journal article·2020-10-01

A novel OFDR-based distributed optical fiber sensing tape: design, optimization, calibration and application

Runzhou You, Liang Ren, Gangbing Song

Smart Materials and Structures· Volume 29· Issue 10
Publisher page

Abstract

Abstract The significance of implementing structural health monitoring (SHM) system for civil engineering, especially infrastructure engineering, has been recognized. Distributed optical fiber sensor (DOFS) based on optical frequency domain reflectometer (OFDR) offers an attractive technique for in situ strain measurement due to its high resolution and high precision. However, a main challenge that naturally arises is how to guarantee sensors survival in harsh construction and service environments. In this paper, a new, but simple, packaging technique is proposed to solve this issue. The novel sensing tape is fabricated by embedding DOFS into two fiberglass tapes and its strain transfer mechanism is analyzed in detail to provide scientific criteria for the choice of the material parameters. Then, a calibration test is carried out to evaluate the performance of the sensing tape in distributed strain measurement. Finally, the tape sensor is applied to the surface strain monitoring of the reinforced concrete (RC) beam tested in three-point bending. Experimental results verify that the sensing tape works well on concrete materials and the strain measured has the capability to reveal and localize cracks. Both analytical and experimental results demonstrate that the proposed packaging technique is feasible and effective.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Advanced Fiber Optic Sensors · Structural Health Monitoring Techniques · Analytical Chemistry and Sensors

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (56)

