journal article·2013-10

Effects of blade bowing on the performance of a high pressure-ratio turbocharger centrifugal compressor with self-recirculation casing treatment

XinQian Zheng, ChuanJie Lan

Publisher page

Abstract

The effects of blade bowing on the performance of a high pressure-ratio turbocharger centrifugal compressor were studied by experiments and numerical simulation. The results showed that the negative bowing was capable of increasing the choke mass rate and the efficiency but decreased the surge mass flow rate, while the positive bowing had the opposite effects. When coupling with the self-recirculation casing treatment, the surge mass flow rate of the compressor with negative bowing blade was almost identical with that of the prototype, while the choke mass flow rate was still larger, and the total effect contributed to an increase of the stable flow range by 5.85% at design speed. Besides, the flow mechanism of the coupling effects of blade bowing and self-recirculation casing treatment was discussed.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Turbomachinery Performance and Optimization · Combustion and flame dynamics · Aerodynamics and Fluid Dynamics Research

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (21)

Show source-provided references
1. Krain H, Karpinski G, Beversdorff M. Flow analysis in a transonic centrifugal compressor rotor using 3-component laser velocimetry. ASME Paper No. 2001-GT-0315, 2001
2. Ibaraki S, Furukawa M, Iwakiri K, et al. Vortical flow structure and loss generation process in a transonic centrifugal compressor impeller. ASME Paper No. GT 2007-27791, 2007
3. Arnulfi G L, Blanchini F, Giannattasio P, et al. Extensive study on the control of centrifugal compressor surge. Proc IMechE Part A: J Power Energy, 2006, 220(3): 289–30410.1243/09576509JPE141 ↗
4. Arnulfi G L, Giannattasio P, Giusto C, et al. Multistage centrifugal compressor surge analysis: part ii-numeical simulation and dynamic control parameters evaluation. J Turbomach, 1999, 121(2): 312–32010.1115/1.2841316 ↗
5. Saha S L, Kurokawa J, Matsui J, et al. Passive control of rotating stall in a parallel-wall vaned diffuser by J-grooves. J Fluid Eng-T ASME, 2001, 123(3): 507–51510.1115/1.1374214 ↗
6. Asaga Y, Mizuki S, Tsujita H, et al. Surge control of a centrifugal compression system by using a bouncing ball. J Therm Sci, 2008, 17(2): 141–14610.1007/s11630-008-0141-7 ↗
7. Fisher F B. Application of map width enhancement devices to turbocharger compressor stages. SAE Trans, 1989, 97(6): 1303–1310
8. Zheng X Q, Zhang Y J, Yang M Y, et al. Stability improvement of high-pressure-ratio turbocharger centrifugal compressor by asymmetric flow control: Part II-non-axisymmetric self recirculation casing treatment. ASME Paper No. GT 2010-22582, 2010
9. Tamaki H, Masaru U, Kawakubo T, et al. Aerodynamic design to increase pressure ratio of centrifugal compressors for turbochargers. ASME Paper No. GT 2009-59160, 2009
10. Hunziker R, Dickmann H P, Emmrich R. Numerical and experimental investigation of a centrifugal compressor with an inducer casing bleed system. Proc IMechE Part A: J Power Energy, 2001, 215(6): 783–79110.1243/0957650011538910 ↗
11. Ishida M, Sakaguchi D, Ueki H. Optimization of inlet ring groove arrangement for suppression of unstable flow in a centrifugal impeller. ASME Paper No. GT 2005-68675, 2005
12. Ishida M, Surana D, Ueki H, et al. Suppression of unstable flow at small flow rates in a centrifugal blower by controlling tip leakage flow and reverse flow. J Turbomach, 2005, 127(1): 76–8310.1115/1.1811092 ↗
13. Khalfallah S, Ghenaiet A. Analyses of radial compressor stability improvement by casing treatment. Proc IMechE Part A: J Power Energy, 2012, 226(7): 807–82110.1177/0957650912458756 ↗
14. Weigold H D, Neubert R J, Behlke R F, et al. Bowed stators: an example of CFD applied to improve multistage compressor efficiency. J Turbomach, 1997, 199(2): 161–16810.1115/1.2841086 ↗
15. Benini E. Three-dimensional multi-objective design optimization of a transonic compressor rotor. J Propul Power, 2004, 20(4): 559–56510.2514/1.2703 ↗
16. Gallimore S J, Bolger J J, Cumpsty N A, et al. The use of sweep and dihedral in multistage axial flow compressor blading — Part I: University research and methods development. J Turbomach, 2002, 124(4): 521–53210.1115/1.1507333 ↗
17. Vad J. Aerodynamic effects of blade sweep and skew in low-speed axial flow rotors at the design flow rate: an overview. Proc IMechE Part A: J Power Energy, 2008, 222: 69–8510.1243/09576509JPE471 ↗
18. Fischer A, Riess W, Seume R J. Performance of strongly bowed stators in a 4-stage high speed compressor. ASME Paper GT2003-38392, 2003
19. Gummer V, Wenger U, Kau H P. Using sweep and dihedral to control three-dimensional flow in transonic stators of axial compressors. J Turbomach, 2001, 123(1): 40–4810.1115/1.1330268 ↗
20. Lin Y, Zheng X Q, Jin L, et al. A novel experimental method to evaluate the impact of the volute’s asymmetry on the performance of a high pressure-ratio turbocharger compressor. Sci China Tech Sci, 2012, 55(6): 1695–170010.1007/s11431-012-4822-9 ↗
21. Zheng X Q, Huenteler J, Yang M Y, et al. Influence of the volute on the flow in a centrifugal compressor of a high-pressure-ratio turbocharger. Proc IMechE Part A: J Power Energy, 2010, 224(8): 1157–116910.1243/09576509JPE968 ↗