfacial thermal conductance of bulk and thin film materials. J Electron Packag, 2016, 138: 04080210.1115/1.4034605 ↗
34. Klinkenberge L. The permeability of porous media to liquids and gases. Drill Prod Prac, 1941, 200–213