Show source-provided references
1. Karapetrou · 2017 · 46110.1016/j.proenv.2017.03.137 ↗
2. Comparative assessment of mechanical properties of HPS between electrochemical corrosion and spray corrosion10.1016/j.conbuildmat.2019.117735 ↗
3. Feasibility study of steel bar corrosion monitoring using a piezoceramic transducer enabled time reversal method10.3390/app8112304 ↗
4. Influence of cracks on chloride diffusivity in concrete: a five-phase mesoscale model approach10.1016/j.conbuildmat.2018.11.208 ↗
5. Vibration control of vortex-induced vibrations of a bridge deck by a single-side pounding tuned mass damper10.1016/j.engstruct.2018.06.099 ↗
6. Vibration suppression of wind/traffic/bridge coupled system using multiple pounding tuned mass dampers (MPTMD)10.3390/s19051133 ↗
7. Estimation of impact location on concrete column10.1088/1361-665X/aa6768 ↗
8. Impact force localization for civil infrastructure using augmented Kalman Filter optimization10.1016/j.proenv.2017.03.137 ↗
9. Bond-slip monitoring of concrete structures using smart sensors: a review10.3390/s19051231 ↗
10. An inverse finite element method for beam shape sensing: theoretical framework and experimental validation10.1088/0964-1726/23/4/045027 ↗
11. Cyclic crack monitoring of a reinforced concrete column under simulated pseudo-dynamic loading using piezoceramic-based smart aggregates10.3390/app6110341 ↗
12. New entropy-based vibro-acoustic modulation method for metal fatigue crack detection: an exploratory study10.1016/j.measurement.2019.107075 ↗
13. Bolt early looseness monitoring using modified vibro-acoustic modulation by time-reversal10.1016/j.ymssp.2019.04.036 ↗
14. Modeling and analysis of an impact-acoustic method for bolt looseness identification10.1016/j.ymssp.2019.106249 ↗
15. Identification of the structural damage mechanism of BFRP bars reinforced concrete beams using smart transducers based on time reversal method10.1016/j.conbuildmat.2019.06.056 ↗
16. Monitor concrete moisture level using percussion and machine learning10.1016/j.conbuildmat.2019.117077 ↗
17. Papadimitriou · Proc. 35th IMAC · 2019 · 13310.1007/978-3-319-74793-4_17 ↗
18. Investigation of bonding behavior of FRP and steel bars in self-compacting concrete structures using acoustic emission method10.3390/s19010159 ↗
19. Design of a new vision-based method for the bolts looseness detection in flange connections10.1109/TIE.2019.2899555 ↗
20. Monitoring of early looseness of multi-bolt connection: a new entropy-based active sensing method without saturation10.1088/1361-665X/ab3a08 ↗
21. Debonding detection of reinforced concrete (RC) beam with near-surface mounted (NSM) pre-stressed carbon fiber reinforced polymer (CFRP) plates using embedded piezoceramic smart aggregates (SAs)10.3390/app10010050 ↗
22. A low-cost IoT-based wireless sensor system for bridge displacement monitoring10.1088/1361-665X/ab2a31 ↗
23. Development of elasto-magnetic (EM) sensor for monitoring cable tension using an innovative ratio measurement method10.1088/1361-665X/aae0b0 ↗
24. An innovative structural health monitoring system for large transmission towers based on GPS10.1142/S0219455419710020 ↗
25. A load measuring anchor plate for rock bolt using fiber optic sensor10.1088/1361-665X/aa6ae8 ↗
26. A fiber bragg grating (FBG)-enabled smart washer for bolt pre-load measurement: design, analysis, calibration, and experimental validation10.3390/s18082586 ↗
27. Experimental and finite element analyses on the corrosion of underground pipelines10.1007/s11431-015-5824-1 ↗
28. Strain-based structural condition assessment of an instrumented arch bridge using FBG monitoring data10.12989/sss.2017.20.2.139 ↗
29. Urban bridges temperature measurement system based on fiber bragg grating sensing technology10.4028/www.scientific.net/AMM.361-363.1206 ↗
30. Slope stability analysis based on real-time displacement measurements10.1016/j.measurement.2018.09.019 ↗
31. Corrosion detection of steel reinforced concrete using combined carbon fiber and fiber Bragg grating active thermal probe10.1088/0964-1726/25/4/045017 ↗
32. Location identification of line supports using experimental modal analysis10.1016/j.measurement.2019.106996 ↗
33. A smart ‘shear sensing’ bolt based on FBG sensors10.1016/j.measurement.2018.03.026 ↗
34. Raman DTS based on OTDR improved by using gain-controlled EDFA and pre-shaped simplex code10.1109/JSEN.2017.2694343 ↗
35. A review of distributed optical fiber sensors for civil engineering applications10.3390/s16050748 ↗
36. Surface-enhanced Raman scattering biomedical applications of plasmonic colloidal particles10.1098/rsif.2010.0125.focus ↗
37. Monitoring and analysis of cast-in-place concrete bored piles adjacent to deep excavation by using BOTDA sensing technology10.1080/09500340.2018.1559948 ↗
38. Dynamic monitoring the deformation and failure of extra-thick coal seam floor in deep mining10.1016/j.jappgeo.2019.02.007 ↗
39. Recent progress of using Brillouin distributed fiber optic sensors for geotechnical health monitoring10.1016/j.sna.2017.03.017 ↗
40. Review on fiber-optic sensing in health monitoring of power grids10.1117/1.OE.58.7.072007 ↗
41. Distributed optical fiber sensors based on optical frequency domain reflectometry: a review10.3390/s18041072 ↗
42. Measuring the two-dimensional temperature profile of carbon fiber reinforced polymers during drilling using distributed fiber sensing10.1109/JLT.2019.2916914 ↗
43. Distributed fiber-optic pressure sensor based on Bourdon tubes metered by optical frequency-domain reflectometry10.1117/1.OE.58.7.072010 ↗
44. Embedded distributed optical fiber sensors in reinforced concrete structures-a case study10.3390/s18040980 ↗
45. Distributed fiber optics sensing and coda wave interferometry techniques for damage monitoring in concrete structures10.3390/s19020356 ↗
46. Bassil · 201910.12783/shm2019/32133 ↗
47. Pipeline corrosion and leakage monitoring based on the distributed optical fiber sensing technology10.1016/j.measurement.2018.03.018 ↗
48. Integration of long-gage fiber-optic sensor into a fiber-reinforced composite sensing tape10.1117/12.484262 ↗
49. Integration of distributed strain and temperature sensors in composite coiled tubing10.1117/12.661086 ↗
50. Distributed fiber optic strain and temperature sensing for structural health monitoring10.1201/b18175-412 ↗
51. A research on low modulus distributed fiber optical sensor for pavement material strain monitoring10.3390/s17102386 ↗
52. A novel method of embedding distributed optical fiber sensors for structural health monitoring10.1088/0964-1726/20/12/125018 ↗
53. Performance investigation of OFDR sensing system with a wide strain measurement range10.1109/JLT.2019.2918379 ↗
54. Mechanics of bond and interface shear transfer in optical fiber sensors10.1061/(ASCE)0733-9399(1998)124:4(385) ↗
55. Strain transferring analysis of fiber Bragg grating sensors10.1117/1.2173659 ↗
56. Strain transfer in distributed fiber optic sensor with optical frequency domain reflectometry technology10.1117/1.OE.58.2.027109 ↗