Evolution of surface microstructure of Cu-50Cr alloy treated by high current pulsed electron beam
Source abstract
Abstract
A Cu-50Cr alloy was treated by the high current pulsed electron beam (HCPEB) at 20 and 30 keV with pulse numbers ranging from 1 to 100. Surface morphologies and microstructures of specimens before and after the treatments were investigated by employing scanning electron microscopy and X-ray diffraction. Results show that the HCPEB technique is able to induce remarkable surface modifications for the Cu-50Cr alloy. Cracks in Cr phases appear even after one-pulse treatment and their density always increases with the pulse number. Formation reason for these cracks is attributed to quasi-static thermal stresses accumulated along the specimen surface. Craters with typical morphologies are formed due to the dynamic thermal field induced by the HCPEB and they are found to prefer the sites near cracks or boundaries between neighboring Cr phases. Another microstructural characteristic produced by the HCPEB is the fine Cr spheroids, which are determined to be due to occurrence of liquid phase separation in the Cu-50Cr alloy. Finally, a general microstructural evolution profile that incorporates various HCPEB-induced surface features is tentatively outlined.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Pulsed Power Technology Applications · Integrated Circuits and Semiconductor Failure Analysis · Electrostatic Discharge in Electronics
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (43)
Show source-provided references
1. Slade P G. Advances in material development for high power, vacuum interrupter contacts. IEEE Trans CPMT, 1994, 17: 96–106
2. Rieder W F, Schussek M, Glatzle W, et al. The influence of composition and Cr particle size of Cu/Cr contacts on chopping current, contact resistance, and breakdown voltage in vacuum interrupters. IEEE Trans CPMT, 1989, 12: 273–283
3. Wang Y P, Ding B J. The preparation and the properties of microcrystalline and nanocrystalline CuCr contact materials. IEEE Trans CPMT, 1999, 22: 467–472
4. Ding B J, Yang Z M, Wang X T. Influence of microstructure on dielectric strength of CuCr contact materials in a vacuum. IEEE Trans CPMT, 1996, 19: 76–81
5. Yang Z M. Dissertation for the Doctor Degree. Xi’an: Xi’an Jiaotong University, 1996
6. Morris D G, Morris M A. Rapid solidification and mechanical alloying techniques applied to Cu-Cr alloys. Mater Sci Eng A, 1988, 104: 201–21310.1016/0025-5416(88)90422-3 ↗
7. Zhang C, Wang Y, Yang Z, et al. Microstructure and properties of vacuum induction melted CuCr25 alloys. J Alloy Compd, 2004, 366: 289–29210.1016/j.jallcom.2003.07.001 ↗
8. Zhou Z M, Wang Y P, Gao J, et al. Microstructure of rapidly solidified Cu-25wt.% Cr alloys. Mater Sci Eng A, 2005, 398: 318–32210.1016/j.msea.2005.03.095 ↗
9. Gao J, Wang Y P, Zhou Z M, et al. Phase separation in undercooled Cu-Cr melts. Mater Sci Eng A, 2007, 449–451: 654–65710.1016/j.msea.2006.02.379 ↗
10. Lamperti A, Ossi P M, Rotshtein V P. Surface analytical chemical imaging and morphology of Cu-Cr alloy. Surf Coat Technol, 2006, 200: 6373–637710.1016/j.surfcoat.2005.11.103 ↗
11. Lamperti A, Ossi P M. SIMS direct surface imaging of Cu1−x Crx formation. Appl Surf Sci, 2006, 252: 2288–229610.1016/j.apsusc.2005.04.015 ↗
12. Geng HR, Liu Y, Chen CZ, et al. Laser surface remelting of Cu-Cr-Fe contact material. Mater Sci Technol, 2000, 16: 564–56710.1179/026708300101508081 ↗
13. Hirose A, Kobayashi K F. Surface alloying of cupper with chromium by CO2 laser. Mater Sci Eng A, 1994, 174: 199–20610.1016/0921-5093(94)91089-8 ↗
14. Dong C, Wu A, Hao S, et al. Surface treatment by high current pulsed electron beam. Surf Coat Technol, 2003, 163–164: 620–62410.1016/S0257-8972(02)00657-6 ↗
15. Proskurovsky D I, Rotshtein V P, Ozur G E, et al. Physical foundations for surface treatment of materials with low energy, high current electron beams. Surf Coat Technol, 2000, 125: 49–5610.1016/S0257-8972(99)00604-0 ↗
16. Proskurovsky D I, Rotshtein V P, Ozur G E, et al. Pulsed electron-beam technology for surface modification of metallic materials. J Vac Sci Technol A, 1998, 16: 2480–248810.1116/1.581369 ↗
17. Hao Y, Gao B, Tu G F, et al. Surface modification of Al-12.6Si alloy by high current pulsed electron beam. Appl Surf Sci, 2012, 258: 2052–205610.1016/j.apsusc.2011.04.104 ↗
18. Hao Y, Gao B, Tu G F, et al. Surface modification of Al-20Si alloy by high current pulsed electron beam. Appl Surf Sci, 2011, 257: 3913–391910.1016/j.apsusc.2010.11.118 ↗
19. Hao S, Gao B, Wu A, et al. Surface modification of steels and magnesium alloy by high current pulsed electron beam. Nucl Inst Meth Phys Res B, 2005, 240: 646–65210.1016/j.nimb.2005.04.117 ↗
