Effects of stick-slip on stress intensity factors for subsurface short cracks in rolling contact
Source abstract
Abstract
This paper theoretically investigates the effects of stick-slip in rolling contact zone on stress intensity factors (SIFs) for subsurface short cracks. New mathematical models for SIFs including stick-slip ratio are deduced in two cases. One is a subsurface short crack parallel to surface, and the numerical analysis shows that the value of K II increases with the increase of stick-slip ratio; the other is a subsurface short crack perpendicular to the surface, and the numerical analysis indicates that the positive value of K I decreases with the increase of stick-slip ratio. As ΔK I and ΔK II are necessary to evaluate the fatigue crack propagation rate or fatigue lifetime, the influences of stick-slip ratio on them are then discussed. It is found that the maximum variations of ΔK I and ΔK II are both around 3.0% due to stick-slip ratio variation.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Mechanical stress and fatigue analysis · Railway Engineering and Dynamics · Fatigue and fracture mechanics
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (25)
Show source-provided references
1. Kalker J J. Three-dimensional Elastic Bodies in Rolling Contact. Dordrecht: Kluwer Academic Publishers, 1990. 40–6210.1007/978-94-015-7889-9 ↗
2. Suresh S, Ritchie R O. Propagation of short fatigue cracks. Int Mater Rev, 1984, 29(1): 445–47510.1179/imr.1984.29.1.445 ↗
3. Carter F W. On the action of a locomotive driving wheel. Proc Royal Soc London A, 1926, 112: 151–15710.1098/rspa.1926.0100 ↗
4. Haines D J, Ollerton E. Contact stress distributions on elliptical contact surfaces subjected to radial and tangential forces. Proc Inst Mech Eng, 1963, 177(1): 95–11410.1243/PIME_PROC_1963_177_014_02 ↗
5. Haines D J. Contact stresses in flat elliptical contact surfaces which support radial and shearing forces during rolling. Proc Inst Mech Eng, 1964, 179(10): 154–168
6. Lee A J C, Ollerton E. A photoelastic investigation of contact stresses in equal spheres rolling together with spin. J Strain Anal Eng, 1969, 4(3): 219–22710.1243/03093247V043219 ↗
7. Johnson K L. The effect of a tangential contact force upon the rolling motion of an elastic sphere on a plane. J Appl Mech, 1958, 25: 339–34610.1115/1.4011823 ↗
8. Kaneta M, Murakami Y, Okazaki T. Growth mechanism of subsurface crack due to Hertzian contact. J Tribol, 1986, 108: 134–13910.1115/1.3261133 ↗
9. Keer L M, Bryant M D, Haritos G K. Subsurface and surface cracking due to Hertzian contact. J Lubr Technol, 1982, 104: 347–35110.1115/1.3253217 ↗
10. Keer L M, Bryant M D. A pitting model for rolling contact fatigue. J Lubr Technol, 1983, 105: 198–20510.1115/1.3254565 ↗
11. Murakami Y, Kaneta M, Yatsuzuka H. Analysis of surface crack propagation in lubricated rolling contact. ASLE Trans, 1985, 28(1): 60–6810.1080/05698198508981595 ↗
12. Glodez S, Ren Z. Modelling of crack growth under cyclic contact loading. Theor Appl Fract Mec, 1998, 30: 159–17310.1016/S0167-8442(98)00053-6 ↗
13. Ren Z, Glodez S, Fajdiga G, et al. Surface initiated crack growth simulation in moving lubricated contact. Theor Appl Fract Mec, 2002, 38: 141–14910.1016/S0167-8442(02)00091-5 ↗
14. Hu Y D, Hu Z Z, Cao S Z. Theoretical study on Manson-Coffin equation for physically short cracks and lifetime prediction. Sci China Tech Sci, 2012, 55(1): 34–4210.1007/s11431-011-4581-z ↗
15. Peng D, Jones R, Constable T, et al. The tool for assessing the damage tolerance of railway wheel under service conditions. Theor Appl Fract Mec, 2012, 57: 1–1310.1016/j.tafmec.2011.12.002 ↗
16. Peng D, Jones R. The development of combination mechanical contact and thermal braking loads for railway wheel fatigue analysis. Theor Appl Fract Mec, 2012, 60(1): 10–1410.1016/j.tafmec.2012.06.002 ↗
17. Guan M F, Yu H. In-situ investigation on the fatigue crack propagation behavior in ferrite-pearlite and dual-phase ferrite-bainite low carbon steels. Sci China Tech Sci, 2013, 56(1):71–7910.1007/s11431-012-5047-7 ↗
18. Hearle A D, Johnson K L. Mode II stress intensity factor for a crack parallel to the surface of an elastic half-space subjected to a moving point load. J Mech Phys Solids, 1985, 33(1): 61–8110.1016/0022-5096(85)90022-5 ↗
19. Sheppard S, Barber J R, Comninou M. Short subsurface cracks under conditions of slip and stick caused by a moving compressive load. J Appl Mech, 1985, 52: 811–81710.1115/1.3169151 ↗
20. Liu J T, Du P A, Zhang Z Y. A general model of fatigue crack growth under variable amplitude loading. Sci China Tech Sci, 2012, 55(3): 673–68310.1007/s11431-011-4656-x ↗
21. Ringsberg J W, Bergkvist A. On Propagation of short rolling contact fatigue cracks. Fatigue Fract Engng Mater Struct, 2003, 26(10): 969–98310.1046/j.1460-2695.2003.00657.x ↗
22. Kong X A, Jiang X Y. Solid Contact Mechanics (in Chinese). Beijing: China Railway Press, 1999. 28–29
23. Shang D G, Yao W X, Wang D J. A new approach to the determination of fatigue crack initiation size. Int J Fatigue, 1998, 20(9): 683–68710.1016/S0142-1123(98)00035-8 ↗
24. Miller K J. The short crack problem. Fatigue Fract Engng Mater Struct, 1982, 5(3): 223–23210.1111/j.1460-2695.1982.tb01250.x ↗
25. Parker A P. Stress intensity factors, crack profiles, and fatigue crack growth rates in residual stress fields. In: Throop J F, Reemsnyder H S, eds. Residual Stress Effects in Fatigue. ASTM, STP, Phoenix, Ariz., 1982. 13–3110.1520/STP30095S ↗