20. Gao B, Hao S, Zou J, et al. High current pulsed electron beam treatment of AZ31 Mg alloy. J Vac Sci Technol A, 2005, 23: 1548–155310.1116/1.2049299 ↗
21. Gao Y K. Influence of pulsed electron beam treatment on micro structure and properties of TA15 titanium alloy. Appl Surf Sci, 2013, 264: 633–63510.1016/j.apsusc.2012.10.083 ↗
22. Gao Y K. Surface modification of TC4 titanium alloy by high current pulsed electron beam (HCPEB) with different pulsed energy densities. J Alloy Compd, 2013, 572: 180–18510.1016/j.jallcom.2013.04.002 ↗
23. Zhang X D, Zou J X, Weber S, et al. Microstructure and property modifications in a near α Ti alloy induced by pulsed electron beam surface treatment. Surf Coat Technol, 2011, 206: 295–30410.1016/j.surfcoat.2011.07.017 ↗
24. Zhang X D, Hao S Z, Li X N, et al. Surface modification of pure titanium by pulsed electron beam. Appl Surf Sci, 2011, 257: 5899–5902.10.1016/j.apsusc.2011.01.136 ↗
25. Zou J X, Zhang K M, Grosdidier T, et al. Orientation-dependent deformation on 316L stainless steel induced by high-current pulsed electron beam irradiation. Mater Sci Eng A, 2008, 483–484: 302–30510.1016/j.msea.2006.07.179 ↗
26. Zou J, Zhang K, Dong C, et al. Selective surface purification via crater eruption under pulsed electron beam irradiation. Appl Phys Lett, 2006, 89: 04191310.1063/1.2234306 ↗
27. Grosdidier T, Zou J X, Stein N, et al. Texture modification, grain refinement and improved hardness/corrosion balance of a FeAl alloy by pulsed electron beam surface treatment in the “heating mode”. Scripta Mater, 2008, 58: 1058–106110.1016/j.scriptamat.2008.01.052 ↗
28. Zhang K, Zou J, Grosdidier T, et al. Improved pitting corrosion resistance of AISI 316L stainless steel treated by high current pulsed electron beam. Surf Coat Technol, 2006, 201: 1393–140010.1016/j.surfcoat.2006.02.008 ↗
29. Zhang K M, Yang D Z, Zou J X, et al. Improved in vitro corrosion resistance of a NiTi alloy by high current pulsed electron beam treatment. Surf Coat Technol, 2006, 201: 3096–310210.1016/j.surfcoat.2006.06.030 ↗
30. Zeng K, Hämäläinen M. Thermodynamic analysis of stable and metastable equilibria in the Cu-Cr system. Calphad, 1995, 19: 93–10410.1016/0364-5916(95)00010-C ↗
31. Qin Y, Dong C, Wang X, et al. Temperature profile and crater formation induced in high-current pulsed electron beam processing. J Vac Sci Technol A, 2003, 21: 1934–193810.1116/1.1619417 ↗
32. Zou J, Grosdidier T, Zhang K, et al. Mechanisms of nanostructure and metastable phase formations in the surface melted layers of a HCPEB-treated D2 steel. Acta Mater, 2006, 54: 5409–541910.1016/j.actamat.2006.05.053 ↗
33. Zhou Z M, Gao J, Li F, et al. Experimental determination and thermodynamic modeling of phase equilibria in the Cu-Cr system. J Mater Sci, 2011, 46: 7039–704510.1007/s10853-011-5672-8 ↗
34. Wei X, Wang J, Yang Z, et al. Liquid phase separation of Cu-Cr alloys during the vacuum breakdown. J Alloy Compd, 2011, 509: 7116–712010.1016/j.jallcom.2011.04.017 ↗
35. Zhou Z M, Gao J, Li F, et al. On the metastable miscibility gap in liquid Cu-Cr alloys. J Mater Sci, 2009, 44: 3793–379910.1007/s10853-009-3511-y ↗
36. Sun Z, Wang Y, Guo J, et al. Liquid and solid phase separation during melt spinning and annealing in melt-spun Cu-Cr ribbons. Mater Sci Eng A, 2007, 452-453: 411–41610.1016/j.msea.2006.10.112 ↗
37. Qin Y, Zou J, Dong C, et al. Temperature-stress fields and related phenomena induced by a high current pulsed electron beam. Nucl Inst Meth Phys Res B, 2004, 225: 544–55410.1016/j.nimb.2004.06.008 ↗
38. Pogrebnjak A D, Mikhaliov A D, Pogrebnjak Jr N A, et al. Evolution of vacancy defects and dislocations in surface layers of iron as a result of pulsed electron beam treatment. Phys Lett A, 1998, 241: 357–36310.1016/S0375-9601(98)00131-5 ↗
39. Zhang Z, Yang S, Lv P, et al. The microstructures and corrosion properties of polycrystalline copper induced by high-current pulsed electron beam. Appl Surf Sci, 2014, 294: 9–1410.1016/j.apsusc.2013.12.178 ↗
40. Kaufman L. Coupled phase diagrams and thermochemical data for transition metal binary systems-III. Calphad, 1978, 2: 117–14610.1016/0364-5916(78)90031-7 ↗
41. Sun Z, Zhang C, Zhu Y, et al. Microstructures of melt-spun Cu100−x -Crx (x=3.4–25) ribbons. J Alloy Compd, 2003, 361: 165–16810.1016/S0925-8388(03)00425-0 ↗
42. Correia J B, Davies H A, Sellars C M. Strengthening in rapidly solidified age hardened Cu-Cr and Cu-Cr-Zr alloys. Acta Mater, 1997, 45: 177–19010.1016/S1359-6454(96)00142-5 ↗
43. Morris M A, Morris D G. Microstructures and mechanical properties of rapidly solidified Cu-Cr alloys. Acta Metall, 1987, 35: 2511–252210.1016/0001-6160(87)90148-9 ↗